Table of Contents
Advertisement
Quick Links
IDSL / Broadband Access ROUTER
TAINET COMMUNIC ATION SYSTEM CORP.
Headquarters:
No. 25, Alley 15, Lane 120,
Sec. 1. Nei-Hu Rd,
Taipei 114, Taiwan
TEL: 886-2-26583000
FAX: 886-2-26583232
V1.3
TAINET
WANpro 2000i
USER'S MANUAL
The Professional Partner
09004-00018
Beijing Branch:
3F, A Building, 113 Zhi Chun Lu,
HaiDian District, Beijing, China
Zip Code: 100086
TEL: 86-10-62522081~87
FAX: 86- 10-62522077
2004/03/24
Advertisement
Table of Contents
Related Manuals for Tainet WANpro 2000i
Summary of Contents for Tainet WANpro 2000i
- Page 1 TAINET WANpro 2000i IDSL / Broadband Access ROUTER USER'S MANUAL The Professional Partner TAINET COMMUNIC ATION SYSTEM CORP. Headquarters: Beijing Branch: No. 25, Alley 15, Lane 120, 3F, A Building, 113 Zhi Chun Lu, Sec. 1. Nei-Hu Rd, HaiDian District, Beijing, China...
-
Page 2: Copyright © 1999 Tainet Communication Corporation
Tainet Communication Corporation. TAINET is a registered trademark, and “WANpro 2000i” is a trademark of Tainet Communication Corporation. Other product names mentioned in this manual are used for identification purposes only and may be trademarks or trademarks of their respective companies. -
Page 3: Fcc Notice
FCC NOTICE This equipment has been tested to comply with limits for a digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 4: Warranty And Service
You might use one of the following methods.. Via the Internet: visit our World Wide Web site at http://www.tainet.net Via the Sales Representatives: No. 25, Alley 15 Lane 120, Sec. 1. N u Rd. -
Page 5: Preface
Ethernet network. Your WANpro 2000i is easy to install and to configure via front panel for simple function or full functions of WANpro configurable via the TCS (Terminal Configuration Syetem) interface. -
Page 6: Specifications
Specifications Software (RFC 1661, RFC 1662) Frame Relay Multi-protocol Interconnect over Frame Relay (RFC 1490) HDLC packet-based format link layer, Three generally implemented specification of Local Management Interfaces (LMI) ANSI T1.617 Annex D CCITT (ITU-T) Q.933 Annex A LMI (Frame Relay Forum implementation agreement) The eight multi-connection of virtual link by Data Link Connection Identifier (DLCI) at the most, and Permanent Virtual Circuit (PVC) only Routing... -
Page 7: Lan Interface
Hardware LAN Interface Ethernet 10 Base-T (RJ-45) WAN Interface Provides various DTE interface module (DB-25) Synchronous and Asynchronous data format The DTE interface Module include V.35 speed up to 1Mbps (Sync) X.21 speed up to 1Mbps (Sync) EIA-530 speed up to 1Mbps (Sync) RS-232 speed up to 128Kbps (Sync) RS-232... - Page 8 Physical Dimensions: 48 x 180 x 262mm (Height x Width x Depth) Weight: 0.9kg Power Requirements Internal power suppory AC voltage: 90~265V Frequency: 47~60Hz 10 Watt maximum Operating Environment Temperature: 0ºC to 50ºC Humidity: 5% ~ 95%, non-condensing...
-
Page 9: Table Of Contents
WARRANTY AND SERVICE INFORMATION........錯誤! 尚未定義書籤。 PREFACE ............................ IV SPECIFICATIONS........................V CONCENT..........................VIII 2000 ..............1 HAPTER ETTING TO KNOW Unpacking......................2 Feature of the WANpro 2000i ................3 2000 ............... 4 HAPTER PPLICATION FOR THE Internet Access....................5 LAN-to-LAN......................6 Redundant......................7 ............ 8... - Page 10 4.5.5 Diagnosis Menu....................28 IDSL & WAN ................. 29 HAPTER CONFIGURATION IDSL & WAN Interface ..................30 Setting up the IDSL PPP link................31 Setting up the WAN PPP link................33 Frame Relay Setup.................... 35 5.4.1 Encapsulation....................35 5.4.2 DLCI......................... 35 5.4.3 LMI........................
-
Page 11: Chapter 1 Getting To Know Wanpro 2000I
Chapter 1 Getting to know WANpro 2000i This Chapter describes the key features of the WANpro. This chapter contains the following sections: Unpacking Feature of the WANpro 2000i... -
Page 12: Unpacking
1.1 Unpacking The components that you might have. ! TAINET Products Documentation Set CD ! The digital interface for WAN (Optional) ! Power cord ! RJ-45 cable (For Console port adapter) ! RS-232 (DB25 - RJ45) adapter (For Console Port) -
Page 13: Feature Of The Wanpro 2000I
1.2 Feature of the WANpro 2000i Your WANpro is packed with a number of features that give it the flexibility to provide a complete networking solution for small and medium size businesses, or remote offices. ! Ease to Install Your WANpro is designed for quick, intuitive and easy installation. Physically, its compact size and lightweight make it easy to position anywhere in your busy office. -
Page 14: Chapter 2 Application For The Wanpro 2000I
Chapter 2 Application for the WANpro 2000i This chapter shows the typical applications of the WANpro 2000i. This chapter contains the following sections: Internet Access LAN-to-LAN Redundant... -
Page 15: Internet Access
Internet ATM Switch Network CSU/DSU IDSL WANpro 2000i Edge Router DSLAM Ethernet For SOHO (Small Office/Home Office) environment, your WANpro offers the NAT feature that allows multiple users on the LAN (Local Area Network) to access the Internet concurrently for the cost effective solution. -
Page 16: Lan-To-Lan
2.2 LAN-to-LAN You can use the WANpro 2000i to connect two geographically dispersed networks over the IDSL line. Typical LAN-to-LAN applications for your WANpro are shown as follows. Lease Line WANpro 2000i WANpro 2000i Corporate LAN Branch Office LAN Usually WANpro 2000i act as NTU (Network Terminal Unit) when they are connected via a Frame Relay Network. -
Page 17: Redundant
Either a lease line or dialup, Auto Backup function guarantee the connection to protect through DSL line, dial up modem or ISDN T/A and ensure Internet connectivity is always available for LAN user and LAN-based Internet servers. Internet WANpro 2000i ATM Switch Network DSLAM... -
Page 18: Chapter 3 Configure And Monitor Via Front Panel
Chapter 3 Configure and Monitor Via Front Panel This Chapter describes the physical features of the WANpro and how to make the cable connections. This chapter contains the following sections: Front Panel Structure Front Panel LEDs Indicators Rear Panel Structure Front Panel Operation 3.4.1 Keypad and Cursor Control 3.4.2 LCD Menu Tree... -
Page 19: Front Panel Structure
3.1 Front Panel Structure The front panel of the WANpro 2000i contains LCD Screen, LEDs Signal Indicators and Keypads. The whole figure of the WANpro 2000i front panel could be found in the Figure 3.1A. Figure 3.1A Front Panel of the Tainet’s WANpro 2000i 3.2 Front Panel LEDs Indicators... -
Page 20: Rear Panel Structure
3.3 Rear Panel Structure The Rear panel of the WANpro 2000i includes power, switch, and some interface ports for the purposes of the network connection. The whole figure of the WANpro 2000i Rear panel could be found in the Figure 3.1B. -
Page 21: Lcd Menu Tree
3.4.2 LCD Menu Tree & Sync - External WANpro 2000i & Async - 115200 MAIN MENU IP A d d re s s & Async - 38400 & Async - 19200 IP N e tm a s k LAN Setup &... -
Page 22: The Description Of The Lcd Configuration
"Sync - External". Protocol Select WANpro 2000i supports PPP and Frame Relay, This parameter identifies which protocol of WAN and IDSL port is used, Frame Relay mode can only be work at alternative WAN or IDSL but not both. -
Page 23: Routing Table
Routing Table Default Gateway In this field, enter the IP of the remote node that is the gateway for the static route. Device Control Use this field to reload the parameter, this is require when any value Warm Start in LAN Setup, WAN Setup and IDSL Setup has been modified. Restore Default will restart the system and restore the factory This field... - Page 24 Remember to warm start your WANpro if you have changed the setting of any parameters under LAN Setup, WAN setup and IDSL setup. Each sub-menu contains the individual selectable items. Some of the sub-menu trees might be changed and come after later version. User could download the updated software through Tainet’s Internet Web site. http://www.tainet.net/tech/upgrade_fam.htm...
