Electrolux EI27MO45GSA Installation Instructions Manual
Hide thumbs
Also See for EI27MO45GSA:
- Use & care manual (30 pages) ,
- Installation instructions manual (12 pages) ,
- Technical & service manual (52 pages)
Advertisement
Available languages
Available languages
Quick Links
iNSTALLATiON ANDSERVICE MUST BEPERFORMED BYA QUALIFIED iNSTALLER.
IMPORTANT: SAVEFORLOCALELECTRICAL I NSPECTOR'S USE.
READAND SAVETHESEINSTRUCTIONS FORFUTUREREFERENCE.
The electrical requirementsfor this oven are 115-120 voltsAC, 15 arnpsor larger.
iMPORTANT-PLEASE READANDFOLLOW
Before beginning,
please read these instructions
completely
and carefully.
Be sure to DISCONNECT THE PLUG of the microwave
oven from the electrical
outlet
before
installing
the built-in
trim kit.
Remove the turntable
from the oven cavity.
Because the kit includes
metal parts, caution
should
be used in handling
and installation
to avoid the possibility
of injury.
Do not remove permanently
affixed
labels, warnings,
or plates from the product.
This may void the warranty.
Please observe all local and national
codes and ordinances.
The installer
should leave these instructions
with the consumer
who should retain
for local inspector's
use and for
future reference.
PARTSINCLUDEDIN THEKITS
1) FRONTFRAMEASSEMBLY
QTY1
2) BOTTOM DUCT ASSEMBLY
QTY 1
Printed in United States
3) SCREW A (1 3A6"LENGTH)
QTY 2
4) SCREW B (1 3A" LENGTH)
QTY 4
Advertisement
Related Manuals for Electrolux EI27MO45GSA
Summary of Contents for Electrolux EI27MO45GSA
- Page 1 iNSTALLATiON ANDSERVICE MUST BEPERFORMED BYA QUALIFIED iNSTALLER. IMPORTANT: SAVEFORLOCALELECTRICAL I NSPECTOR'S USE. READAND SAVETHESEINSTRUCTIONS FORFUTUREREFERENCE. The electrical requirementsfor this oven are 115-120 voltsAC, 15 arnpsor larger. iMPORTANT-PLEASE READANDFOLLOW Before beginning, please read these instructions completely and carefully. Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before...
- Page 2 Provide an opening in the wall or cabinet as indicated by local code, and it is suggested that the local code be in Illustration 1. The depth should be a minimum of 20" checked for any such requirement. (50.8 cm). The floor of the opening should be constructed 2.
- Page 3 BOTTOM DUCTASSEMBLY Place the bottom duct in the opening and center. When Secure the Bottom Duct Assembly with the two (1 3A6") screwsA. IMPORTANT: Secure screws to the nside the Bottom Duct Assembly is in the opening correctly, the cabinet. See Illustration flange will be tight against the lower edge of the opening.
- Page 4 3. Push the position of the oven into the cabinet so that the Adjust the frame so that the gap around the top of the feet of the oven are fitted into the recesses of the Bottom door and frame is even. Pre-drill 4 holes using an Ys"...
- Page 5 LA INSTALACION Y ELSERVICI0DEBEN SERREALIZADOS P0R UN iNSTALADOR CALiFICAD0. IMPORTANTE: GUARDEPARAUS0 DELiNSPECTOR ELI_CTRIC0 LOCAL. LEA Y GUARDE ESTASINSTRUCCIONESPARA REFERENCIAFUTURA. Los requisilosei_ctricos de este homoson de 115-120 vollios de CA, 15 arnperioso rn_s. iMPOBTANTE - LEA Y SIGALASiNSTBUCCIONES Antes de comenzar, lea estas instrucciones completa y detalladamente.
- Page 6 Haga una abertura en la pared o en el gabinete como se exigirlo y se sugiere revisar en el c6digo local alguna indica en la ilustraci6n 1. La profundidad debe ser de un indicaci6n de ese tipo. mfnimo de 20" (50.8 cm). La superflcie de la abertura debe 2.
- Page 7 COHJUHTO DEDUCTOIHFERIOR Coloque el ducto inferior en la abertura y c_ntrelo. Cuando Asegure el conjunto del ducto inferior con dos tornillos el con junto de ducto inferior est_ colocado correctamente (1 3A6"). IMPORTANTE: Asegure los tornillos en el interior en la abertura, las bridas quedar_n firmes contra el borde del gabinete.
- Page 8 3. Empuje el horno dentro del gabinete para que las patas Ajuste el marco de modo que el espacio alrededor de la del horno encajen en las ranuras del conjunto de ducto puerta y el marco sea uniforme. Pre-taladre 4 agujeros inferior.
- Page 9 UN INSTALLATEURQUALIFli_DOlT PROCi':'DER A L'INSTALLATION ET AUX RI_PARATIONS. iMPORTANT" CONSERVERA L'USAGE D'UN INSPECTEUR EN I':'LECTRICiT[_ L OCAL. URE ET CONSERVERCES DiRECTiVES POUR R[_F[_RENCE FUTURE. L'aiirnentation6iectrique pource four est de 115-120 volts CA, 15 amperes et plus. iMPORTANT-PRiEREDELIREETDESUiVRE Pri_re de lire attentivement toutes ces directives avant de commencer.
- Page 10 Faire une ouverture dans lemur ou I'armoire comme lat6rales, arri_re et plafond); le code local pourrait I'exiger; indiqu_ _ I'illustrafion 1. La profondeur dok &tre au il est donc sugg_r_ de v_rifier ce point. minimum de 50,8 cm (20 po). Le plancher de I'ouverture 2.
- Page 11 ENSEMBLE DUCONDUITINFi RIEUR D'i VACUATION 1. Placerleconduitinf_rieurdansl'ouvertureetcentrer. 2. Fixerl'ensembleduconduitinf_rieuravecdeuxvisA Quand il est plac_ correctement, les brides seront (1 3A6po). iMPORTANT: Bien fixer les vis _ I'int_rieur serr_es contre la bordure inf_rieure de I'ouverture. Voir I'armoire.Voir Illustration Illustration VISA VlSA Illustration 2 Illustration 3 INSTALLATION DEL'APPAREIL Placer le four pros de I'ouverture...
- Page 12 3. Pousser le four dans I'armoire afin que ses pattes entrent Ajuster le chassis afin que I'espacement au sommet de la dans les _videments de I'ensemble du conduit inf_rieur porte et le chassis soit _ _galit_. Percer 4 avant-trous avec d'_vacuation.
- Page 13 INSTRUCCI(}NES DEINSTALACION INSTRUCCI(}NES DEINSTALACION DEL H(}RN(}MiCR(}(}NDAS DEL HORN(}MICR(}(}NDAS DiRECTiVES D'iNSTALLATi(}N DIRECTIVES D'INSTALLATI(}N DU FOURA IVlICR(}-(}NDES DU FOURA IVIICR(}-(}NDES CORRECTION page E2: Dimension D* CORRECTION page E2: Dimension D* 30" 18 ¼6" 2 sAC 13%" 153g '' min.30" 18 ¼6" 13%" 153g '' min.30"...