Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Videotron E2050-ER1
Summary of Contents for Videotron E2050-ER1
-
Page 1: Remote Controls
U S E R ' S G U I D E Remote controls programming... -
Page 2: Table Of Contents
E2050-ER1 AND RT-U43CO REMOTE CONTROLS MODELS E2050-ER1 AND RT-U43CO BUTTONS........1 PROGRAMMING THE E2050-ER1 REMOTE CONTROL. -
Page 3: E2050-Er1 And Rt-U43Co Remote Controls
E2050-ER1 AND RT-U43CO REMOTE CONTROLS There are three remote controls for the digital terminals: the E2050-ER1, the RT-U43CO and the RC-U49C+. You can identify your model by examining the "5" key. • This key is oval on the E2050-ER1 and square on the RT-U43CO and RC-U49C+. -
Page 4: Programming The E2050-Er1 Remote Control
E2050-ER1 AND RT-U43CO REMOTE CONTROLS (CONTINUED) PROGRAMMING THE E2050-ER1 REMOTE CONTROL This step is not essential, but allows you to use the digital terminal remote control with your TV and VCR. How to Program the TV Mode Key 1. Turn on the TV set. -
Page 5: Programming The Rt-U43Co Remote Control
E2050-ER1 AND RT-U43CO REMOTE CONTROLS (CONTINUED) How to Identify Programmed Codes 1. Point the remote control away from the digital terminal , TV and VCR. 2. To identify the TV code, press and hold TV and SELECT at the same time until the LED on the remote blinks twice. - Page 6 E2050-ER1 AND RT-U43CO REMOTE CONTROLS (CONTINUED) How to Program the VCR Mode Key 1. Turn on the VCR or DVD player, then press and hold the VCR and SELECT keys until the LED stays lit. 2. Repeat the steps described under How to Program the TV Mode Key, substituting the VCR key for the TV key.
- Page 7 E2050-ER1 AND RT-U43CO REMOTE CONTROLS (CONTINUED) How to Program the Volume Control 1. Press and hold the CBL and SELECT keys at the same time until the LED stays lit. Press the VOL+ key, and then the CBL key. The LED will blink twice and go out.
-
Page 8: Rc-U49C+ Remote Control
RC-U49C+ REMOTE CONTROL These three remote controls have different programming procedures for their TV and VCR mode keys, as well as different VOD/VCR keys. It’s therefore important that you follow the instructions for your particular model. MODEL RC-U49C+ BUTTONS Selects device being On/off for each device operated. -
Page 9: Programming The Rc-U49C+ Remote Control
RC-U49C+ REMOTE CONTROL (CONTINUED) PROGRAMMING THE RC-U49C+ REMOTE CONTROL Point and Press ® Programming This method allows you to program the remote control without using codes. Instead, the remote control automatically finds the correct command that you select in a variety of codes until you find the code that operates your device. You then lock in the correct code as described below. - Page 10 RC-U49C+ REMOTE CONTROL (CONTINUED) Code Number Readback To identify the 3-digit setup codes stored under the Point and Press ® programming method, follow these steps: 1. For the TV code, press and hold the TV and SELECT keys at the same time until the TV button illuminates. 2.
- Page 11 RC-U49C+ REMOTE CONTROL (CONTINUED) ALL button Once you have programmed each of your devices, press ALL button to turn all of them on/off with a single button press. You can also program the ALL button to tune your TV to its correct output channel (usually 3). Programming the ALL Button 1.
- Page 12 RC-U49C+ REMOTE CONTROL (CONTINUED) Using M1, M2 buttons Using the programmed channels (previous page) as an example… 1. Press M1 Cable set-top terminal tunes to channel 001. 2. Press M1 again – Cable set-top terminal tunes to channel 012. 3. Press M1 again – Cable set-top terminal tunes to channel 123. 4.
- Page 13 RC-U49C+ REMOTE CONTROL (CONTINUED) How to Program the SmartKeys™ Your remote has two SmartKeys™ - CABLE and TV that operate in its cable mode. Each SmartKey™ can be programmed to transmit multiple functions. Programming and using the CBL SmartKey™ The CBL button normally turns on/off your cable set-top terminal. To program the CBL button to transmit multiple pre-programmed functions, follow the steps below: 1.
- Page 14 RC-U49C+ REMOTE CONTROL (CONTINUED) Mode Lock™ Your CheckMate ® IV remote can be set-up in two different operating modes - "locked" and "unlocked". From the factory, it is set in its "locked" mode, which means it will operate all the functions of your cable set-top terminal, plus a limited number of functions of your TV, VCR, DVD devices.
-
Page 15: At8400 Remote Control
AT8400 REMOTE CONTROL THE AT8400 ALLTOUCH® REMOTE CONTROL FUNCTIONS AS FOUR REMOTE CONTROLS IN ONE! Once programmed, it can control your TV, VCR, PVR, and any equipment connected to the AUX outputs. MODEL AT8400 BUTTONS Displays the Interactive Power ON/OFF Program Guide (IPG) The 4 mode keys Performs the... -
Page 16: Programming The At8400 Remote Control
AT8400 REMOTE CONTROL (CONTINUED) The steps described below are the same for each mode button. Repeat them for each device controlled by the remote, make sure you press the correct mode key for each device. PROGRAMMING THE AT8400 REMOTE CONTROL How to Program the TV Mode Key 1. - Page 17 AT8400 REMOTE CONTROL (CONTINUED) How to Identify Programmed Codes 1. Press and hold the SELECT key and the appropriate mode key (AUX, VCR, TV or CBL) until the mode key blinks twice. 2. Enter carefully the code 9 9 0. After each digit the mode key will blink once. At the end of the operation it should blink twice.
-
Page 18: List Of Codes
LIST OF CODES TV SETUP CODES Admiral – 107, 030, 061, 193, 056, 026, 054, 211 Inkel – 075, 364 073, 082, 062, 049, 056, 074, 119, 120, 254, 042, Advent – 072, 094, 425 Inteq – 031 052, 053, 054, 055, 069, 070, 416 Adventura –... -
Page 19: Vcr Setup Codes
LIST OF CODES (CONTINUED) VCR SETUP CODES Admiral – 062, 004l, 066, 075 JCL – 049, 086 Quarter – 060 Adventura – 014 Jensen – 055 Quartz – 060, 090, 238, 378 Aiko – 292 JVC – 081, 055, 006, 007, 026, 038, 060, 102, 120, Quasar –...