Saferhome HB-G100 Series User Manual

Intelligent burglar alarm host

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

HB-G100

HB-G100 Series

User

Manual

User

User Manual

Manual for

Burglar

Burglar Alarm

Ningbo

Ningbo Saferhome

We are

are

are honoured

honoured

honoured that

Thanks

Thanks for

for

for your

for

your

your wise

your

and

and ensure

ensure

ensure stable

ensure

stable

stable operation

User

User Manual

Manual

Manual before

before

before operating

before

don

don' ' ' ' t t t t hesitate

hesitate

hesitate to to to to consult

agents.

Series

Saferhome

Saferhome Electronics

that

that you

that

you

you have

wise

wise selection.

selection.

selection. To To To To make

selection.

operation of of of of the

operation

operating the

operating

consult

consult our

our

our Customer

our

Customer Service

Customer

for

Intelligent

for Intelligent

Intelligent

Alarm

Alarm Host

Electronics

Electronics Co.,

have

have chosen

chosen

chosen our

our

our security

our

make

make full

full

full use

full

the

the host,

host,

host, please

please

please carefully

the

the host.

the

host.

host. For

For

For any

any

any questions,

any

Service

Service Department

Host

Co.,

Ltd.

Co., Ltd.

Ltd.

security

security products.

security

products.

