Making a Call Disconnecting a Call Remote Control Option Recording Option When Not in Use Specifications Warranty FCC Part 15 Compliance FCC Part 68 Compliance IC Compliance Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 4
Table 1. Remote ON/OFF Dip Switch Settings Table 2. Mic/Line Select Dip Switch Settings Table 3. Remote Connector Pinout Table 4. Line Connector Pinout Table 5. Set Connector Pinout Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
United States, Canada, the United Kingdom and mainland Europe, the SPH10 is optimal for your telephone application. This manual explains how to install, set up and operate the SPH10 in a step-by- step format. It also supplies instructions on how to resolve technical problems, should any arise.
At its midpoint, 12 o’clock, the trim pot is set for nominal caller level (0dBm). 5. Dip Switches. Four active dip switches (1, 3, 4, 12) configure the SPH10 system. Individual switch functions are defined in Operational Features (Page 6).
OFF state. Tip and ring from the phone line are not present at this point when the hybrid is in its ON state. Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
240Vac, 50/60Hz, no switching required. Telephone Line Requirements The SPH10 models operate on standard telephone lines and connect to the telephone system with a standard RJ11C modular jack. If you do not have an RJ11C jack where you want to install your SPH10, call your telephone company for installation.
Separate Mix Channel If the console has an extra mixing output channel, use this channel to mix all the audio you want to send to the SPH10 except the channel that will be connected to caller audio. Internal Mix Bus Mix-minus refers to a sum of all the audio sources in the console minus the caller audio.
If only microphone audio will be sent down the line, a separate microphone mixer (such as the Gentner MPAII Mixer/Power Amplifier) may be utilized. This audio can then be sent to the SPH10’s SEND input as well as the console input.
Verify all components and all connections. Ensure that proper power is supplied to the SPH10 and that the unit is OFF (the red OFF LED [7] will be lit; Figure 14, below). If the green ON LED [6] is lit, press the OFF button [9].
OFF button [3] to disconnect the call. Disconnecting a Call If the call is routed through the SPH10 (the ON LED [4] will be lit), press the OFF button [3]. The OFF LED [5] will light, and the ON LED [4] will extinguish.
Turn the recording device off when the call is finished. Figure 17. Two typical recording configurations When Not in Use The SPH10 is inactive when the red OFF LED [7] lit. POWER NOTE: Power should be maintained to the unit at all times. Technical or Setup Assistance...
0dBu line level output with a <50ohm impedance Unbalanced Audio In 0dBu line level >20kohm impedance On/Off Control Momentary closures to the switch common, unless latching-mode enabled Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
All specifications are subject to change without notice. Gentner Communications Corporation (Manufacturer) warrants that this product is free of defects in both materials and workmanship. Should any part of this equipment be defective, the Manufacturer agrees, at its option, to: A.
No user serviceable parts are contained in this product. If damage or malfunction occurs, contact Gentner Communications for instructions on its repair or return.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by Gentner Communications. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Page 18
Variation provided that an alternative form of warning was given. The expectation is that procedures complying with the General Variation should, generally, also meet the requirements of this condition. Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 19
To pin 6 of LINE RJ11C To pin 5 of LINE RJ11C To pin 2 of LINE RJ11C Ring To pin 1 of LINE RJ11C Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 20
Page 16 SPH10 Installation and Operations Manual Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 21
SPH10 Installation and Operations Manual Page 17 Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 22
Page 18 SPH10 Installation and Operations Manual Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 23
SPH10 Installation and Operations Manual Page 19 Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 24
Page 20 SPH10 Installation and Operations Manual Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 25
SPH10 Installation and Operations Manual Page 21 Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 26
Page 22 SPH10 Installation and Operations Manual Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 27
SPH10 Installation and Operations Manual Page 23 Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 28
Page 24 SPH10 Installation and Operations Manual Technical or Setup Assistance Telephone: 800.945.7730 (USA) or 801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com...
Page 29
“We are a technology innovation company with a highly specialized service.”...
Page 30
ENTNER OMMUNICATIONS ORPORATION Sales and Technical Assistance 1825 Research Way Salt Lake City, Utah 84119 Toll Free 800.945.7730 Telephone 801.975.7200 FAX 801.977.0087 FAX-On-Demand 800.695.8110 FAX-On-Demand International Line 801.974.3661 Worldwide Web Page @ http:\\www.gentner.com Gentner Part No. 800-012-201 (Rev. 1.1)