-
Page 25: Chapter 4 Installation & Initial Setup
Chapter 4 Installation & Initial Setup This chapter helps you to understand an organization of TCS (Terminal Configuration System) and connecting of the console port. This chapter contains the following sections: Configuring the WANpro from a PC. Power on your WANpro Navigation the TCS Interface Change the System Password. -
Page 26: Configuring The Wanpro From A Pc
PC COM port RJ-45 to RS 232 Console port WANpro 2000i NOTICE: You can access TCS (Terminal Configuration System) through a Telnet connection, when you have your WANpro LAN IP setup, to setup of LAN please refer to... -
Page 27: Power On Your Wanpro
When you power on your WANpro, it performs several seconds to internal tests, after it ready, screen will shows “Press [ENTER KEY] return to menu.”, you can now press [ENTER] to the login screen. !!! Welcome to Access TAINET WANpro 2000i !!! Please Enter Password : ž` Step 2. -
Page 28: Navigation The Tcs Interface
4.3 Navigation the TCS Interface The TCS (Terminal Configuration System) is the interface that you use to configure your WANpro. Several operations that you should be familiar with before you attempt to modify the configuration. Operation Description Move down to sub-menu [ENTER] To access in to a submenu. -
Page 29: Change The System Password
The passwords are separate to two-part “Console” and “Telnet”. To change the System Password, enter to the Configuration menu and selected Security, and there are two submenus under Security selected System security. Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System... -
Page 30: Organization Of Tcs Menu Tree
The TCS (Terminal Configuration System) is an user friendly configure interface, to use TCS you can configuring and monitoring the WANpro for the advanced management. The following diagram will help you easy to understand the TCS Organization menu. 4.5.1 Main Menu WANpro 2000i Configuration Monitoring Device Control... -
Page 31: Configuration Menu
4.5.2 Configuration Menu Configuration Routing Table System Security Interface System: System System Function DHCP Server SNMP Agent Fixed leases address map You can active the DHCP server and SNMP agent in this menu. Interface: Interface IDSL Encapsulate Data mode RIP Encapsulate Encapsulate NTU mode Sync... -
Page 32: System Security
PPP and Frame Relay encapsulation with WAN and IDSL serial interface and Ethernet setup of LAN interface. Routing Table: You can add the default route and static routes in this option. Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System Interface... -
Page 33: Monitoring Menu
Routing Table ARP Table DHCP Table Statistics System Sys t e m Address LAN WAN Status IDSL System: Monitoring TAINET WANpro 2000i Version 3.00 ================================================================================ [System] Interface Routing Table ARP Table DHCP Table Statistics View System Function System Function DHCP Server... - Page 34 Interface: Monitoring TAINET WANpro 2000i Version 3.00 ================================================================================ System [Interface] Routing Table ARP Table DHCP Table Statistics View Interface Status Iface Link Encapsulate S-Ver R-Ver Ethernet disable ----- ----- down disable ----- ----- IDSL down Passive RIP-1 RIP-1&2 Monitoring TAINET WANpro 2000i Version 3.00...
- Page 35 R: the route was established from RIP information. S: The route is a static route. The metric represents the cost of transmission for routing purposes. ARP Table: Monitoring TAINET WANpro 2000i Version 3.00 ================================================================================ System Interface Routing Table [ARP Table]...