use

use of of of of its its its its performance

performance

carefully

carefully read

read

read this

questions,

questions, please

questions,

please

Department or or or or

Department

this

Table of Contents

Summary of Contents for Saferhome HB-G100 Series

Page 1 HB-G100 HB-G100 Series Series HB-G100 HB-G100 Series Series User User Manual Manual Intelligent Intelligent User User Manual Manual for for Intelligent Intelligent Burglar Alarm Host Burglar Alarm Host Burglar Burglar Alarm Alarm Host Host Ningbo Ningbo Saferhome Saferhome Electronics Electronics Co.,...
Page 2: Table Of Contents
Table Table Table of of of of Contents Contents Contents Table Contents Definition................2 II. Operating Precautions............4 III. Main Characteristics and Functions........4 IV. Name and Usage of Main Components......6 V. System Installation.............11 VI. Operating Instructions............12 VII. How to Program Alarm Host..........18 VIII.
Page 3: Definition
Introduction Introduction Introduction HB-G100 Series Intelligent Burglar Alarm Host is an intelligent long-range wireless transmission alarm system. This system adopts advanced microprocessor as control core and has voice prompts, easy to install and operate. It can learn codes of 5 remote controllers and 120 HB-T001 Series solar-powered wireless active infrared detectors, all of which constitute a complete long-range wireless alarm service system.
Page 4 zone) in which the host can receive shielded signals, and can not receive any alarm signal temporarily. Full Full It refers to the state in which all alarm detectors in full arming zone or Full Full Arm part arming zone enter into alert state. Partial Partial Partial...
Page 5: Operating Precautions
II. II. II. II. Operating Operating Precautions Operating Operating Precautions Precautions Precautions � Please carefully read this User Manual and pay more attention to labels and directions on the alarm host before operation. Check whether all wire connections are correct and then turn the host on so as to avoid any damage to the host.
Page 6 security threats and 2 groups of telephone numbers of the alarm receiving centre. The telephone numbers of the alarm receiving centre must be fixed telephone numbers, which can be dialled preferably when an alarm is triggered under telephone alarm mode. �...
Page 7: Name And Usage Of Main Components
Name Usage Usage of of of of Main Main Components IV. Name Name Name and and Usage Usage Main Main Components Components Components Keyboard Panel Keyboard Keyboard Keyboard Panel Panel Panel 1 1 1 1 、、、、 Keyboard Keyboard Keyboard Keyboard...
Page 8 host gets ready for receiving alarm signals from partially armed zones within the system and giving out alarm. 6) “RECORD” Indicator: In set-up mode, users can prerecord a voice message to play back at the time when a call is answered to respond to an alarm. When a voice message is recorded, “RECORD”...
Page 9 minute. 15) “Emergency Zone” Indicator: “Emergency Zone” Indicator will light up only when set-up is performed for an emergency zone. Once emergency zone set-up is completed, the indicator is not turned on even when an alarm occurs. 16) “Doorbell Zone” Indicator: “Doorbell Zone” Indicator will light up when set-up is performed for a doorbell zone.
Page 10 Installation Installation & & & & Wiring Wiring Diagram Diagram of of of of Engineering Engineering Host Installation Installation Wiring Wiring Diagram Diagram Engineering Engineering Host Host Host...
Page 11 ① Mains Supply Input: The alarm host adopts AC 220V±10% 50Hz input, and the input terminal is connected in series with a 0.5A fusion tube. ② External Backup Battery Input: The host adopts DC12V7Ah external backup battery input. ③ External Siren Output: A DC 12V siren (current: <0.6A) can be connected to the alarm host.
Page 12: System Installation
Connection Principle: The normally open detector shall be connected in parallel with a 2.7KΩ resistor, while the normally closed detector shall be connected in series with a 2.7KΩ resistor. Detector1 Detector2 Detector 3 Detector1 Detector2 Detector 3 2.7k 2.7k Connection of several normally open detectors Connection of several normally closed detectors Mixed connection of normally open detectors and normally closed detectors V.
Page 13: Operating Instructions
from damaged by mouse or other rodents. ④ The type and specification of detectors and cables in each defense zone should be labeled on construction drawings (The usage of each wire within a cable shall be marked). ⑤ All construction drawings should be archived for facilitating maintenance of the host system.
Page 14 intended for the host, and defense zones 000-007 are mixed wired/wireless defense zones in which it is not recommended to install wireless detectors. Add/Delete Add/Delete Remote Remote Controllers Controllers Add/Delete Add/Delete Remote Remote Controllers Controllers The host can learn codes with 5 remote controllers, which are numbered 10， 11，12，13，14 respectively.
Page 15 panel of the host. “Disarm” Key: Press “Disarm” key to disarm the host (except for shielded zone, doorbell zone and emergency zone). The function of “Disarm” key is the same as that of F3 shortcut key on the keyboard panel of the host. Emergency Key: Press Emergency Key to activate emergency alarm whether the host is in Arm mode or Disarm mode.
Page 16 The first four steps of deleting a remote controller are the same as those of adding a remote controller. Step 5: Enter 19 and # after 19, and then the host gives out a voice prompt “Delete all remote controllers”. Step 6: Press “#”...
Page 17 【Note】 a. Detectors (numbered 000-119) shall be added in accordance with the same procedure. b. To let the host learn codes of detectors continuously, enter 011 and # 11 after the host completes learning the first detector, and then activate the next detector to let the host learn the code of the next detector until the host completes learning codes of all detectors.
Page 18 those of adding a detector, so please refer to the first four steps of the procedure for adding a detector. Step 5: Enter “010” and “*”, and then the host will give out a voice prompt “Now, the host is serving a fully armed zone. Please enter the attribute of the defense zone”(The attribute of all defense zones is set to “...
Page 19: How To Program Alarm Host
