Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Hughes & Kettner CONTOUR Series
- Page 1 Manual 1.0 ConTour Series™ English...
- Page 2 Important Advice on Safety! Important Safety Instructions Wichtige Sicherheitshinweise! Please read before use and keep for later use! Before connecting, read instructions Bitte vor Gebrauch lesen und für späteren Gebrauch aufbewahren! • Read all of these instructions! • The unit has been built by HK AUDIO ®...
- Page 3 Importanti avvertimenti di sicurezza! ¡Indicaciones de seguridad importantes! Conseils de Securite Importants! Leggere attentamente prima dell'uso e conservare per ¡Léanse antes de utilizar el aparato y guardense para Priere de lire avant l'emploi et a conserver pour uti- un utilizzo successivo: so uso posterior! lisation ulterieure! •...
-
Page 4: Table Of Contents
2.2 Maintenance, Inspection and Repair of ConTour Series™ Rigging Hardware ....... -
Page 5: A Notes On Rigging Safety
CT 115 1 Warranty and The ConTour Series™ Rigging System’s provisions 2.2 Maintenance, Inspection and Repair of Liability for use require that it be installed in accordance HK AUDIO ®... -
Page 6: Mounting
193 543 license! Arrest wire Additional securing cable for flown CT 112/ CT 115 2.6 Structural Modifications of ConTour Series™ speakers; 4 mm in diameter, 100 cm in length, Rigging Hardware including snap links No structural modifications may be made without the manufacturer’s consent. -
Page 7: B Contour Series™ Speakers
B ConTour Series™ Speakers top and bottom panels, as well as the right and 1.2 Adjusting Directivity 1 CT 108 left panels. A 360° mounting yoke and a 35-mm The HF horn’s mounting yoke is square, enabling pole mount adapter are optionally available. -
Page 8: Technical Data, Ct 108
ConTour Series 1.0 1.4 Technical Data, CT 108 Power-handling nominal/ program/ peak: ........200 W RMS / 400 W / 800 W Recommended amplifier power: . -
Page 9: Ct 112
34 cm deep, and weighs 25 kg. The surface is 2 CT 112 coated with black water-repellent acrylic lacquer. The front baffle is protected by a steel grille. The enclosure’s panels are equipped with a total of two Aeroquip rigging tracks and two threaded M10 bushings. -
Page 10: Technical Data, Ct 112
ConTour Series 1.0 with a 35-mm TripleTilt™ 3-way Pole Mount enclosure’s top and bottom panels. 10% THD under half-space conditions. Power Adapter offering +5°; -3° and –10° tilt angles, two An internal passive crossover splits the signal at handling is 400 watts RMS; nominal impedance Aeroquip rigging tracks, and two threaded M10 850 Hz (12 dB/octave);... -
Page 11: Ct 115
Enclosure design and mechanical appointments: 3 CT 115 The CT 115’s enclosure is constructed of 18-mm, 13-ply birch plywood. Shaped to serve dual functions, the housing is 45 cm wide, 69.5 cm high and 39 cm deep, and weighs 33 kg. The sur- face is coated with black water-repellent acrylic lacquer. -
Page 12: Technical Data, Ct 115
ConTour Series 1.0 pivoting 60° x 40° / 40° x 60° Constant Directivity protects the front baffle. Four recessed handles Power handling is 600 watts RMS; nominal horn. Made of 18-mm birch plywood coated with are located on the enclosure’s top, bottom and impedance is 8 ohms. -
Page 13: Ct 118 Sub
@1W/1m under half-space conditions, and 129 dB the ConTour Series™ cabinets CT 108, CT 112 and 4.1 Optional Passive Crossover for the CT 118 Sub maximum SPL at 10% THD under half-space CT 115. -
Page 14: Technical Data, Ct 118 Sub
ConTour Series 1.0 4.3 Technical Data, CT 118 Sub: Power-handling nominal/program/Peak: ........1000 W RMS / 2000 W / 4000 W Recommended amplifier power: . -
Page 15: C Rigging Contour Series™ Ct 108/ Ct 112/ Ct 115 Enclosures
C Rigging ConTour Series™ CT 108/ CT 112/ CT 115 Enclosures Please also read the Notes on Rigging Safety in Chapter A of this manual. ConTour Series™ Rigging Hardware for CT 112 and CT 115 enclosures enables the cabinets to be flown from a single pick-point. -
Page 16: Ms/1, Ms/2, Ms/3 Mounting Set For The Ct 108
ConTour Series 1.0 1.3 MS/1, MS/2, MS/3 Mounting Set for the CT 108 A three-piece mounting set is available for the CT 108, enabling the speaker to be placed on a pole or flown from a truss. MS/1: An L-shaped mounting bracket, the MS/1 can be attached either to the left or right side panel. -
Page 17: D Contour Series™ Controller Settings
40 kHz. It offers input shifting and group delay even at maximum slopes ConTour Series™ speakers for use in both FOH delays ranging up to 400 ms and output delays to preserve the signal’s natural sound. This and (bi-amped) monitor applications. -
Page 18: E Service
ConTour Series 1.0 E Service 2.2 The Drivers’ Voice Coils 1 ConTour Series™ Replacement Parts Proceed as follows to replace the drivers’ voice coils: Note: • Remove the front grille as described above. • If your equipment requires service, please turn •... - Page 19 ® ® HK AUDIO HK AUDIO ConTour Series™ CT 118 Sub ConTour Series™ CT 118 Sub wird hiermit bestätigt, dass sie den wesentlichen Schutzanforderungen complies with the provisions of the Directive of entsprechen, die in der Richtlinie des Rates zur Angleichung der Rechts- the Council of the European Communities on the approximation of the vorschriften der Mitgliedsstaaten über die elektromagnetische Verträg-...
- Page 20 ® Specifications subject to change without notice. HK Audio • Postfach 1509 • 66595 St. Wendel Copyright 2006 Music & Sales GmbH • 02/2006 Germany • info@hkaudio.com • www.hkaudio.com International Inquiries: fax +49-68 51-905 215 international@hkaudio.com...