Advertisement
Quick Links
ENGL E765 Retro Tube Plug-in
Physically modeled tube guitar amp, speaker simulation and FX rack.
Owner's Manual
Standard Amp view
Developed under license by Brainworx for Plugin Alliance LLC, USA. Licensed to Universal Audio.
The ENGL E765 RT (Retro Tube) plug-in can be installed and operated like any other UAD-2 plug-in.
Please check
www.uaudio.com
for general info about the system requirements, etc.
Advertisement
Related Manuals for Engl E765 Retro Tube
Summary of Contents for Engl E765 Retro Tube
- Page 1 Owner’s Manual Standard Amp view Developed under license by Brainworx for Plugin Alliance LLC, USA. Licensed to Universal Audio. The ENGL E765 RT (Retro Tube) plug-in can be installed and operated like any other UAD-2 plug-in. Please check www.uaudio.com for general info about the system requirements, etc.
- Page 2 FX Rack / Zoom view Introduction The ENGL E765 RT plug-in is the next level in guitar processing. It offers a faithful digital rec- All of these features can be used or bypassed individually. You can - for example - bypass reation of the original tube amp circuit and adds several important tools to help guitarists in the Preamp of the plug-in and record your own original tube preamp using the plug-in’s...
- Page 3 A good producer’s trick is to use a REAL GUITAR AMP (a small combo, for example) for real-time monitoring in the control room during tracking while recording only the DI guitar signal! Then use the ENGL guitar amp plug-in when you play back the recorded tracks together with the rest of your music. You will need to split the dry guitar signal so it can be recorded in the computer and routed to the real guitar amplifier input at the same time.
- Page 4 (described later below) to store clean, crunch, rock and lead variations of the same or similar amp settings. This way you can turn the ENGL amp plug-in into a four-channel guitar amp easily and even automate the channel switches in your STANDBY and POWER DAW.
- Page 5 The controls of the ENGL FX Rack 1. NOISE GATE 2. AMP FILTERS (switchable pre / post) ‘CLOSED’ LED TIGHT Filter: When lit this LED indicates that the Noise Gate is CLOSED. This means the With the TIGHT filter you can cut LOW frequencies of either the DI guitar signal THRESHOLD setting is higher than the incoming guitar signal and the noise gate (PRE) or the processed amp output (POST).
- Page 6 CHAIN, playing a few notes again, grabbing the mouse again, etc. Using this impressive setup Dirk has produced a huge variety of customized ‘Re- cording Chains’ for the ENGL amplifiers, which you can apply to your plug-in amp set- Instead the ENGL amp plug-in offers you the AUTO mode: tings.
- Page 7 The controls of the ENGL FX Rack 4. LO-FI DELAY X2 & /2 (adjusting the delay time): We have modeled a vintage stomp box delay and modeled the typical sound of it. You may switch the actual delay time to double speed by clicking the /2 button.
-
Page 8: Input Gain
5. INPUT GAIN: 7. PRE-AMP and POWER AMP Activation: If you want to drive the input of the ENGL preamp harder or softer you may adjust the input gain to your liking. Some single coil pickups from older or vintage guitars BYPASS PRE: may deliver low level output which can be compensated with the INPUT GAIN. -
Page 9: Factory Presets
8. SETTINGS / Top Toolbar: FACTORY PRESETS We have made a lot of presets for the ENGL amp plug-in, many of them have been UNDO / REDO: made to work perfectly with classic guitars like Strats, Teles or Paulas. All of the...
Need help?
Do you have a question about the E765 Retro Tube and is the answer not in the manual?
Questions and answers