Summary of Contents for ICP FIR-ULV600-DVR
- Page 1 FIR-ULV600-DVR User Manual Version 1.0 POS+DVR December 2005 FIR-ULV600-DVR User Manual Page: 1/56...
-
Page 2: Copyright Notice
Trademarks FIR-ULV600-DVR is registered trademarks of ICP Electronics Inc.; IBM PC is a registered trademark of International Business Machines Corporation. INTEL is a registered trademark of INTEL Corporation. AMI is registered trademarks of American Megatrends Inc. -
Page 3: Table Of Contents
Power Button (PS_ON1).................21 3.12 Power LED (LED1) ................22 3.13 Power SW/LED Connector (CN4)............22 3.14 Digital I/O with RJ-11 Connector (CN2)..........22 3.15 Power Connector (CN5 & CN8).............23 3.16 LCD Back Light Connector (CN6 & CN9) ..........23 FIR-ULV600-DVR User Manual Page: 3/56... - Page 4 South Bridge Chipset Configuration..........50 Setup submenu: Power................51 Setup submenu: Exit .................52 Appendix A Address Mapping................54 I/O Address Map ..................54 1st MB Memory Address Map..............54 IRQ Mapping Chart .................55 DMA Channel Assignment ..............55 Appendix B Digital I/O...................56 FIR-ULV600-DVR User Manual Page: 4/56...
-
Page 5: Chapter1 Introduction
Package: 421-pin BGA (31x31 mm) PCI Bus: Supports up to six master devices on PCI Other Feature: ◆ 6 USB 2.0 ports, 480MB/s ◆ IDE up to ATA 100 mode ◆ AC'97 2.3 CODEC support FIR-ULV600-DVR User Manual Page: 5/56... - Page 6 ◆ Enhanced Intel Speed Step technology support ◆ Optimized Clock Gating for 3D and Display Engines ◆ On-Die Thermal Sensor Wakeup on LAN: TBD Bootup Device IDE device: Yes Compact Flash: Yes USB device: Yes FIR-ULV600-DVR User Manual Page: 6/56...
-
Page 7: Package Contents
Before any installation, please check if the following materials are included in the package: One FIR-ULV600-DVR all-in-one single board computer One compact disk for utility and drivers If any of these items are missing or damaged, contact your distributor or sales representative immediately. -
Page 8: Chapter2 Installation
Chapter2 Installation This chapter gives instructions about how to set up the FIR-ULV600-DVR hardware, including directions of setting jumpers and connecting peripherals, switches and indicators. Before installation, please pay attention to the unpacking precautions on the following page for safety. -
Page 9: Board Layout
2.1.2 Board Layout Power Button LVDS1 LVDS2 VGA1 USB1 KB/MS JP10 VGA2 CN10 DDR DIMM Socket USB2 COM4 COM2 COM1 Power MIC SPK IDE1 JP11 COM5 LPT1 CN11 COM6 JP8 JP9 COM3+USB FIR-ULV600-DVR User Manual Page: 9/56... -
Page 10: Board Dimension
FIR-ULV600-DVR SBC. You can do it by using a grounded wrist strap at all times or by frequently touching any conducting materials that is connected to the ground. 2. Handle FIR-ULV600-DVR SBC by its edges. Don’t touch IC chips, leads or circuitry if not necessary. -
Page 11: System Memory Dram
*Note: All shaded rows in the tables of this manual are the default settings. TFT LCD Setting JP7/JP10: TFT LCD Voltage (5V / 3V) Setting JP7 for LVDS1, JP10 for LVDS2 JP7 & JP10 PIN STATE DESCRIPTION Short 1–2 3V TFT LCD Short 2–3 5V TFT LCD FIR-ULV600-DVR User Manual Page: 11/56... -
Page 12: Com4 Voltage Selection
+12V/+5V output Short 4-6 Ground output COM2 RI Function Setting JP5: COM2 RI Function Setting PIN STATE DESCRIPTION Short 1-2 RI is +5 Voltage output Short 3-4 RI function Short 5-6 RI is +12 Voltage output FIR-ULV600-DVR User Manual Page: 12/56... -
Page 13: Com1 Ri Function Setting