-
Page 36: Dhcp Table
DHCP Table: Monitoring TAINET WANpro 2000 Version 3.00 ================================================================================ System Interface Routing Table ARP Table [DHCP Table] Statistics View the Dynamic leases of DHCP IP Address Ethernet Address Lease Time Remaining Lease Time 172.16.5.97 0080C8490738 1200 172.16.5.98 0050BA1D2BE5 1200 172.16.5.99... -
Page 37: Device Control
4.5.4 Device Control Device Control Warm Start Restore Default There are two options under device control menu: Warm Start: This command will causes the system restart and reloads the parameter, it also interpreter the WAN and IDSL connection. Restore Default: This command will restart the system and restore the factory default parameters. -
Page 38: Diagnosis Menu
4.5.5 Diagnosis Menu Diagnosis Ping Information There are two submenus include in diagnosis menu, Ping and Information. Ping: Diagnosis TAINET WANpro 2000i Version 3.00 ================================================================================ [Ping] Information IP Connectivity Host Reachability Target IP Address [172.16.5.41 Datagram Size [100 Timeout in Seconds PING 172.16.5.41 with 100 bytes of data... -
Page 39: Chapter 5 Idsl & Wan Configuration
Chapter 5 IDSL & WAN configuration This chapter helps you setup your IDSL and WAN link of WANpro with it PPP and Frame Relay connection. This chapter contains the following sections: IDSL & WAN Interface Setting up the IDSL PPP link Setting up the WAN PPP link Frame Relay Setup 5.4.1 Encapsulation... -
Page 40: Idsl & Wan Interface
5.1 IDSL & WAN Interface You can tread your WANpro 2000i as two serial ports device, which are IDSL interface and WAN interface. Depend on the network scheme you can elasticity to use both or either one. The IDSL port operates full duplex over twisted pair, 2-wire unconditioned lines, and operates at data rates 64 kbps or 128 kbps. -
Page 41: Setting Up The Idsl Ppp Link
Information is the frame contains control and response commands, however. HDLC supports full-duplex transmission, in which data is transmitted in two directions at the same time, resulting in higher throughput. HDLC is suitable for point-to-point and multipoint (multidrop or ne-to-many) connections. Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System [Interface]... - Page 42 10.0.0.2/30 WANpro 2000i WANpro 2000i IDSL-NT Mode IDSL-LT Mode Pair Copper Wire The above diagram shows the IDSL PPP link, configuration of your WANpro 2000i could be like follow. Site A (10.0.0.1/30) Site B (10.0.0.2/30) NTU mode Data Rate 128 k...
-
Page 43: Setting Up The Wan Ppp Link
5.3 Setting up the WAN PPP link Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System [Interface] Routing Table Security Interface Configuration Interface Name Data Mode [Sync ] Encapsulate [PPP [disable] Status down Press: SPACE to select TAB,ENTER:next field '<':left '>':right ESC:abort At WAN Interface you allow to configure the WAN port data mode and PPP encapsulate. - Page 44 10.0.0.2/30 CSU/DSU CSU/DSU WANpro 2000i WANpro 2000i Modem Modem The above diagram is the WAN PPP link, configuration of your WANpro 2000i could be like follow. Site A (10.0.0.1/30) Site B (10.0.0.2/30) Data mode Sync Data mode Sync Encapsulate Local IP 10.0.0.1...
-
Page 45: Frame Relay Setup
5.4 Frame Relay Setup Configuring Frame Relay on a WANpro includes the mapping of IP addresses to DLCIs and telling the router which virtual circuits are connected. Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System [Interface] Routing Table Security Interface Configuration... -
Page 46: Manipulation Frame Relay Via Wan Or Idsl
5.4.4 Manipulation Frame Relay via WAN or IDSL Your WANpro 2000i allow only one serial port to act Frame Relay encapsulation, either WAN port or IDSL port, but not both. Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System [Interface] Routing Table... - Page 47 Manipulation Frame Relay Frame Relay Switch via IDSL Interface WANpro 2000i Fra me Re la y Frame Relay Switch Ne twork IDSL device Frame Relay Switch WANpro IDSL device Frame Relay 2000i Switch Manipulation Frame Relay Frame Relay Switch via WAN Interface WANpro 2000i CSU/DSU...
