Panasonic PV-V4022 Operating Instructions page 4

Multi-Brand Control Feature Advanced Connections
Multi-Brand Control Setup Audio/Video connection
The Remote Control can be set to control some TV functions. If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR
to them to receive higher quality picture and sound.
1
Find your TV Brand Code Number from those shown below.
2
Setup for TV control,
VCR
➛ hold down TV button,
➛ enter code with NUMBER keys.
3
Confirm code entry,
➛ press POWER to turn your TV on or off.
• See table below for controllable functions in each mode.
Notes • Repeat setup after remote battery replacement.
• Remote will not control every TV made by the manufacturer listed. If you get no
response, your particular unit cannot be controlled. There are NO additional codes for
the products listed. If your product is not listed, then the remote is not compatible with
that product.
VCR
Using Multi-Brand Control
After remote is set up, you can select VCR or TV for the desired function.
Press VCR or TV on the remote.
(Table below shows available unit buttons for each mode.)
Unit
VCR TV
Mode
VCR All VOL UP/DOWN
1
VCR/TV, PLAY, STOP, EJECT, SAP/Hi-Fi (PV-V4522 POWER, INPUT, ENTER,
Connect the VCR's VIDEO OUT jack to the TV's VIDEO IN jack.
TV only), DISPLAY, FF, REW, PAUSE/SLOW, REC, NUMBER keys, CH UP/DOWN,
SPEED, CM/ZERO, RESET COUNTER, TAPE POSITION
VOL UP/DOWN
2 PV-V4522 : Connect VCR's L/R AUDIO OUT jacks to the TV's L/R
Notes
• Not all functions listed may be controllable.
PV-V4022 : Connect VCR's AUDIO OUT jack to the TV's AUDIO IN
• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys for channel
selection.
3
Set the VIDEO/TV selector of your TV (Monitor/Receiver) to "VIDEO."
TV Brand Code Numbers
Panasonic ....................... 01, 02 Sylvania ................................. 05 JVC ....................................... 11
Quasar ............................ 01, 02 Sharp ............................... 06, 07 Hitachi ................................... 12
I I I I I With a Cable Box (VCR
RCA ...................................... 03 Sony ...................................... 08 Mitsubishi ........................ 07, 13
GE ......................................... 03 Toshiba ................................. 09 Samsung ............................... 14
Zenith .................................... 04 Sanyo .................................... 10 Gold Star ................... 15, 16, 17
Magnavox .............................. 05 Fisher .................................... 10 ANT AUDIO
or
CATV
VIDEO
Important Notes
IN 1 OUT
• Due to changes in infra-red commands used by manufacturers, some brands have several codes.
If your unit does not respond to the first code, please try the next one.
• Some TV brands require you to turn on the power manually.
I I I I I Connect With Two Cable Boxes
CABLE BOX
IN OUT
ANT
or 2-Way Splitter
CATV
OUT 1
OUT 2
- 2 -
V4022-4522 Advanced-2 (02-5-9) 2nd.p65 3
LSQT0523B(Advanced Operations) - Back
MTS Broadcast
For Model PV-V4522 only
Connection
Make the Audio/Video Connection as shown on page 3.
• You can use a TV connected to Stereo amp and speakers instead of a Stereo TV.
IN FROM ANT.
TV
TV
AUDIO OUT
R R AUDIO IN
L
R
L VHF/UHF
OUT TO TV
R
VIDEO OUT L
For Model PV-V4522 only
VIDEO IN
VHF/UHF
IN FROM ANT.
TV
AUDIO OUT
R
AUDIO IN VHF/UHF
OUT TO TV
VIDEO OUT
For Model PV-V4022 only
Receivable Broadcast Types
VIDEO IN
The following are possible audio broadcast types and on-screen displays.
The signal being received is indicated with an " " mark while the selected audio mode is
indicated with an arrow.
To display the broadcast signal being received,
➛ ➛ ➛ ➛ ➛ press DISPLAY*.
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main language)
AUDIO IN jacks.
and Secondary Audio Program (sub language)
broadcasts are being received simultaneously.
jack. Select STEREO or SAP audio mode.
MTS Stereo broadcast
Multi-channel Television Sound Stereo broadcast.
Select STEREO audio mode.
Cable Box)
• If stereo broadcast is weak and display flickers, select
You Can You Cannot
MONO audio mode for possibly better results.
TV • record
• view any
(including scrambled
IN FROM ANT.
IN OUT channels.
R scrambled)
R
CABLE BOX channel.
AUDIO
L L
VHF/UHF
SAP broadcast
IN OUT
OUT TO TV VIDEO
• use VCR
Secondary Audio Program (sub language) broadcast.
VHF/UHF Remote
Select SAP audio mode for the sub language.
Control to
VCR
select
channels
without using
Multi-brand
control feature.
MONO broadcast
You Can You Cannot
Normal monaural sound broadcast.
VCR
• view channel
• record and
view both other than
AUDIO IN FROM ANT.
the one
R scrambled and
selected for
unscrambled
L
VHF/UHF channels if any type of
VIDEO
OUT TO TV recording.
additional
TV equipment is
IN 1 OUT
added. This • do a Timer
A/B Switch IN OUT recording of
connection
Equipped with ® -TV Noise Reduction for true
R a channel
CABLE BOX AUDIO requires: two
MTS reproduction. ® -TV Noise Reduction is
L converter unless you
IN OUT IN 1 IN 2
VIDEO select it at required for good stereo separation and audio
boxes, an A/B
VHF/UHF switch, and a the cable fidelity. ® is a registered trademark, and is
2-way splitter. box.
licensed by ® Technology Licensing.
