Download Print this page

GE RAVHW2 Installation Instructions Manual

Hide thumbs
   

Advertisement

TOOLS NEEDED
• Adjustable wrench
• Phillips head screwdriver
• Brazing equipment
• Piping solder or flux
.4,CAUTION:
Disconnect the electrical
power
supplg before installing.
Fll
Place the
Heater
the Vertical
Hydronic
onto
Zoneline by locating the four holes in its side
flanges over the four bolts on the top of the
Zoneline.
HL!dronic
heater
bolts
Zoneline
Locating
holes (_nd
bolts
F21 Attach
Hydronic Heater to
using
the
the Zoneline
6 screws.
,
31-61420
I
07-07 JR
I
B]
Connect the tubing.
There are two options: [] Standard Connection or
[] By-Pass Connection.
Choose the appropriate connection for your
installation requirements.
Standard Connection Option
Connect the 90 ° elbow to the upper outlet tube.
Connect the shut-off valve to the other end of the
90 ° elbow.
Shut-off
valve
90 °
elbow
tube
FB1 By-Pass Connection Option
Connect the long two-bend tube to the lower inlet
tube, turn it and connect it to the T-fitting in the
outlet tube. Connect the shut-off valve to the other
end of the T-fitting.
Shut-off
valve
T-fitting
two-bend
tube
Lower inlet
tube
Printed in Chino

Advertisement

   Related Manuals for GE RAVHW2

No related manuals

   Summary of Contents for GE RAVHW2

  • Page 1

    TOOLS NEEDED Connect the tubing. • Adjustable wrench • Brazing equipment There are two options: [] Standard Connection or • Phillips head screwdriver • Piping solder or flux [] By-Pass Connection. Choose the appropriate connection for your installation requirements. .4,CAUTION: Disconnect the electrical power supplg before installing.

  • Page 2

    Installation Instructions three-pin connector 14"1 Connect the from the Hgdronic Heater to the three-pin connector on the Zoneline. Three-pin connectors connect I-'S1 Run and the !0" round duct Hgdronic Heater. 10" round Move the actuator switch to the OPENposition. Actuator Reconnect electrical power.

  • Page 3

    OUTILLAGE NECESSAIRE Raccordez la tugauterie. • CI_ _ molette • Equipement de brasage IIexiste deux options: [] Raccordement normalou • Tournevis cruciforme • Brasure ou flux de tugauterie [] Raccordement avecderivation. ¢hoisissez le raccordement appropri_ aux conditions requises de votre installation. :D branchez ,'alimentation I kATTENTION...

  • Page 4

    Instructions d'installation connecteur 14--I Branchez le (_trois broches du g_n_rateur de chauffage central au connecteur trois broches du Zoneline. Connecteurs \ _]trois © \ broches 10 po Amenez raccordez le conduit fond de au g_n_rateur de chauffage central. Conduit ron de 10 po r61Enclenchez I'interrupteur en position OPEN.

  • Page 5

    HERRAMIENTAS NECESARIAS Conecte Io tuberfo. • Llove de tuercos • Equipomiento Hog dos opciones: [] Conexi6n normal o ojustoble de soldoduro [] Conexi6n derivodo. • Destornillodor de • Soldoduro de tuberfo EIUo Io conexi6n odecuodo poro sus requerimientos cobezo Phillips o fundente de instoloci6n.

  • Page 6

    Instrucciones de instalaci6n conector tres clavijas 14"-I Enchufe el del calentador hidr6nico al conector de tres clavijas del Zoneline. Conectores © \ de tres clavijas g conecte Extienda el conducto redondo de 10" al calentador hidrbnico. Conducto_ ''I/ redondo f de 10"...

  • Page 7

    Notas...

  • Page 8

    Notas...

This manual also for:

Ravhw3, Ravhw1

Comments to this Manuals

Symbols: 0
Latest comments: