Table of Contents
Advertisement
Quick Links
INSTALLATION
AND SERVICE
MUST BE PERFORMED
BY A QUALIFIED
INSTALLER.
IMPORTANT:
SAVE FOR LOCAL
ELECTRICAL
INSPECTOR'S
USE.
READ AND SAVE THESE
INSTRUCTIONS
FOR FUTURE
REFERENCE.
If the information
in this manual is not followed
exactly,
a fire
or explosion
may result
causing
property
damage,
personal
injury or death.
FOR YOUR SAFETY:
m
Do not store or use gasoline or other flammable
vapors
and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL
GAS:
• Do not try to light any appliance.
• Do not touch any electrical
switch; do not use any phone
in your building.
• Immediately
call your gas supplier
from
a neighbor's
phone.
Follow the gas supplier's
instructions.
• If you cannot
reach your
gas supplier,
call the fire
department.
Installation
and service must be performed
by a qualified
installer,
service
agency or the gas supplier.
• ALL RANGES
CAN TIP
• INJURYTO
PERSONS
COULD
RESULT
• INSTALL
ANTI-TIP
DEVICE
PACKED
WITH
RANGE
• SEE INSTALLATION
INSTRUCTIONS
Note. For appfiances
installed
in the
State of Massachusetts
see page 2.
RANGE
OVERALL
253/4_'
DIMENSIONS
14--
30-1/8"
47-3/4"
Maximum
44 5/8"
Door Open
\\
29 7/8"
----
FRONT
SIDE
VIEW
VIEW
t
Minimum
to
1-13"4_1
. Cabinets
on
Maximum
Depth
18
Either
Side
for Cabinets
/7
of Range.
Above
Range Top.
30-118" _I
0" Clearance
Below
Cooking
Top and at Rear of Range.
Clearances
and Dimensions
1.
Location--Check
location where
the range will be installed. Check
for
proper
electrical
and gas
supply, and the stability of the
floor.
2.
Dimensions that are shown must
be used.
Given
dimensions
provide
minimum
clearance.
Contact
surface must be solid
and level.
Provide
Proper
Fuel Type
Before Proceeding:
Your range is preset to operate on natural gas only. This
model was shipped convertible
from the factory with the necessary
parts and
conversion
instructions
supplied.
DO NOT attempt to convert this range to LP/Propane
settings
without the proper LP/Propane conversion kit provided with the range or obtained
from your dealer.
Follow all instructions
provided with this conversion kit.
Espa_ol-
Paginas 9-16
P/N 316259328
EN_SP (0309)
1
Advertisement
Table of Contents
Related Manuals for Kenmore 79078822404
Summary of Contents for Kenmore 79078822404
- Page 1 INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage,...
- Page 2 Important Notes to the Installer Stepping, leaning or sitting on the doors Read all instructions contained in these installation or drawers of this range can result in serious injuries and instructions before installing range. can also cause damage to the range. Remove all packing material from the oven compartments •...
-
Page 3: Before Starting
Locate the Bracket Using the Template- (Bracket may Before Starting be located on either the left or right side of the range. Use Tools You Will Need the information below to locate the bracket if template is For leveling legs and Anti-Tip Bracket: not available). - Page 4 Level and Position Range- Level range by adjusting the (4) leveling legs with a wrench. Note: A minimum clearance of 1/8" is required between the bottom of the range and the leveling leg to allow room for the bracket. Use a spirit level to checkyour adjustments.
- Page 5 5. Read electrical connection details below Manual Flare Flexible Flare Union Pressure and connect electricity to range. Shutoff Union Appliance Adaptor Regulator Valve Conduit Before servicing, disconnect electrical supply at circuit breaker, fuse or power cord. Electric Requirements: A dedicated, properly grounded and polarized branch circuit protected by a 15 amp.
- Page 6 Operation of Surface Burners 7. Electric Ignition Surface Burners Operation of electric igniters should be checked after range Installation of Surface Burner Caps and supply line connectors have been carefully checked for Your range is equipped with any combination of the sealed leaks and range has been connected to electric power.
- Page 7 seconds after the thermostat is turned ON before the flame 8. Adjust the "LOW" Setting of Surface Burner appears at the oven burner. When the oven reaches the dial Valve (Linear Flow Valves Only): setting, the glowing igniter will go off. The burner flame will go "out"...
-
Page 8: Care, Cleaning And Maintenance
If theflameis yellowin color,increase air shutter opening Care, Cleaning and Maintenance size.(See "2" in illustration below.) If the flame is a distinct Refer to the Use & Care Guide for cleaning instructions. blue, reduce the air shutter opening size. To adjust loosen lock screw (see "3" illustration below), If removing range...