Subscribe to Our Youtube Channel
Related Manuals for Si-tex GPU series
Summary of Contents for Si-tex GPU series
-
Page 1: Smart Dgps Waas Receiver
Smart DGPS WAAS Receiver "GPU series" ANUAL Smart DGPS WAAS Receiver "GPU series" UM code: MAGPUxx1AE, B290507... -
Page 2: Limited Warranty
Caution The Smart DGPS WAAS "GPU series" units are believed to be accurate and reliable, but they can be misinterpreted. For this reason we suggest that you read carefully this User Manual and make sure you understand with its contents before using the Smart DGPS WAAS "GPU series" units. For a safe navigation compare information received from GPS to all available navigation indications re- ceived from other electronic navigation navaids that you carry on board. -
Page 3: Table Of Contents
1.3 SOFTWARE INTERFACE ................9 1.4 MECHANICAL CHARACTERISTICS & MOUNTING WITH CONNECTOR ODEL 1.4.1 Installing ..................10 1.4.2 Dimensions ..................12 1.5 MECHANICAL CHARACTERISTICS & MOUNTING GPU M ..... ODEL 1.5.1 Installing ..................12 1.5.2 Dimensions ..................14 Smart DGPS WAAS Receiver "GPU series"... - Page 4 Smart DGPS WAAS Receiver "GPU series"...
-
Page 5: Smart Dgps Waas Receiver
Cable GPU with connector 8 pins female connectors 1.1.2 ELECTRICAL CHARACTERISTICS : 10 Vdc to 35 Vdc unregulated Input Voltage Power Consumption : 0.8 W max Electrical Interface : TTL voltage levels, RS-232 polarity Smart DGPS WAAS Receiver "GPU series"... -
Page 6: Performance
One of this limit can exceded but not both. 1.1.4 ENVIRONMENTAL CHARACTERISTICS Operating Temperature: 0° C~ +60° C Storage Temperature : -20° C~ +85° C Relative Humidity : 95% non-condensing Water Resistance : 100% waterproof Smart DGPS WAAS Receiver "GPU series"... -
Page 7: Wiring
The GPS products interface protocol design is based on the National Marine Electronics Association's NMEA 0183 ASCII interface specification. These stand- ards are defined in "NMEA 0183 Version 2.0" (for more information see NMEA, www..nmea.org). Smart DGPS WAAS Receiver "GPU series"... -
Page 8: Mechanical Characteristics & Mounting Gpu With Connector Model
1. Apply the adhesive mounting template sheet in the area that was verified to receive satellite signal well. 2. Then, following template instruction, drill a 0,95 inch (24 mm) hole and three 0,155 inch (4 mm) holes. Smart DGPS WAAS Receiver "GPU series"... - Page 9 3. Remove the template and let the cable go through the central hole. 4. Apply a small coat of RTV to the underside of the antenna. 5. Place the antenna and then screw it with the three M3 screws. Fig.1.4.1b - Installing GPS Antenna (III) Smart DGPS WAAS Receiver "GPU series"...
-
Page 10: Dimensions
This is of no concern however as the antenna must be tightened until the antenna stops rotating on the antenna mounting bracket. Smart DGPS WAAS Receiver "GPU series"... - Page 11 3. Remove the template and let the cable go through the central hole. 4. Apply a small coat of RTV to the underside of the antenna. 5. Place the antenna and then screw it with the three M3 screws. Smart DGPS WAAS Receiver "GPU series"...
-
Page 12: Dimensions
Fig.1.5.1b - Installing GPS Antenna (III) 1.5.2 DIMENSIONS Fig.1.5.2 - GPS Antenna Dimensions Smart DGPS WAAS Receiver "GPU series"...
Need help?
Do you have a question about the GPU series and is the answer not in the manual?
Questions and answers