- 3 -
VHS Hi-Fi Stereo System
For Model PV-V4522 only
Audio Mode for Recording
1
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
2 Press SAP/ Hi-Fi repeatedly
to select desired mode.
STEREO
VCR
SAP
• Refer to "Receivable
MONO
Broadcast Types" on page 4.
Stereo Amplifier
AUDIO OUT
R R
L
• Arrow indicates selection.
AUDIO IN
R
3
Do a recording.
L
OUT TO TV See p. 5 of "Basic Operations" Instruction book.
Audio Mode for Playback
1
Start playback.
See p. 5 of "Basic Operations" Instruction book.
2
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
3 Press SAP/ Hi-Fi repeatedly
STOP 1 2 : 0 0AM CH 02
0 : 0 0 : 0 0 to select desired mode.
STEREO SP H I F I : L / R
SAP H I F I : L
H I F I : R • Select "HIFI(L/R)" or
MONO
NORMAL
"HIFI(L)" or "HIFI(R)" to
listen to stereo recordings in
stereo sound.
Select "NORMAL" for
• Arrow indicates
selection. monaural sound.
STOP 1 2 : 0 0AM CH 02
0 : 0 0 : 0 0
STEREO SP
SAP
MONO
Notes
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound.
STOP 1 2 : 0 0AM CH 02 Standard stereo tapes will playback in monaural sound.
0 : 0 0 : 0 0
STEREO SP • To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to
SAP
a stereo TV or an external stereo amp and speakers. (See page 4.)
MONO
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
• Hi-Fi and normal audio playback volume level may differ.
STOP 1 2 : 0 0AM CH 02
0 : 0 0 : 0 0
STEREO SP
SAP
MONO
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 4 - - 5 -
2002/05/09, 16:29
Tape Operation Tape Operation
Search System
Repeat Play
For each recording, an invisible index mark is placed on the tape. A program index and
Set to playback a recording over and over.
information are also included for timer recordings. These marks are used to access or
scan recordings. 1
Press ACTION to display menu.
Index Search Program End Search
2
VCR CLOCK CHANNEL
REPEAT PLAY :OFF
REMOTE WARNING :ON
Locates end point of recording for continuity. AUTO SHUT- OFF :OFF
1 SEARCH Press SEARCH* to
IDIOMA/LANGUE : ENGLISH
INDEX PROGRAM END VCR' S OUTPUT CH :3
display SEARCH in Stop
1
ENTER INDEX NUMBER :1
USING 1- 9 KEYS or Play mode, and then Press SEARCH twice to display SEARCH
SELECT : SET :
EXIT : ACT I ON
press NUMBER keys to
FORWARD SEARCH :FF in Stop or Play mode.
REVERSE SEARCH :REW
NEXT :SEARCH select recording
EXIT :STOP
number. 2 Press FF on the remote
SEARCH
INDEX PROGRAM END
to start PROGRAM
• To calculate number,
END SEARCH.
see below.
SEARCH START :FF 3
• To cancel, press
Press FF or REW on Press ACTION to return to normal screen.
PLAY or STOP.
the remote to start EXIT :SEARCH
search.
2 Play begins at search
INDEX SEARCH Examples of Program End Search.
end. To search forward Zero Search
or back 1 index, press
Fig. 1
FF or REW on the To quickly return to a specified tape location.
remote or VCR while Program 1 Program 2 or BLANK
FORWARD SEARCH :FF
REVERSE SEARCH :REW
screen left is displayed the current tape position
1
Press SEARCH button
(10 sec.). Press DISPLAY during play
End Point
FF
to display Counter.
• To cancel, press
PLAY or STOP.
Fig. 2
2
PLAY 1 2 : 0 0AM
0 : 0 0 : 0 0
SP
Program 1 BLANK Program 2 BLANK
the current tape position
Press SEARCH button
End Point
FF
To Calculate Index Number
Fig. 3
3
the current tape position
Example 1: Press SEARCH button Continue to record, playback, etc.
To go to rec. 2 from rec. 4, enter 3 and press
Program 1 BLANK Program 2
4
REW.
If search Press STOP.
FF
exceeds a few
End Point
seconds in
5
REW 1 2 : 3 0AM CH 02
BLANK area. 0 : 30 : 30
SP
1 2 3 4 5 6 7
Upon locating end point,
➛ search continues 7 sec. past end point,
Example 2:
➛ tape rewinds to 10 sec. before end point,
To go to rec. 6 from rec. 2, enter 4 and press
➛ tape plays to end point and stops.
FF.
STOP 1 2 : 3 1AM CH 02
0 : 0 0 : 0 0
Notes SP
1 2 3 4 5 6 7 • If Program End Search is started very
close to an index mark, that mark may be
skipped over.
NOTE: indicates start points of each recording.
• To cancel, press PLAY or STOP.
Note
• If Index Search is started very close to an
index mark, that index mark may not be
counted in the search.
*Important: If a remote control button does not work when pressed,
- 6 -
Commercial Skip
VCR fast forwards (skips) over 1~3 minutes
of recorded tape.
1
Press CM/ZERO in Play mode.
Press
• Press CM/ZERO repeatedly to change
to select REPEAT PLAY
skip time as shown below.
and press to set ON
or OFF.
ON : Play repeats at
tape end or if
PLAY
unrecorded portion
over 30 sec. is
detected.
1st Press 1 min Skip
2nd Press 2 min Skip
3rd Press 3 min Skip
• No indication appears.
Press RESET
COUNTER at desired
position to reset to
"0:00:00".
Press CM/ZERO in Stop
mode to start ZERO
SEARCH.
• Unit will go into FF or
REW mode and stop at
the last point the
Counter was set to
0:00:00.
press the VCR button on the remote and try the button again.
- 7 -