Summary of Contents for TERABEAM AP-Ext-N
- Page 1 AP-Ext-N User Manual Contact Terabeam www.terabeam.com 8000 Lee Highway Falls Church, VA 22042 Office: 703-205-0600 Fax: 703-205-0610 Sales: 1-888-297-9090 MNL-500275-001 Version 1.0 Jun 2005...
- Page 2 Terabeam Wireless (Terabeam) warrants that your device is free of defects in material and workmanship for a period of one year after initial purchase. Terabeam will, in this period of time, repair or replace, any Terabeam product returned to the factory, freight prepaid.
-
Page 3: Table Of Contents
Power Supply ..........................6 Hardware Installation ........................6 © 2005 Terabeam Wireless. All Rights Reserved. No part or parts of this document may be reproduced, translated, stored in any electronic retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopied, recorded or otherwise, without the prior written permission of Terabeam Wireless. -
Page 4: Overview
Overview Description The AP-Ext-N is an 802.11b Access Point (AP) built into a flat panel enclosure. It is ideal for providing maximum coverage over a focused area, such as 802.11b Hot Spots, hotels, airports, office buildings, apartment complexes, etc. It is easy to install and features the functionality of the Terabeam AP-Plus Access Point, including 128-bit WEP (Wired Equivalent Privacy) and the new Agere WEP-Plus. -
Page 5: Ap-Ext-N Features
110/220 VAC to 48 VDC Power Supply • CD-ROM with Windows-based software and documentation A Terabeam outdoor Ethernet cable must be ordered separately. Available lengths are 50, 100, 200, or 300 feet (maximum length). The latest software and User’s Manuals can also be found at: http://www.terabeam.com/support/downloads.php, and... - Page 6 AP-Ext-N User Manual Figure 1.1a – AP-Ext-N, 110/220 VAC Power Supply, and DC Power Injector Figure 1.1b – Typical Application Omni Antenna AP-Ext-N Short Coax Cable Ver 1.0 Page 3 Jun 2005...
-
Page 7: Installation
CAUTION! Locating the AP-Ext-N The most important aspect of setting up the AP-Ext-N is the location and aiming of both the unit and its external antenna. For maximum range (up to several miles), the antenna must have clear, unobstructed line of site (LOS) and Fresnel Zone between it and the client stations’ antennas. The AP-Ext-N should be installed outdoors as close as possible to its antenna so that the coax cable between the antenna and the unit is kept as short as possible. - Page 8 Roun onnecto Short Coax Cable Ethernet Cable to DC Power Injector (maximum 300 feet) Table 2.1 – Recommended External Antennas for the AP-Ext-N and AP-LR-Ext-N Terabeam Model No. Description A2408 Omnidirectional, 16 in, 8 dBi gain, 2400 – 2500 MHz A2412-O Omnidirectional, 65 in, 12 dBi gain, 2400 –...
-
Page 9: Dc Power Injector
1. Use the brackets and screws to mount the flat panel enclosure to a pole with a maximum diameter of up to 1 3/4 inches, as close as possible to the antenna. 2. Connect the antenna to the N-type connector in the back of the AP-Ext-N using a short coax cable as shown in figure 2.1 3. - Page 10 (refer to Fig. 2.4). Also, a water-proof plug is located next to the LED label. You may remove this plug to gain access to a reset push button inside the AP-Ext-N for disaster recovery, or if so instructed by your Terabeam support representative during troubleshooting or technical assistance.
Need help?
Do you have a question about the AP-Ext-N and is the answer not in the manual?
Questions and answers