How To Use Menu Functions; Displaying Pc Screen On Tv - Panasonic Viera TH-37PV60EY Operating Instructions Manual

How to Use Menu Functions

■
Menu list
Item
Menu
Selects which AV terminal is to be used for data communication between this TV and a
Q-Link
compatible recording equipment (AV2 / AV3) (p. 24)
Chooses the signal to be transmitted from the TV to Q-Link (TV / AV1 / AV2 / AV3 /
•
AV4 / Monitor)
AV2/AV3 out
• Monitor: Image displayed on screen
Component, PC and HDMI signals cannot be outputted
Control with HDMI Control with HDMI function (Off / On) (p. 26)
Teletext
Teletext display mode (FASTEXT / List) (p. 12)
Off timer
Sets the time the unit automatically turns Off. (Off / 15 / 30 / 45 / 60 / 75 / 90) (minutes)
Volume correction
Adjusts volume for AV, PC and HDMI mode
• Increases the brightness of the side panel (Off / Low / Mid / High)
Side panel
The recommended setting is "High" to prevent panel "after-image"
Power save
Reduces brightness of picture to economise on power consumption (Off / On)
Set to "TV" to view picture from TV tuner.
Set to "AV" to view input from an external equipment connected to a SCART terminal,
e.g. satellite receiver
Power on preference
•
(TV / AV)
The external equipment must be switched on and sending a control signal for
automatic switching at power on to occur
Programme edit
Edits channels (p. 21)
Auto setup Sets channels automatically (p. 21)
Manual tuning
Sets channels manually (p. 21)
Fine tuning
Fine tuning of channels (during rain, etc.)
Owner ID
Inputs the owner ID (p. 23)
Shipping condition Resets all settings, for example, when moving (p. 22)
•
• A different menu will be displayed while PC is used.
In AV mode, the Setup menu gives a reduced number of options.
18
Adjustments / Configurations (alternatives)
(p. 19)

Displaying PC Screen on TV

The screen of the PC connected to the unit can be displayed on the TV.
You can also listen to PC sound with the audio cable connected. To connect PC (p. 28)
1
Select the external input
TV/AV
2
Select "PC"
TV/AV
yellow
OK
(Press twice)
■
To return to TV
■
PC menu setting (changed as desired)
•
To make settings "How to Use Menu Functions"
Menu Item Adjustments / Configurations (options)
Viewing mode, Contrast, Brightness, Sharpness, Colour balance (p. 17)
W/B High R White balance of bright red area
REC
VCR DVD
W/B High B White balance of bright blue area
PROGRAMME
Advanced
W/B Low R White balance of dark red area
setting
W/B Low B White balance of dark blue area
TV Gamma (2.0 / 2.2 / 2.5 / S Curve)
• Switches to a wide view
Input VGA (640 x 480 dots), WVGA (852 x 480 dots),
resolution • XGA (1,024 x 768 dots), WXGA (1,366 x 768 dots)
Options change depending on signals
Clock Set to the minimum level if noise occurs
Adjusts horizontal position
H-pos
PC
Adjusts vertical position
setup
V-pos
Eliminates flicker and distortion •
Clock phase
Adjust after Clock adjustment
Chooses another synchronous signal if the image is distorted (H&V / On G) •
Sync H&V : by the horizontal and vertical signals from your PC
On G : by the green signal from your PC (if available)
Volume correction, Side panel, Power save (p. 18)
•
Sound menu (p. 17)
To
next
page
blue
HDMI1/2
•
Corresponding signals
(p. 31)
•
If "H-freq." or "V-freq."
is shown in red, the
signals may not be
supported.
Displays PC screen
TV/AV
to (p. 16)
and
repeatedly adjusted
OK
OK
•
Set to the minimum level if noise occurs
19