Table of Contents
Advertisement
Quick Links
For service questions, contact US Stove at 1-800-750-2723.
For sales inquiries, contact Sylvane at 1-800-934-9194 or visit www.sylvane.com.
TESTED &
LISTED BY
Report #: 215-S-22b-2
Please read this entire manual before installation and use of this appliance. Failure to follow
these instructions could result in property damage, bodily injury, or even death.
Contact your local building or fire officials about restrictions and installation inspection
requirements in your area.
SAVE THESE INSTRUCTIONS.
UNITED STATES STOVE COMPANY • 227 INDUSTRIAL PARK ROAD • SOUTH PITTSBURG, TENNESSEE 37380 • WWW.USSTOVE.COM
USSC
UNITED STATES STOVE COMPANY
"Keeping North America Warm Since 1869"
MULTI-FUEL FURNACE MODEL 8500
PORTLAND,
OREGON, USA
French version is available for download from the U. S. Stove website: http://www.Breckwell.com/
FOR TECHNICAL ASSISTANCE:
Owner's Manual
PHONE: (800) 750-2723
Approved for
US and Canadian use.
Safety tested and listed to UL
391-2010, ASTM E1509-04,
and CSA-B366.1-11
Certified for installation in a
residential or mobile home as a
stand-alone or add-on furnace
(ductwork connection only).
FAX: (423) 837-2109
1
Part No.: 851976
Advertisement
Table of Contents
Related Manuals for United States Stove Company 8500
Summary of Contents for United States Stove Company 8500
- Page 1 SAVE THESE INSTRUCTIONS. French version is available for download from the U. S. Stove website: http://www.Breckwell.com/ UNITED STATES STOVE COMPANY • 227 INDUSTRIAL PARK ROAD • SOUTH PITTSBURG, TENNESSEE 37380 • WWW.USSTOVE.COM FOR TECHNICAL ASSISTANCE: PHONE: (800) 750-2723 FAX: (423) 837-2109 USSC Part No.: 851976...
-
Page 2: Table Of Contents
Table of Contents Safety Precautions IMPORTANT: Read this entire manual before installing Disconnect the power cord before performing any TABLE OF CONTENTS ....................2 and operating this product. Failure to do so may maintenance! NOTE: Turning the ON/OFF Switch to SAFETy PrECAUTiONS ................... -
Page 3: Specifications
Specifications Fuel Considerations ShELLED COrN Heating Specifications (Dry, preferably corn with 11% or less moisture content) • Optimum moisture content of corn should be 11% or less. Wet corn will rapidly deteriorate furnace components, Input BTU/Hr 50,000 to 105,000 BTU/hr. reduce efficiency and void all warranties. -
Page 4: Installation
Installation Installation iNSTALLATiON OPTiONS read this entire manual before you install and use your Multi-Fuel Furnace. Failure to follow instructions CLEArANCES may result in property damage, bodily injury, or even death! (See specific installation details for clearances and other installation requirements) NOTE: Distance on the left-hand side of your Multi-Fuel Furnace is set at 24 inches for suitable access to the control panel and for fuel loading. -
Page 5: Venting Requirements
Installation Installation VENTiNG rEQUirEMENTS VENT TErMiNATiON CLEArANCES: Install vent at clearances specified by the vent manufacturer. Minimum 4-foot (1.22m) clearance below or beside any door or window that opens. Do not connect the pellet vent to a vent serving any other appliance or furnace. Minimum 1-foot (0.3m) clearance above any door or window that opens. -
Page 6: Through The Wall Installation
4-inches in diameter. between the air discharge of the 8500 furnace and the primary furnace. This duct damper prevents the air of the pri- Do not exceed more than 4-feet of pipe on a horizontal run and use as few elbows as possible. If an offset is required, mary furnace from back flowing to the secondary furnace. -
Page 7: Operation
Component Location Operation CONTrOL PANEL Turning the furnace OFF/ON, as well as adjustments for the fuel feed rate and room fan speed are performed by pressing the appropriate button(s) CLEANOUT TOOL on the control panel which is located on the lower left-hand side of your King furnace. -
Page 8: Start-Up Procedure
Operation LIGHTING INSTRUCTIONS DAiLy OPErATiON CAUTION: DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE The hopper and furnace top will be hot during operation; therefore, you should always use some type of HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT hand protection when refueling your furnace. -
Page 9: Interior Chambers
Maintenance Parts Diagram iNTEriOr ChAMBErS Open the Ash Cleanouts and scrap all ash into the ash pan. Open the damper and allow the ashes to fall into the ash pan. The damper may need to be slid in and out several times to clear any ash build-up. This may need to be done daily depending on fuel consumption. -
Page 10: Wiring Diagram
Parts List Wiring Diagram Amendment Part No. Part No. Description Description Qty. Qty. Part No. Part No. Description Description Qty. Qty. 23786 Door Latch (C000022) 891331 Spring Handle-Brushed Nickel 24179 Feed Door Handle 891364 Hearth Plate 25427 Retainer, Agitator Motor 891374 Access Panel, Plenum 40501... -
Page 11: Trouble Shooting
Trouble Shooting Error Codes Disconnect the power cord before performing any maintenance! NOTE: Turning the ON/OFF Switch to ”OFF” Below is a chart describing the Error Codes that might be displayed if an error occurs with your furnace. does not disconnect all power to the electrical components of the furnace. Error Error Possible... - Page 12 2. THE PART DESCRIPTION qOther _________________________ qDecoration qCost 3. THE MODEL NUMBER: 8500 What was the determining factor for purchasing your new appliance?_______ 4. THE SERIAL NUMBER:____________________ I have read the owner’s manual that accompanies this unit and fully understand the:...
- Page 13 For service questions, contact US Stove at 1-800-750-2723. For sales inquiries, contact Sylvane at 1-800-934-9194 or visit www.sylvane.com. Ê É Fold Here Fold Here Fold Here PLACE STAMP HERE United States Stove Company P.O. Box 151 South Pittsburg, TN 37380 USSC...
Need help?
Do you have a question about the 8500 and is the answer not in the manual?
Questions and answers