COM5 & 6 RI (CN11 pin8 & 18) Function Setting JP11: COM5 & 6 RI Function Setting JP11 PIN STATE DESCRIPTION Short 1-2 RI is +12 Voltage output Short 3-4 RI is +5 Voltage output FIR-ULV600-DVR User Manual Page: 13/56... -
Page 14: Chapter3 Connection
Digital I/O with RJ-11 connector Power SW/LED connector Power output connector CN6 & 9 LCD back light connectors Multi-function connector +12V DC power connector CN10 Internal Keyboard connector CN11 Serial port connectors Compact Flash Storage Card Socket (CF1) FIR-ULV600-DVR User Manual Page: 14/56... -
Page 15: Serial Port Connector (Com1, Com2, Com4, Com5 & Com6)
GROUND PULL DOWN CS1# CS3# GROUND IOR# IOW# IRQ15 MASTER/SLAVE RESET# IORDY DREQ DACK# ACTIVE# PDIAG# PULL DOWN GROUND Serial Port Connector (COM1, COM2, COM4, COM5 & COM6) COM1 & COM2: D-SUB Serial Port Connectors FIR-ULV600-DVR User Manual Page: 15/56... -
Page 16: Parallel Port Connector (Ltp1)
PIN NO. DESCRIPTION PIN NO. (DCD) (DSR) (RXD) (RTS) COM5 (TXD) (CTS) (DTR) +5V or +12V GROUND GROUND (DCD) (DSR) (RXD) (RTS) COM6 (TXD) (CTS) (DTR) +5V or +12V GROUND GROUND Parallel Port Connector (LTP1) FIR-ULV600-DVR User Manual Page: 16/56... -
Page 17: Primary Ide Connector (Ide1)
RESET# GROUND DATA 7 DATA 8 DATA 6 DATA 9 DATA 5 DATA 10 DATA 4 DATA 11 DATA 3 DATA 12 DATA 2 DATA 13 DATA 1 DATA 14 DATA 0 DATA 15 GROUND FIR-ULV600-DVR User Manual Page: 17/56... -
Page 18: Vga Connector (Vga1 & Vga2)
PIN NO. DESCRIPTION PIN NO. GREEN BLUE GROUND GROUND GROUND GROUND VCC / NC GROUND DDC DAT HSYNC VSYNC DDCCLK VGA2: 10-pin Box Header Connector VGA2 DESCRIPTION PIN NO. DESCRIPTION PIN NO. DDCCLK GREEN DDCDAT FIR-ULV600-DVR User Manual Page: 18/56... -
Page 19: Cpu & System Fan Connector (J4 & J5)
USB1 & USB2: 2 ports USB Connectors USB1 & USB2 PIN NO. DESCRIPTION PIN NO. DESCRIPTION USB Power USB Power DATA4- DATA5- DATA4+ DATA5+ GROUND GROUND LVDS Connector (LVDS1 & LVDS2) LVDS1 & LVDS2: LVDS Connectors FIR-ULV600-DVR User Manual Page: 19/56... -
Page 20: Box Header Connector (Cn7)
CH2 DATA0+ CH2 DATA0- GROUND GROUND LCD power LCD power LCD power LCD power Box Header Connector (CN7) CN7: COM3 & USB Box Header Connector DESCRIPTION PIN NO. DESCRIPTION PIN NO. USB0- USB1- USB1+ USB0+ FIR-ULV600-DVR User Manual Page: 20/56... -
Page 21: Keyboard/Mouse Connector (Kb_Ms1 & Cn10)
KEYBOARD CLOCK PC KB CLOCK KEYBOARD DATA PC KB DATA GROUND Note: Default short pin 2-3, 4-5 3.11 Power Button (PS_ON1) PS_ON1: Power Button PS_ON1 DESCRIPTION PIN NO. DESCRIPTION PIN NO. GROUND PS_ON GROUND GROUND FIR-ULV600-DVR User Manual Page: 21/56... -
Page 22: Power Led (Led1)
LED OFF + GROUND PS ON 3.14 Digital I/O with RJ-11 Connector (CN2) CN2: Digital I/O with RJ-11 Connector DESCRIPTION PIN NO. DESCRIPTION PIN NO. GROUND DGI/O OUT 0 DGI/O IN 0 +12V DGI/O OUT 1 GROUND FIR-ULV600-DVR User Manual Page: 22/56... -
Page 23: Power Connector (Cn5 & Cn8)
GROUND +12V GROUND 3.16 LCD Back Light Connector (CN6 & CN9) CN6 / CN9: LCD Back Light Connector CN6 for LVDS1, CN9 for LVDS2 CN6 & CN9 DESCRIPTION PIN NO. +12V +12V GROUND GROUND LCD_BKLEN FIR-ULV600-DVR User Manual Page: 23/56... -
Page 24: Audio Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION GROUND MIC In 3.17.3 Speaker Out Pin Header Connector (CN3) CN3: Speaker Out Pin Header Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION SPK Out (Left) GROUND SPK Out (Right) GROUND FIR-ULV600-DVR User Manual Page: 24/56... -
Page 25: Chapter4 Bios Setup
When changing the password or making other changes to the security setup BIOS Setup Options at Boot The user will be able to initiate SETUP by pressing the respective key. Press Delete to run Setup FIR-ULV600-DVR User Manual Page: 25/56... -
