Summary of Contents for Mobility Electronics Invision PS6S1800M
-
Page 1: User Guide
PS6S1800M Serial/Modem Charging Cradle User Guide Mobility Electronics, Inc 9918 Via Pasar, San Diego, CA 92126, USA (858) 880-2225 Phone: (858) 530-2733 Fax: www.invisioncradles.com... - Page 2 Mobility Electronics, Inc. assumes no responsibility for any damage or loss resulting from the use of this user guide. Mobility Electronics, Inc. assumes no responsibility for any loss or claims by third parties that may arise through the use of this product. Mobility Electronics, Inc.
-
Page 3: Table Of Contents
Serial/Modem Charging Cradle User Guide Contents ..................ONTENTS ..................1 NTRODUCTION Setting up the PS6S1800M................2 Product/Technical Support ................7 Appendix A – Regulatory Information ............11 Appendix B – Warranty................14 Mobility Electronics, Inc... -
Page 4: Introduction
Serial/Modem Charging Cradle User Guide Introduction The invision PS6S1800M serves as an essential data communications device, enabling you to synchronize the information on your Symbol® SPT 1700 or SPT 1800 terminal and the Palm Desktop software using HotSync® technology. It also charges both your terminal and a spare battery –... -
Page 5: Setting Up The Ps6S1800M
Mobility. HotSync Connection Before you prepare the PS6S1800M cradle for HotSync communications, you must decide which type of HotSync communication you desire. (1) HotSync with the computer, or (2) HotSync with a remote location. Mobility Electronics, Inc... - Page 6 It cannot share a port with an internal modem or other device. If you are unsure about the location of the serial port on your computer, refer to the user's manual supplied with the computer. Mobility Electronics, Inc...
- Page 7 RJ-11 end of the analog telephone cord that “used to be in the wall” (before step above) into the “Line- Out” jack on the back of the cradle. Set the Modem/Serial switch to Modem for modem operations. Mobility Electronics, Inc...
-
Page 8: Operating The Cradle
See the Product Reference Guide provided by the terminal manufacturer for more information on configuring the SPT terminal, computer, or remote location for HotSync operations. Mobility Electronics, Inc... - Page 9 Then gently press down on the battery to ensure proper contact. The Spare Battery Charge LED turns “RED” to indicate the battery is charging. The LED turns “GREEN” when the battery is fully charged (approximately 3 hours). Mobility Electronics, Inc...
-
Page 10: Product/Technical Support
Make sure it is firmly seated. Communications software is not installed, Perform setup as described by the terminal or is not configured properly. manufacturer. Modem/Serial switch is not set correctly. Check to be sure the Modem/Serial switch is set to Serial. Mobility Electronics, Inc... - Page 11 Modify init string in US/Canada to “AT&F\N5” in an electrically noisy environment. forcing MNP error correction, or “AT&F+MS=V32B” forcing B32bis (14,400 bps) connection. For International operation use “AT&F\N5;+GCI=xx;” forcing MNP error correction or “AT&F+MS=V32B;+GCI=xx;” forcing V32bis (14,400 bps) connection. Mobility Electronics, Inc...
- Page 12 Check your cables, cords, connections, and configuration setup before trying again. Modem/Serial switch is not set correctly. Check to be sure the Modem/Serial switch is set to Modem. Mobility Electronics, Inc...
- Page 13 If you require more information on the HotSync process, please refer to the HotSync chapter in your SPT Product Reference Guide. For help with other technical issues, contact Mobility Technical Support using the contact information provided at the start of this chapter. Mobility Electronics, Inc...
-
Page 14: Appendix A - Regulatory Information
• Consult the dealer or an experienced radio or television technician for help. Changes or modifications not expressly approved by Mobility Electronics could void the user’s authority to operate the product. Radio Frequency Interference Requirement - Canada This Class B digital apparatus complies with Canadian ICES-003. - Page 15 It does not imply that Industry Canada approved the equipment. The European Economic Area Mobility Electronics, hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from http://www.mobilityelectronics.com/hh_cradle_support/.
- Page 16 1999/5/CE. Spanish Por medio de la presente Mobility Electronics declara que el modem cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE Portuguese Mobility Electronics declara que este modem está...
-
Page 17: Appendix B - Warranty
Electronics, Inc. from a country other than the United States. Mobility Electronics, Inc. makes no other warranty of any kind with regard to this material. Mobility Electronics, Inc. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. - Page 18 Serial/Modem Charging Cradle User Guide Mobility California, Inc. 9918 Via Pasar, San Diego, CA 92126, USA Phone (858) 880-2225 • Fax (858) 530-2733 Email: invisioncradles@mobl.com • www.invisioncradles.com Part Number 190086-000 Rev A Mobility Electronics, Inc...
Need help?
Do you have a question about the Invision PS6S1800M and is the answer not in the manual?
Questions and answers