Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for KL Industries Sun Dolphin Pro 120
Summary of Contents for KL Industries Sun Dolphin Pro 120
- Page 1 O w n e r ’ s M a n u a l Sun Dolphin Models: • Pro 120 Pro 102 Pro 94 1790 Sun Dolphin Drive Muskegon, Michigan 49444 phone 231-733-2725 231-739-4502 email klsales@klindustries.com website www.klindustries.com Big Bass Boat Features in a Compact Package...
-
Page 2: About Your Fishing Boat
PaPerwOrK warranty registration To properly register your boat with KL Industries for warranty validation please fill out the warranty registration form Photo #1 Serial Number online at www.klindustries.com. Please review our full warranty statement. If you are unable to register your boat Location online please contact our Customer Support Department at 231-733-2725. - Page 3 Manufacturer’s statement of Origin (MsO) Each boat comes with a document called a Manufacturer’s Statement of Origin (MSO). Think of it like the title to your car. It’s your proof, along with your sales receipt, of ownership. You’ll need both the MSO completed and signed by the retailer and your sales receipt to register the boat with your state licensing bureau.
- Page 4 Installing the seats Follow seat installation instructions provided with seats. Installing Drain Plugs Just like any boat, your boat may take on some water. Because of its flexible nature, a polyethylene boat is prone to accumulate a small amount of water between the deck and hull. Water may accumulate between the deck and hull due to rain, waves and condensation. This is normal, not a defect, and should be drained after use.
- Page 5 You will also need oars, which are available from KL Industries. Please call our Customer Support Department or order online www.klindustries.com. Mounting a small Outboard Motor If you wish to use an outboard motor, attach it to the transom following the instructions provided with the motor. Do not mount a motor with a horsepower rating higher than the rating on the boat capacity plate.
- Page 6 eleCTrICal sYsTeMs OVerVIew navigation lights If you operate the boat after dusk or before dawn you must have navigation lighting that meets US Coast Guard standards. If you are anchored or not moving only the stern light (sometimes called an all around light) should be on. If the boat is moving or underway both the bow lights and stern light must be on.
-
Page 7: Installing Accessories
InsTallInG aCCessOrIes Fish Finders/Depth Finders Pro 94 and Pro 102 Models 1. Hook up power for the fish finder or other accessories. The power will need to be connected directly to the battery. since this is not a fused connection, please see the installation instructions included with the fish finder. 2. -
Page 8: Operating The Boat
• Check and tighten if necessary all motor mounting clamps. • When loading, distribute the weight of fuel tank, battery, tackle boxes etc. evenly across the boat so that it will sit reasonably level in the water. Remember this is a small boat and extra caution should be taken to prevent overloading the craft as this could result in unsafe operating characteristics. - Page 9 navigation lights (available on Pro 102 and Pro 120 models) The lights should always be used if there are poor lighting conditions, e.g. dusk, dawn, fog etc. If you are anchored or not moving only the stern light (sometimes called an all around light) should be on. If the boat is moving or underway both the bow lights and stern light must be on.
-
Page 10: Care And Maintenance
significantly reduce performance. • Do not wind the winch too tight. Just enough to snug it against the winch stop is adequate. Over tightening may distort the bow over time. • Loosen the transom or gunwale tie down straps if the boat will be left on the trailer for more than 1-2 days. If the straps are left tight the boat may distort under pressure. - Page 11 Please Choose Your Model sTOraGe • Remove the boat from the water. Leaving the boat in the water Pro 120 for any longer than a few days will promote algae growth on Battery compartment the hull. Aerated Two padded livewell •...
- Page 12 Please Choose Your Model Pro 94 Pro 102 Twin padded swivel Twin swivel fishing chairs fishing chairs Livewell with aerator Livewell with drain Trolling motor plug-in socket Bow navigation light Thru-transom drain Battery box (battery not included) Battery compartment (battery not included) Built-in trolling Mooring Cleat Built-in trolling...
- Page 13 *Please have serial number available when ordering PrO 120 11774 Rub Rail Assembly 27’ 12572 Battery Strap w/holder 12006 Rivet (need 14) 12021 Rivet for Battery Strap (need 4) 12036 Rivet Burr for Rivet (need 14) 11382 Carpet Green per Yard 12247 Motor Mount Plate Rear 11348...
- Page 14 *Please have serial number available when ordering PrO 94 PrO 102 Requires 50 amp fuse. 12676 Trolling Motor Receptacle 12676 Trolling Motor Receptacle Female receptacle on boat (bow and stern) Female receptacle on boat (bow and stern) 12675 Trolling Motor Plug 12675 Trolling Motor Plug Male receptacle on motor...
- Page 15 KL Industries, Inc. warrants to the original owner of any KL Industries boat. Any part of the boat that is defective in material or workmanship will be repaired, without charge, at the purchasers’ local dealer or at KL Industries.
- Page 16 OPTIOnal aCCessOrIes Item Description Model Mooring Cover Cover gives years of protection shielding out rain and debris. The elastic cord gives a snug, tight fit. Pro 120 - #11238 Made of durable water resistant polyester fabric. Cover is supported by seats with backs folded Pro 102 - #ABT102CVGY down and by an adjustable center support pole (Pro 120 only) to eliminate puddling.