Advertisement
3
Raise Center of Tent
– Assemble center adjustable poles
(red sticker, longer poles). Pole should be initially
adjusted to the inner most hole "A". (illus. 7)
– Insert square end of brace poles into curved roof
poles and raise tent upright. (illus. 5, 6, 7)
– Adjustable poles should attach to squeeze
pins at bottom of tent. (illus 8)
– Repeat for other center adjustable pole.
illus. 7 Poles should be initially
adjusted to the inner most hole "A".
4
Raise Sides of Tent
– Assemble shock-corded adjustable end poles.
– Insert brace poles into end curved roof poles.
MAKE SURE when attaching the brace poles to
the curved poles that the bottom of the brace pole
naturally points down and toward the center of the
tent. (illus. 9)
– End poles should attach to squeeze
pins at bottom of tent. (illus. 8)
– Drape rainfly over tent and attach "S"
hooks on rainfly into holes in brace
poles. (illus. 9)
– Assemble and insert (short) Vertical
Hinged Door Pole through vertical sleeve
and into bottom pole stop. Gently apply
pressure to insert top end into top pole stop
and zip sleeve closed. (illus. 9, 10)
– Assemble and insert (long) Hinged Door
Pole through curved door sleeve and into
top pole stop. Gently apply pressure to insert
bottom end into bottom pole stop and zip
sleeve closed. (illus. 10, 11)
– Attach guylines to the ends of the
rainfly, 3 guylines at each end, and
stake out. (illus. 9)
Things You Should Know
•
Under certain conditions (cold weather, high humidity, etc.) condensation will form on
the inside surfaces of your tent. Condensation is caused by water vapor from your
breath, perspiration, or any wet clothing inside your tent. It is NOT LEAKAGE through the
tent fabric. It can be minimized by removing wet clothing from your tent and by
providing good ventilation through the tent.
•
Never store tent, even for a short period of time, without drying it thoroughly and
brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate
storage bag.
•
STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF. NEVER
PULL ON THE TENT FABRIC OR TENT STAKE LOOP TO REMOVE STAKE.
•
TENT POLES SHOULD NOT BE LEFT TELESCOPED
TOGETHER DURING STORAGE.
PRINTED IN CHINA
Rev. 11/07
Brace pole
Curved
poles in
pole sleeve
illus. 8
Insert squeeze
pin into pole
Brace pole with hole
for rainfly
"S" hooks
illus. 9
Tent shown completely
set-up. Note the different
angles of the end poles.
Vertical Door
Pole inserts
into sleeve
and zips in
illus. 10 Hinged Door
Pole Stop
•
Do not leave your tent set-up for weeks at a time, be aware that exposure to
the ultraviolet rays of the sun can seriously damage material and/or cause it to
become discolored.
WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM
THIS TENT FABRIC. This tent meets the flammability requirements
of CPAI-84. The fabric may burn if left in continuous contact with any
flame source. The application of any foreign substance to the tent
fabric may render the flame-resistant properties ineffective.
3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
illus. 6
When attaching the brace poles to
the curved poles make sure that the brace
poles naturally point straight down.
illus. 5
Shown with center
brace poles in position
Rainfly
Rainfly guylines
Stake down
doormat
illus. 11 Hinged Door
THE COLEMAN CO., INC.
MADE IN CHINA
and curved poles
through pole
sleeves.
End guylines
Long Door
Pole inserts
into sleeve
and pole
stops, then
zips in.
Advertisement
