Table of Contents
Advertisement
One-Touch Editing from a VHS-C,
S-VHS-C or Digital Movie Camera
or VCR
This editing function makes it very easy to perform repeated
assemble editing, insert editing or audio dubbing as the
connected source unit can also be controlled with this VCR's
Shuttle Ring and Jog Dial.
Recording unit (this VCR)
Front
Edit cable
(supplied)
Video movie
camera
Preparations
≥ First confirm that both recording and source units are
connected to a AC mains socket.
≥ Press the MENU button
(3421)
to select "Functions" followed by "Edit", and
then set it to "ON". (See page 56.)
If the source unit also has an "Edit" setting (either a switch
or a menu setting), be sure to set it to "OFF" on the source
unit.
≥ Connect the EDIT socket
camera or a VCR using the Edit cable (VW-K5E), as shown
in the illustration.
≥ Display the VCR picture on the TV.
≥ Insert the cassette onto which you want to perform One-
Touch editing and make sure that its erasure prevention tab
is intact.
As soon as the cassette is inserted, the Cassette Number
Check starts. Wait a few moments until this check is
completed. (See page 16.)
≥ Insert the cassette, from which you want to perform editing,
into the source unit.
≥ Set the VCR/TV switch
≥ Press the INPUT SELECT button
(external input) "A1", "A2" or "A3" according to the socket(s)
to which you have connected the source unit.
A1: When connected to the AV1 21-pin Scart socket
[AV1 (TV)]
A2: When connected to the AV2 21-pin Scart socket
[AV2 (DECODER/EXT)]
≥ Make sure that "AV2" is set to "EXT".
(See page 55.)
A3: When connected to the Video Input socket
[VIDEO IN (AV3)]/the S-Video Input socket
[S-VIDEO IN (AV3)] and Audio Input sockets
[AUDIO IN (AV3)] on the front panel of this VCR
≥ When connecting a mono type movie camera or
VCR to this VCR's front AV sockets, connect to the L
(white) audio socket.
≥ Press the 3D DNR button
that 3D DNR lamp is not lit, to ensure editing with optimal
picture quality.
40
Other VCR
and then use the Cursor buttons
on this VCR to a video movie
to "VCR".
to select the AV input
to turn 3D DNR function off so
Operations
1
Press the Pause/Still button
use the Shuttle Ring
tape position from which you want to start recording.
2
Press the REC/OTR button
recording pause mode.
≥ This automatically puts the source unit in the still
playback mode.
≥ Instead of the REC/OTR button
button
to perform insert editing, or the A.DUB
Rear
button
for audio dubbing, or the INSERT
A.DUB buttons
3
Use the Shuttle Ring
search for point in the picture from the source unit from
which you want to start recording.
4
Press the Pause/Still button
editing.
≥ Playback on the source unit starts automatically at the
same time.
5
When you reach the point in the picture from the source
unit where you want to finish recording, press the Pause/
Still button
≥ This VCR is now in the recording pause mode and the
source unit in the still playback mode.
≥ To edit another scene, repeat operation steps 3 to 5.
6
Press the Stop button
≥ After you have finished editing, disconnect the Edit
cable.
Hints:
≥ If you want to change the audio recording level, adjust it.
(See page 22.)
≥ If you connect the optional Editing Controller
(VW-EC500E/EC310E/EC300E) to the EDIT socket
such editing functions as assemble editing, insert editing
and audio dubbing can be performed more quickly and
efficiently between this VCR and another VCR or a movie
camera.
on this VCR and then
or Jog Dial
to search for the
on this VCR to put it in the
, press the INSERT
simultaneously for AV insert editing.
or Jog Dial
on this VCR to
on this VCR to start
on this VCR again.
on this VCR to finish editing.
and
,
Hide quick links:
Advertisement
Table of Contents
