Subscribe to Our Youtube Channel
Summary of Contents for Eusso UVE7314-M
- Page 1 Ethernet over VDSL2 4-Port Managed Access Multiplexer UVE7314-M User Manual Rev. 1.1 Copyright EUSSO Technologies, Inc. All rights reserve...
- Page 2 The information in this document has been carefully checked and is believed to be correct as of the date of publication. EUSSO Technologies, Inc. reserves the right to make changes in the product or specification, or both, presented in this publication at any time without notice. EUSSO assumes no responsibility or liability arising from the specification listed herein.
- Page 3 Quick Installation Guide Step 1: Broadband Router Connections for UVE7314-M A. Connect UVE7314-M Giga Ethernet port to Broadband Router as the following connection. B. Connect Notebook PC LAN port to Broadband Router LAN port. C. Connect UVE7314-M RJ11 PHONE port to a Telephone Set or POTS Line.
- Page 4 Step 2: Settings for UVE7314-M from PC Web Browser A. UVE7314-M address is default at 192.168.168.168. Make sure the Notebook PC LAN port is within the same network and with IP address, e.g. 192.168.168.167, and Netmask of 255.255.255.0. B. Enter the IP address 192.168.168.168...
-
Page 6: Table Of Contents
Contents 1. Introduction....................5 2. Features ....................... 6 3. Specifications ..................... 7 4. LED Indicators & Reset Button.............. 8 5. Web-based Interface ................. 9... -
Page 7: Introduction
The UVE7314-M can be easily configured through web-based management interface. The intelligent web-based management allows for streamlined configuration of the UVE7314-M through a single IP address. The UVE7314-M can be configured on a per-link basis for transmission mode, rate limitations, and signal-to-noise (SNR) margin. -
Page 8: Features
2. Features 4 full-duplex VDSL links via RJ-11 connectors 4 corresponding POTS/ISDN lines via RJ-11 connectors Build-in POTS/ISDN worldwide standard splitter for each VDSL port Gigabit Ethernet for uplink Flexible MIB configuration of network resources via web-base interface or command line interface Supports VDSL MIB RFC-3728 standard Supports VDSL MCM MIB RFC-4070 standard Selectable fast and interleaved mode... -
Page 9: Specifications
3. Specifications Board dimension: 208mm x 320 mm Power supply: 110/220 VAC Power consumption: 30 Watt maximum. Interface: RJ-11 female Phone Jack RJ-45 female Ethernet jack Up-Link Port: Full Gigabit Ethernet support with auto MDIX. Phone: Industry standard phone jack with on board surge protection. Splitter: Fit for most common standards (US, EU, Japan, or China) Standard: Full ITU-T G.993.1 (VDSL) and G.997.1 compatible. -
Page 10: Led Indicators & Reset Button
4. LED Indicators & Reset Button On the front panel of UVE7314-M , there are 12 LED indicators as the following POWER: “Green On” indicates power is on and normal. ACT: “Green On” indicates Up-Link Ethernet port is in connection. -
Page 11: Web-Based Interface
5. Web-based Interface Use IE explore and type “http://192.168.168.168” (default setting IP address is 192.168.168.168) to access the web-based management. The default account name and password are “admin”, and “@admin@”. LAN Setting LAN setting can be changed manually by configuring the IP address settings in the blank space for the HOPE module... - Page 12 MIB Monitor MIB Monitor allows users to monitor all the useful MIB information, and can be plotted into a statistic diagram or table for engineering purposes. The MIB data is able to be collected every 15 minutes or daily by selection, and can be kept for 1 month. Port Status Port status shows the current connection status for each port, and all the port settings can be easily viewed with this status table.
- Page 13 Port Setting User can configure fast/interleave mode, downstream rate limit, upstream rate limit and SNR margin for each port in the port setting section. VLAN Setting VLAN setting allows different VLAN mapping for each DSL port connection.
Need help?
Do you have a question about the UVE7314-M and is the answer not in the manual?
Questions and answers