Do you have a question about the L224WS and is the answer not in the manual?
Questions and answers
Thaheer BS
March 1, 2025
how to contact the service provider to change the display of L224WS
1 comments:
Mr. Anderson
March 1, 2025
The manual advises checking the label attached to the product and providing the information to your dealer when requesting service. If the power cable is faulty, contact the manufacturer or the nearest authorized repair service provider for a replacement.
Page 1
User’s Guide L224WS ake sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. ee the label attached on the product and give the information to your dealer when you ask for service.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.
Page 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand Place the monitor with its front facing downward on a soft cloth. Check the direction of the Stand Body, and connect it into the Hinge Body as shown in the picture.
Connecting the Display Disassembling the stand Put a cushion or soft cloth on aflat Place the monitor face Down on surface. the cushion or soft cloth. Head Part Stand Base Part Hold the Head Part with one hand and Pushing Latch inside, Take the hold the Stand Base Part with the other stand base from stand body.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~20˚...
Connecting the Display Using the Computer Make sure to turn off the computer and product. Connect Signal cable and Power cord in order, then tighten the screw of the signal cable. Connect Dsub Cable (PC). Connect Dsub Cable (Mac) NOTE This is a simplified representation of the rear view.
Control Panel Functions Front Panel Controls 4 : 3 in Wide It allows you to adjust the size of screen you are watching now. Button • WIDE : The video source is displayed in full screen size. • 4 : 3 : Depending on the input video signal ratio, it is automatically changed to an optimized screen ratio.
Page 9
Control Panel Functions Use these buttons to select or adjust functions in the On Buttons Screen Display. LightView hot key This feature lets you easily select the best desired image condition optimized to the environment NIGHT (ambient illumination, image types etc). •...
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD.
Page 11
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub menu Reference To adjust the brightness, PICTURE BRIGHTNESS contrast and gamma of the CONTRAST screen GAMMA COLOR PRESET sRGB To customize the color of the screen...
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
Page 13
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE Adjusts the brightness of the screen. BRIGHTNESS P I C T U R E Adjusts the contrast of the screen. CONTRAST GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images.
Page 14
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description POSITION P O S I T I O N Adjusts the screen image left and right. HORIZONTAL Adjusts the screen image up and down. VERTICAL MENU : Exit : Decrease : Increase SET : Select another sub-menu TRACKING...
Page 15
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description SETUP S E T U P LANGUAGE To choose the language in which the control names are displayed. To adjust position of the OSD window POSITION on the screen. S E T U P If the output of the video card is WHITE...
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. Is the power indicator •...
Troubleshooting Display image is incorrect Display Position is • Press the AUTO/SET button to automatically incorrect. adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display.
Troubleshooting Display image is incorrect The screen color is • Check if the signal cable is properly connected mono or abnormal. and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. •...
Specifications Preset Modes (Resolution) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 720 x 400 31.468 640 x 480 31.469 640 x 480 37.500 VESA 800 x 600 37.879 VESA 800 x 600 46.875 1024 x 768 VESA 48.363 VESA 1024 x 768 60.123...
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. Place the monitor with its front facing downward on a soft cloth. Separate the stand using a screwdriver as shown in the picture. Install the Wall mount plate.
Need help?
Do you have a question about the L224WS and is the answer not in the manual?
Questions and answers
how to contact the service provider to change the display of L224WS
The manual advises checking the label attached to the product and providing the information to your dealer when requesting service. If the power cable is faulty, contact the manufacturer or the nearest authorized repair service provider for a replacement.
This answer is automatically generated