Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Comfort audio DS10
Summary of Contents for Comfort audio DS10
- Page 1 Comfort Digisystem User Manual SecureStream Technology Speaker DS10/DS20 English...
-
Page 2: Table Of Contents
User Manual Contents Page Introduction to Comfort Digisystem Introducing Speaker DS10/DS20 Functions – Speaker DS10/DS20 Connection options – Speaker DS10/DS20 First use Menu More functions Radio range and channels Accessories included Other original accessories Troubleshooting Service and warranty Technical data... -
Page 3: Introduction To Comfort Digisystem
Comfort Digisystem products. Speaker DS05 is also available as an accessory for Speaker DS20/DS-10. Speaker DS05 can be easily connected to the DS20 or DS10 using the cable supplied. Speaker DS20/DS10 is equipped with a range of inputs and outputs for connecting, for example, a wired microphone or loop amplifier. -
Page 4: Functions - Speaker Ds10/Ds20
Functions – Speaker DS10/DS20 Carrying handle Display Function indicators Function button WR1 and WR2 Menu control/OK Function button Pairing buttons WR1 and WR2* MIC – Volume Treble control control for wired microphone Bass control Mic in – for connection of e.g. -
Page 5: Connection Options - Speaker Ds10/Ds20
Connection options – Speaker DS10/DS20 The following connection options are on the back of Speaker DS10/ DS-20. Speaker DS20/DS10 has a wide range of connection options. MIC IN: A microphone with cable can be connected here. Volume strength from the microphone is adjusted using volume control MIC. -
Page 6: First Use
Start Speaker DS10/DS20 by pressing the On/Off button on the back of the active speaker. Receiver 1 and 2 (DS20 only) are started from the back of DS10/DS20, using the controls marked WR1 or WR2. Before adjusting the volume, the receivers in DS10/DS20, as well as the wireless microphones, must be set to the right channel and code key;... - Page 7 In these cases, the speaker should be positioned between the speaker and the audience, directed towards the audience in order to avoid feedback. Speaker DS10/DS20...
-
Page 8: Menu
To enter the main menu, press the Menu button. Below is a description of each menu. Use the function buttons to move the marker up or down. Press the Menu button to select. Channels WR1 Setting Receiver Channel 1 Speaker DS10/DS20... - Page 9 The option Send info sends information about both the code key and the channel from Speaker DS10/DS20 to Comfort Digisystem units that have been activated to receive info. Example: On Microphone DM-10 select Communication – Pairing – Receive info. Then carry out...
- Page 10 New code key makes it possible to generate a new code key and send info from Speaker DS10/DS20 to any Comfort Digisystem unit. Example: A Microphone DM-10 is used together with a Speaker DS20 and the system must be interception-proof. Hold the pairing button on DM-10 in for a few seconds to make the unit ready to receive pairing information.
- Page 11 When the box is ticked, the colour green indicates which channels have a low noise level and are suitable for use in the current environment. Check that no transmitters in the system are started when using FFC. Speaker DS10/DS20...
- Page 12 Speaker DS20; the system must be interception-proof. Hold the pairing button on DM-10 in for a few seconds to make the unit ready to receive pairing information. Then send the new code key from DS20 as in the menu picture above. Speaker DS10/DS20...
- Page 13 The squelch level can be adjusted from 0-10. The higher the squelch value, the stronger the radio signal required for the receiver to work. The receivers in Speaker DS10/DS20 are extremely sensitive and are thus able to receive weak signals. Raise the squelch value if the receiver is open to radio channels from other transmitters that must not be intercepted.
- Page 14 400 Hz. If this is deselected, a fuller bass sound is achieved. NB: the dial to adjust the treble and bass settings located on the rear of the speaker affects all outputs from the speaker including external audio inputs connected via “Mic in” and “Aux in” Speaker DS10/DS20...
- Page 15 On delivery the menu language is set to English. Factory reset Resets the unit to the factory settings. Also deletes all pairing information. About Here there is information about the product name and the software contained in the unit. Speaker DS10/DS20...
-
Page 16: More Functions
Disconnect the battery (mains operation without battery) If DS10/DS20 is permanently installed in a place where the On/ Off button is difficult to access, it is instead possible to turn DS10/ DS20 off by cutting the power to the power unit. - Page 17 3. Remove the battery. Pull it straight out. 4. Disconnect at least one of the flat pin sleeves. Make sure the flat pin sleeve cannot come into electrical contact with any of the battery terminals. Replace the cover. Speaker DS10/DS20...
-
Page 18: Radio Range And Channels
European countries: A 768 - 790 MHz B 854 - 863 MHz C 790 - 800 MHz D 800 - 820 MHz E 820 - 854 MHz F 865 - 872 MHz Speaker DS10/DS20... -
Page 19: Accessories Included
Accessories included Power unit Other original accessories Speaker DS05 Passive speaker for DS10/DS20, including 10 metre cable. Floor stands For mounting speakers on stands. Wall bracket For mounting speakers on walls. For a speaker and accessories. For floor stand. For other accessories, please visit our website www.comfortaudio.com... -
Page 20: Troubleshooting
Check that the transmitter and receiver are set to the same channel. Check the receiver settings. Loud hissing noise (no sound transfer) Check that the units are paired. Loud hissing noise (when no microphone is switched on) Increase squelch level. Speaker DS10/DS20... -
Page 21: Service And Warranty
Service and warranty Comfort Audio AB accords a limited warranty for two years as of the date of delivery. This covers all defects of manufacture and materials. For ac- cessories the warranty period is 90 days as of the date of delivery. Local agreements or regulations may exist. -
Page 22: Important Safety Instructions
12) Servicing may only be performed by a service provider approved by Comfort Audio AB. Servicing is required when the product has been damaged in any way, e.g. the plug or cord has broken, liquid has... - Page 23 19) Never charge the product in an enclosed non-ventilated space such as a bag, case or other enclosed storage area. 20) Only batteries and charging units from Comfort Audio AB may be used. WARNING! There is a risk of explosion if the battery is not changed correctly.
- Page 24 Manufactured by: Comfort Audio AB Box 154, SE-301 05 Halmstad, Sweden Tel. +46 35 260 16 00 Fax +46 35 260 16 50 info comfortaudio.com www.comfortaudio.com...
Need help?
Do you have a question about the DS10 and is the answer not in the manual?
Questions and answers