Camera Setup Menu; Setup Operation - Panasonic WV-CP160E Operating Instructions Manual

SETUP

1. CAMERA SETUP MENU

This camera utilizes a user setup menu that is displayed on-screen.
• Opening the Setup Menu
Press and hold down
more.
The CAM SET UP menu appears on the
monitor as shown at right.
Check the current settings on the menu.
Refer to the sections below for a detailed description of menu items. If you decide not to
make any changes after checking the current settings, move the cursor to END at the start
of the bottom line, and press
era picture mode.
Note: If no button is pressed for 6 minutes while the CAM SET UP menu or any other menu
is opened, the menu is automatically closed and the mode returns to the normal cam-
era picture.

2. SETUP OPERATION

This camera utilizes a user setup menu
(CAM SET UP) that is displayed on the
monitor.
To set items on the CAM SET UP menu, use
the following buttons on the side panel.
Up Button ( ):
Down Button ( ): Moves the cursor downwards. Use this button to select an item or
Right Button ( ): Moves the cursor to the right. Use this button to select or adjust the
Left Button ( ):
Set Button ( ):
To return to the CAM SET UP menu
Move the cursor to RET and press
• All Reset Operation
All Reset allows you to reset all setup menu items to the factory default settings if you are
unsure about the correct settings. Proceed as follows:
(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
(2) While pressing both
RESET momentarily appears on the monitor.
This resets all adjustments and parameters to the factory default settings.
• Editing the CAM SET UP Menu
Important Notice:
When the SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you
cannot change the currently active settings. This is to prevent accidental changing of
the settings.
To edit the CAM SET UP menu (change
settings), press
to move the cursor to SET UP DIS-
ABLE in the bottom line.
Press . SET UP DISABLE changes
to SET UP ENABLE. Move the cursor to
END, then to the item(s) you want to
change.
• Editing the SPECIAL Menu
To edit the SPECIAL menu (change set-
tings), proceed as for editing the CAM SET
UP menu above. Move the cursor to END
after the SET UP ENABLE appears. Then
press and
down and press
more.
The SPECIAL menu appears on the moni-
tor. Select the item to be changed and
change the setting as described for the
CAM SET UP menu.
Important Notice:
When the cursor is moved to END and the CAM SET UP menu closed after changing
the parameters, the new values are saved in the EEPROM (Electric Erasable and
Programmable Read Only Memory). These values remain valid until new values are
saved, even if the power of the camera is off.
for 2 seconds or
to close the CAM SET UP menu and return to normal cam-
Moves the cursor
upwards. Use this button to select an item or adjust the parameters.
adjust the parameters.
parameters of the selected item. The parameter changes each time
this button is pressed.
Moves the cursor to the left. Use this button to select or adjust the
parameters of the selected item. The parameter changes each time
this button is pressed.
Executes selections and displays a submenu for an item with
END: Close Setup menu.
RET: Return to the previous menu.
. The CAM SET UP menu appears.
and
and or and
simultaneously (holding
) for 2 seconds or
CAMERA ID
ALC/ELC
SHUTTER
AGC
SENS UP
WHITE BAL
AUDIO LEVEL
END
Left Button
Set Button
, press for a few seconds. The message ALL
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
-
END SET UP DISABLE
UP SIDE DOWN OFF
CHROMA GAIN
AP SHARP
PEDESTAL
CAMERA RESET
** CAM SET UP **
OFF
ALC
OFF
ON
OFF
ATW
....I....
-
SET UP DISABLE
** CAM SET UP **
CAMERA ID
ALC/ELC
SHUTTER
AGC
SENS UP
WHITE BAL
AUDIO LEVEL
+
END
** SPECIAL **
....I....
....I....
.I.......
-
PUSH SW
RET END
(To be continued reverse page)
Highlighted
+
Up
Button
Right
Button
Down
Button
mark.
OFF
ALC
OFF
ON
OFF
ATW
....I....
- +
SET UP ENABLE
+