-
Page 48: Chapter 6 Lan And Routing Access Configuration
CHAPTER 6 LAN and Routing Access Configuration This chapter shows you how to configure the LAN as well as the WAN of your WANpro for Internet access. This chapter contains the following sections: Ethernet Setup RIP Setup DHCP Setup Configuring Static Routes & Default Routes 6.4.1 Configuring Static Routing Table 6.4.2 Configuring Default Gateway... -
Page 49: Ethernet Setup
6.1 Ethernet Setup You can have TCP/IP setup for your WANpro at LAN Interface menu. Configuration TAINET WANpro 2000i Version 2.99t ================================================================================ System [Interface] Routing Table Security Interface Configuration +-------------Encapsulate--------------+ | Interface Name | Encapsulate Ethernet | Ethernet MAC 0090BB000022 | Local IP Address [192.168.0.254... -
Page 50: Rip Setup
Configuration can be performed on a per-interface basis. You can enable or disable RIP for each interface, WAN, IDSL and LAN. The following table describes the RIP option of your WANpro. Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System... -
Page 51: Default Route
Mode: The interface can execute passive or active RIP. When executing passive RIP, the interface revises its routing table based on the routing update information it receive, but does not advertise self-routing information to other routers. When configured for active RIP at specifies interface acts as a full router;... -
Page 52: Dhcp Setup
DNS server and WINS server. Enable Fixed Leases Address Map allow you to assign up to 8 permanent IP leases to clients by elling the client's NIC (Network Interface Card) Ethernet Address (MAC address). Configuration TAINET WANpro 2000i Version 3.00 =============================================================================== System]... - Page 53 Field Description Default Lease Time (Secs) This field specifies an IP address lease time for clients. It is base on seconds and the default value is 38400 (10 hrs). Gateway Those fields specify an IP default gateway, DNS server and WINS server to Windows 95/98, Windows NT and DNS Server other systems that support the DHCP client.
-
Page 54: Configuring Static Routes & Default Routes
Network B Network C Router 1 WANpro 2000i Router 2 Configuring static routes and default gateway can be finding in Configuration Routing Table menu. Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System Interface [Routing Table] Security Routing Table Configuration +----------Routing Table-----------+ |<Static Routing>... -
Page 55: Configuring Static Routing Table
6.4.1 Configuring Static Routing Table Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System Interface [Routing Table] Security Routing Table Configuration Destination NetMask Nexthop Metric 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0... -
Page 56: Configuring Default Gateway
If the next router doesn't know the necessary route, it sends the packet to its own default gateway, and this process continues on until the destination network is reached. Configuration of default gateway is performed under Configuration Routing Table. Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System... -
Page 57: Chapter 7 Nat & Ip Filter
Chapter 7 NAT & IP Filter This chapter shows you how NAT work with your WANpro and discusses the function of IP filter. This chapter contains the following sections: NAT Setting IP Filter Setting... -
Page 58: Nat Setting
Internet and must be properly registered so information can be sent to them. Configure of NAT can be find under the Configuration Security - Traffic Security menu. Configuration TAINET WANpro 2000i Version 3.01 ================================================================================ System... - Page 59 192.168.1.2 ~ 192.168.1.23 192.168.1.1 (LAN I/F) Inte rne t Private IP use in this LAN segment is 192.168.1.0/27 FTP Server 192.168.1.24 WANpro 2000i IDSL PPP Link ISP Router Web Server IDSL Device 192.168.1.25 IDSL IP : 10.0.0.2/30 Serial IP : 10.0.0.1/30 168.192.0.2 ~ 168.192.0.6...
- Page 60 Step 1. Selected the public IP for PAT Choose one IP between 168.192.0.1 ~ 168.192.0.6 for PAT. The NetMask should match to the network segment that ISP assigns to you. +-----------------------------NAT------------------------------+ | Static NAT (Network Address Translation) [enable ] | NAPT (Network Address Port Translation) Public IP [168.192.0.1 NetMask...
- Page 61 Step 3. Configuring the Static NAT Assign the remaining public IP to the workstation or server in your LAN. +-Static NAT (Network Address Translation)--+ Public IP Private IP 168.192.0.2 192.168.1.26 168.192.0.3 192.168.1.27 168.192.0.4 192.168.1.28 168.192.0.5 192.168.1.29 168.192.0.6 192.168.1.30 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0...
