Heli-Max TX610 User Manual
  1. Manuals
  2. Brands
  3. Heli-Max Manuals
  4. Transmitter
  5. TX610
  6. User manual

Heli-Max TX610 User Manual

2.4ghz helicopter radio system
Hide thumbs
Table of Contents

Advertisement

Quick Links

USER MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TX610 and is the answer not in the manual?

Questions and answers

Marcos
May 22, 2025

Can this be used on anything other than rc planes and helicopters

User image 682ec33c5f0d9
0
1 comments:
Mr. Anderson
May 25, 2025

No. The Heli-Max TX610 is designed specifically for RC planes and helicopters.

This answer is automatically generated

0

Summary of Contents for Heli-Max TX610

  • Page 1 USER MANUAL...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION ........3 WARRANTY SERVICE .

  • Page 3: Introduction

    The TX610 computer transmitter can be used to control model airplanes as well as model helicopters. It employs advanced 2.4GHz communication technology. In order to make the best use of your TX610 and to operate it safely, please read all of the instructions.

  • Page 4: Specifications

    Up-1/Gear Trainer Hold/Flap ATV (D/R) Hov.T/Flap.T Gyro/Gear Mode Enter (Push) Back Adjust (Turn) SPECIFICATIONS Battery Requirements: 8AA dry cell (sold separately) Operating current: 100 to 150mH Operating voltage: Range of 8.5V to 13V Transmitting Power: 2+dBm FEATURES • SLT (Secure Link Technology) •...

  • Page 5: Turning The Transmitter On

    5. Turn the HOLD switch off to begin operation. TURNING THE TRANSMITTER ON When turning your TX610 on, make sure the switches located near and at the top of the transmitter are switched into the “back” position. Also make sure the transmitters throttle stick is in the low position or a safety warning alarm will sound and a T-H will appear on the LCD screen.

  • Page 6: Model Type

    6. Press BACK to escape and save the setting. MODEL TYPE (SWITCHING BETWEEN PLANE & HELI MODE) The TX610 allows you to have both airplane and helicopter model types setup into your transmitter. Models 0 thought 9 could be either airplane or helicopter or a mix of both.

  • Page 7: Range Check

    5. Rotate ADJUST to scroll between the two options. 6. Push ENTER to accept. 7. Press BACK to exit and save the setting. RANGE CHECK MODE (P-H) This allows the user to ground test the range of the radio system. (NOTE: Do not fl y the model with the transmitter in Range Check Mode) 1.

  • Page 8: Atv

    6. When done use the BACK button to exit and save the settings. CURVE/S EXPO Channels 1, 2, and 4. - 5 point throttle curve on Channel 3. NOTE: The TX610 also has a 5 point pitch curve on Channel 6 (HELI ONLY). We will cover this in the Helicopter Section of the manual.

  • Page 9: Sub Trim

    ON/DOWN, the user dials in the amount of fl ap defl ection desired using the HOV.T/FLAP.T dial. GEAR SPEED: (SLOWING DOWN A RETRACT SERVO) The TX610 allows you to adjust the transit speed to channel 5 servo (landing gear). You may adjust different speeds for both up and down. 1. Turn on your transmitter.

  • Page 10: Mixing

    ADJUSTMENTS (HELICOPTER MODE) CCPM MIXING: (120° SWASHPLATE ARRANGEMENT ONLY) The Heli-Max 610 allows you to mix the swashplate to compensate for either up- down, left-right, or forward-back cyclic commands. Channel 1 represents side to side (aileron), Channel 2 represents forward and back (elevator) and Channel 3 up and down (Pitch).

  • Page 11: Gyro Gain

    6. Press either the MODE or ENTER button. The channel mixing selection, 1, 2 or 3 (see selection information above), as well as the swashplate icon will fl ash. 7. Turn the ADJUST dial to adjust the value, note either a + or – value and the relationship they have on direction.

  • Page 12: Pitch Curve

    5. Rotate the ADJUST DIAL to turn the MIX feature ON (Channel 1 fl ashing) or OFF (Channel 1 hidden). 6. Press ENTER again to enter the channel MIX menu. You will see the Channels 3 and 4 fl ashing. 7.

  • Page 13: Adjusting The Throttle Curve In Normal

    ADJUSTING THE THROTTLE CURVE IN NORMAL The throttle curve can be adjusted to optimize the power to the motor depending on stick position and blade load. 1. Turn on your transmitter. 2. Press the MODE button for one second. You have entered model setup. 3.

  • Page 14: Trainer System

    TRAINER SYSTEM Make sure the instructor’s transmitter is properly bound to the model, and the instructor’s transmitter, student’s transmitter and helicopter are not powered on. 1. Connect the trainer cord to the instructor and student’s transmitter via the plug in sockets located on the back of the transmitters.

  • Page 15: Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

     M ode 2 has the Aileron and Elevator, the two main controls, on the right stick. The Throttle and Rudder are on the left stick. This is how your TX610 comes delivered from the factory.
  • Page 16 Product: Heli-Max TX610 2.4GHz 6-Channel Tx Rx Item number: HMXJ2025 TX610, Equipment class: 1 TX610 transmitter: The objects of the declaration described here are in conformity with the requirements of the specifications listed below, following the provisions of the European 2006/95/EC Low...

Table of Contents