NAD C 275BEE Owner's Manual
  1. Manuals
  2. Brands
  3. NAD Manuals
  4. Amplifier
  5. C275BEE C/AH
  6. Owner's manual
NAD C 275BEE Owner's Manual

NAD C 275BEE Owner's Manual

Hide thumbs Also See for C 275BEE:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Owner's Manual
C 275BEE
®
Stereo Power Amplifier
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for NAD C 275BEE

Summary of Contents for NAD C 275BEE

  • Page 1 C 275BEE ® Stereo Power Amplifier Owner’s Manual...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 14 Outdoor Antenna Grounding - If an outside antenna or cable system SAVE THESE INSTRUCTIONS FOR LATER USE. is connected to the product, be sure the antenna or cable system is FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE grounded so as to provide some protection against voltage surges AUDIO EQUIPMENT.
  • Page 3 (including amplifiers) that produce heat. Changes or modifications to this equipment not expressly approved by NAD Electronics for compliance could void the user’s authority to operate WARNING this equipment. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS CAUTION REGARDING PLACEMENT PRODUCT TO RAIN OR MOISTURE.

  • Page 4: Notes On Environmental Protection

    120V 60HZ OR 230V 50HZ. RECORD YOUR MODEL NUMBER (NOW, WHILE YOU CAN SEE IT) The model and serial number of your new C 275BEE are located on the back of the cabinet. For your future convenience, we suggest that you record these numbers here: Model no: .

  • Page 5: Getting Started

    Insert the pin or bare cable end into 2 Connect your Preamplifier’ s PRE OUT to the C 275BEE rear panel’ s INPUT port. the hole and secure the cable by tightening down the terminal’s bushing.

  • Page 6: Identification Of Controls

    2 STANDBY LED: This indicator will light up amber when the C 275BEE PANEL. is in standby state. When the C 275BEE is at ON state, this indicator will illuminate blue. In cases of serious abuse of the C 275BEE, such as excessively low...

  • Page 7: Rear Panel

    REAR PANEL ATTENTION! Please make sure that the C 275BEE is powered OFF or unplugged before making any connections. It is also advisable to power-down or unplug all associated components while making or breaking any signal or AC power connections.

  • Page 8: Important Notes

    POWER switch when switching ON go to standby mode when the input signal source is turned OFF or goes or OFF the C 275BEE. If you intend not to use the C 275BEE for long below 20 mV.

  • Page 9: Power Drive

    REAR PANEL AUTOMATED TURN-ON LOGIC (ATO LOGIC) The C 275BEE may be turned ON in any one of three discrete ways for the same manner by which it was activated. In other words, if the C 275BEE complete system flexibility - from the front panel standby button, the is switched ON via a +12V-control signal, it cannot be switched to standby 12V-TRIGGER circuit or by the input signal-sensing circuit.

  • Page 10: Troubleshooting

    • Check connections to all speakers in the system. POWER/STANDBY LED stays red • There is short circuit in the speaker cabling. • Switch C 275BEE OFF and check speaker upon turning POWER ON. cable connections for both speaker terminals at the rear panel.

  • Page 11: Overall Specifications

    Shipping weight 16.9 kg * - Gross dimensions include feet, front panel button and extended speaker terminals. Specifications are subject to change without notice. For updated documentation and features, please log onto www.NADelectronics.com for the latest information about the C 275BEE.
  • Page 12 All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.

Table of Contents