-
Page 62: Ip Filter Setting
WAN or IDSL alternative. To enable the IP Filter can be find under Configuration Security - Traffic Security. There has filter table for each incoming and outgoing filter, this allow you to configure specifies IP traffic that are permitted to access your LAN. Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System Interface... -
Page 63: Chapter 8 Snmp Configuration
Chapter 8 SNMP Configuration This chapter discusses SNMP (Simple Network Management Protocol) for network management and monitoring. This chapter contains the following sections: About SNMP Configuring SNMP... -
Page 64: About Snmp
[WANpro 2000i | System Location [Taipei +-----------------------------------------------------+ Press: ASCII, SPACE, BS, DEL TAB,ENTER:next field '<':left '>':right ESC:abort WANpro 2000i so far only provides "GET" value with SNMP, and Get Community is as default "public", this is simply SNMP terminology for password. -
Page 65: Chapter 9 System Maintenance
Chapter 9 System Maintenance This Chapter covers the diagnostic method that help you to maintain your WANpro. This chapter contains the following sections: System Status IDSL Local Loop Back Firmware Upgrade 9.3.1 Upload Router Firmware - Uploads from DOS mode 9.3.2 Upload Router Firmware - Upload from NT 4.0 Platform... -
Page 66: System Status
The detail of each field please refers to chapter 4.5.3 in this menu. 9.2 IDSL Local Loop Back Uses IDSL local loop back to diagnosis the loop characteristic and the device. Configuration TAINET WANpro 2000i Version 3.00 ================================================================================ System [Interface]... -
Page 67: Firmware Upgrade
9.3.1 Upload Router Firmware - Uploads from DOS mode Flasht.exe is the tool for user to upgrade the firmware, which can be use for the following TAINET product; CS-Jr, WANpro 2000, NMC32, NMC9000, and Router Module. This program can only be operated at pure 16-bit MS-DOS mode. - Page 68 02 - CS-Jr 03 - NMS9000 04 - Non-Channelize Router 05 - Channelize Router 06 - WANpro 2000i Step 4: Upload the firmware Press 3 "Selected Target Upload" to target the device, this menu will list the device that has been identify in your network on setup 2.
-
Page 69: Upload Router Firmware - Upload From Nt 4.0 Platform
NT4.0 which is call "NDIS 3.0 Packet Driver v3.5", Please following the instructions below to work out it. Files require: Download.exe (TAINET Network Device upload agent tools for NT4.0) wr_fxxx.bin (binary firmware, upload file) Oemsetup.inf (Protocol Driver for NT4.0) Packet.sys (Protocol Driver for NT4.0) - Page 70 Step 5: Start upgrade Running Upload agent by telling then the new firmware file and destination MAC address. Usage:download -f <file> -m <mac> <file> Specify the binary file for download. <mac> Specify the target MAC address. E.g. C:\download -f c:\temp\rm_f213.bin -m 3806b0 Step 6: Restart Restart the Device.
-
Page 71: Chapter 10 Troubleshooting
Chapter 10 Troubleshooting This chapter covers the potential problems you may run into and the possible remedies. After each problem description, some instructions are provided to help you to diagnose and to solve the problem. This chapter contains the following sections: 10.1 Problems Starting Up the WANpro 10.2 Problem with the IDSL Interface 10.3 Problems with the LAN Interface... -
Page 72: Problems Starting Up The Wanpro
10.1 Problems Starting Up the WANpro Problem Corrective Action None of the LEDs and LCD are on when you Check the connection between the AC adapter power on the WANpro and the WANpro. If the error persists, you may have a hardware problem. -
Page 73: Chapter 11 Interface Pinout List
Chapter 11 Interface PinOut List This chapter contains the following sections: 11.1 WAN Interface PinOut List 11.2 RS-232 adapter for Console Interface PinOut 11.3 IDSL Interface Pin Assignment... -
Page 74: Wan Interface Pinout List
11.1 WAN Interface PinOut List SIGNAL V.24/RS-232 V.35 EIA-530 INPUT SOURCE FUNCTION DB-25 (F) DB-25 (F) DB-25 (F) OUTPUT Protective COMMON ----- Ground Signal COMMON ----- Ground Transmitted 2 (TXD A) 2 (TXD A) OUTPUT Data 14 (TXD B) 14 (TXD B) Received 3 (RXD A) 3 (RXD A) -
Page 75: Idsl Interface Pin Assignment
11.3 IDSL Interface Pin Assignment 1 2 3 4 5 6 7 8 RJ-45 Signal Function Tip/Ring Tip/Ring...