Reasons Failing Failing to to to to Learn Learn Codes Reasons Reasons Reasons for for Failing Failing Learn Learn Codes Codes Codes Coding Redundancy: If the wireless code currently required to be learned by the alarm host has exited in the alarm host, that is, this code has been learned by the alarm host, it can not be learned again by the alarm host.
Page 20 Dialling Times: 5 Siren Duration: 30 minutes Leaving Time: 5 seconds Entry Time: 0 second 10) Ringing Times Set via Remote Control: 9 times 11) Defense Zone Attribute: Full Arm 3. Detailed Programming Operation of Alarm Host All programming operations below shall be performed in set-up mode. The Procedure for Entering into Set-up Mode: Step 1: Enter “# # #”...
Page 21 ② Command Function: On-site Alarm Mode Command Grammar: 3# Function Description: This command enables the host to work under on-site alarm mode in which the host can not dial any telephone and check outside line, as well as to cancel all alarm information. Operating Steps: “###”（Please enter the preset password）+ “112233#”（The host enters into adjusting mode ）...
Page 22 again）+“BBBBBB#”. If you have forgotten the preset password indiscreetly, you shall contact our customer service centre or your local distributor for help. 5) Command Function: Modify User Password Command Grammar: 9 # A A A A A A # B B B B B B # B B B B B B #. “A A A A A A”...
Page 23 Step 3: Enter “10” (10 represents informed phone number) and “#”, and then the host will give out a voice prompt “Please enter an informed phone number”. Step 4: Enter a preset phone number and “#” to finish the set-up. (If the input phone number is wrong, delete it and then enter a correct phone number.
Page 24 For the first two steps, please refer to the above mentioned procedure in SET mode. Step 3: Enter 19 and #, and then the host will warn users through voice message to delete all informed phone numbers”. Step 4: Press “#” key again, and then the host will indicate a remote controller has been successfully deleted.
Page 25 Press 2 5 # to select the medium on-site alarm volume; Press 2 6 # to select the large on-site alarm volume Press 2 7 # to select the maximum on-site alarm volume Operating Steps: “###” （ Please enter the preset password） +“112233#” （ The host enters into adjusting mode）...
Page 26 ② Command Command Command Function: Function: Audition Audition Record Record Command Function: Function: Audition Audition the the Record Record Command Grammar: 3 1 # Function Description: Press 3 1 #, and then 2-3 seconds of record will be played from the built-in speaker of the host. 7.
Page 27 ② Command Function: Set leaving time Command Grammar: 3 5 # D D # Function Description: “D D” refers to leaving time, also called delayed ARM time and must be a 2-digit number (00-99 minutes). Within the leaving period of time, the alarm host gives out a short “Beep”...
Page 28: Add/Delete Detectors And Remote Controllers
⑤ Command Function: Set dialling times Command Grammar: 3 8 # D D # Function Description: “D D” refers to dialing times (01-99), namely how many times the host dials phone numbers according to a list of preset phone numbers. Note: This set-up does not apply when the host dials phone numbers of the alarm receiving centre.
Page 29 2. Modify Alarm Mode and Arm/Disarm in SET Mode Enter # # # A A A A A A # to enter into set-up mode and modify alarm mode. ① Arm the host in phone alarm mode Enter 1 # to arm in phone alarm mode and exit set-up mode. ②...
Page 30 arm/disarm methods in "Arm/Disarm Operation" to arm the alarm host and to ensure the system is on alert. The alarm host will automatically alarm according to the pre-set alarm procedure as soon as someone breaks into a defense area. Emergency Alarm (or Help) If any emergency circumstance such as robbery occurs in your residence or workplace, the system will enter into alarm mode whether the alarm host is in arm mode or in disarm mode when pressing the “Emergency Button”...
Page 31: Main Technical Specifications
phone numbers. 4. 4. 4. 4. Remote Remote Remote Set-up Set-up Remote Set-up Set-up Call the phone numbers pre-set for the user alarm host through fixed phone or mobile phone in other areas, and then the user alarm host will automatically pick up the phone after receiving several rings (program default: 9 times ) and at the same time you can hear a voice prompt “Welcome to Use Hengbo Security Product”.
Page 32: Standard Configuration List
Operating Conditions: -10-55℃ Relative Humidity: 40-70% Dial Mode: Double Audio Frequency High Frequency Group Level: -7 ± 2dBm Low Frequency Group Level: -9±2dBm Pick-up Resistance: ≤300Ω External Backup Battery: DC12V7Ah Dimension: 265×260×80（mm） 2. 2. 2. 2. Wireless Wireless Wireless Wireless Remote Remote Remote Remote Controller...
Page 33: Failure Troubleshooting
XII. XII. Failure Failure Troubleshooting Troubleshooting XII. XII. Failure Failure Troubleshooting Troubleshooting Failure Symptom Reason Failure Recovery Method Power plug is not “RUN” Indicator does not properly connected, or Check power plug or socket light up when powered on socket has no power Enter correct user password or User password is wrong, The host fails to enter into...
Page 34: Programming Set-Up And Other Operating Commands
LED “Power Failure” The battery of the indicator lights up and detector for this defense Replace the battery displays defense zone zone is damaged. number. The remote distance of The voltage of the battery remote control becomes Replace the battery is low.
Page 35 1 1 # # Delete the second group of informed phone numbers 1 2 # # Delete the third group of informed phone numbers 1 3 # # Delete the fourth group of informed phone numbers 1 9 # # Delete all phone numbers 2 4 # Select small alarm volume...
Page 36 Warning: Warning: Limits Limits Limits of of of of This This This Security Security System System Warning: Warning: Limits This Security Security System System As an advanced hi-tech anti-theft system, although this product can reduce and prevent the occurrence of theft, robbery and fire and thus reduce loss, we can not guarantee no above-mentioned accidents happen or no personal casualty and property loss happens.
Page 37 the alarm center, or other lines are busy, so that alarm information can not be transmitted in time. The alarm system does not alarm when someone intrudes or there is an emergency alarm. The most common reason is that the alarm system does not get properly maintained.