Page 26: Setup Submenu: Main
Select Screen ←→ Select Item ↑↓ System Memory Change Option Size : XXXXMB Select Field General Help Save and Exit System Time [XX:XX:XX] Exit Sy stem Date [Date MM/DD/YYYY] V02.57 ©Copyright 1985-2002, American Megatrends Inc. FIR-ULV600-DVR User Manual Page: 26/56... -
Page 27: Setup Submenu: Advanced
► SuperIO Configuration ► Hardware Health Configuration ► ACPI Configuration ► USB Configuration Select Screen ←→ Select Item ↑↓ Change Option Select Field General Help Save and Exit Exit V02.57 ©Copyright 1985-2002, American Megatrends, Inc. FIR-ULV600-DVR User Manual Page: 27/56... -
Page 28: Cpu Configuration
Change Option General Help Save and Exit ESC Exit V02.57 ©Copyright 1985-2002, American Megatrends, Inc. Options summary CPU TM function Disabled Enable Optimal Default, Failsafe Default This item en/disables TM (thermal management) function of CPU FIR-ULV600-DVR User Manual Page: 28/56... -
Page 29: Ide Configuration (Compatible Mode)
Save and Exit ESC Exit V02.57 ©Copyright 1985-2002, American Megatrends, Inc. Options summary Onboard PCI IDE Controller Disabled Primary Optimal Default, Failsafe Default Select how PCI IDE Controller works. Disabled: No device Primary: Enables primary IDE controller. FIR-ULV600-DVR User Manual Page: 29/56... -
Page 30: Primary Ide Master (If Attached Hard Disk)
Optimal Default, Failsafe Default CDROM ARMD Select the type corresponding to the device present. Not Installed: No device Auto: Auto detected CDROM: ATAPI CDROM ARMD: ATAPI Removable Media Device LBA/Large Mode Disabled Auto Optimal Default, Failsafe Default FIR-ULV600-DVR User Manual Page: 30/56... - Page 31 MWDMA n: Multiword DMA n UDMA n: Ultra DMA n Auto Optimal Default, Failsafe Default S.M.A.R.T. Disabled Enabled S.M.A.R.T. stands for “Self-Monitoring, Analysis and Reporting Technology”. 32Bit Data Transfer Disabled Failsafe Default Enabled Optimal Default FIR-ULV600-DVR User Manual Page: 31/56...
-
Page 32: Super Io Configuration
Optimal Default, Failsafe Default 3E8/IRQ4 2E8/IRQ3 This item selects Serial Port1 Base Addresses. Serial Port2 Address (/IRQ) Disabled 2F8/IRQ3 Optimal Default, Failsafe Default 3E8/IRQ4 2E8/IRQ3 This item selects Serial Port2 Base Addresses. Normal Optimal Default, Failsafe Default IrDA FIR-ULV600-DVR User Manual Page: 32/56... - Page 33 Serial Port3 Address Disabled Optimal Default, Failsafe Default This item selects Serial Port3 Base Addresses. Serial Port3 IRQ Optimal Default, Failsafe Default This item selects IRQ for Serial Port3. Serial Port4 Address Disabled Optimal Default, Failsafe Default FIR-ULV600-DVR User Manual Page: 33/56...
- Page 34 This item selects IRQ for Serial Port5. Serial Port6 Address Disabled Optimal Default, Failsafe Default This item selects Serial Port6 Base Addresses. Serial Port6 IRQ Optimal Default, Failsafe Default This item selects IRQ for Serial Port6. FIR-ULV600-DVR User Manual Page: 34/56...
-
Page 35: Hardware Health Configuration (Manual Mode)
Save and Exit +5.00V : X.XX V +2.50V : X.XX V Exit SYSFAN Mode Settig [Manual Mode SYSFAN Control [value] CPUFAN0 Mode Settig [Manuak Mode CPUF AN0 Control [value] V02.57 ©Copyright 1985-2002, American Megatrends, Inc. FIR-ULV600-DVR User Manual Page: 35/56... -
Page 36: Hardware Health Configuration (Thermal Cruise Mode)
SYSFAN TartgetSpeed Value [value] Select Item SYSFAN Tolerance Value [value] ↑↓ Change Option CPUFAN0 Mode Settig [Manuak Mode General Help CPUF AN0 Control [value] Save and Exit E SC Exit V02.57 ©Copyright 1985-2002, American Megatrends, Inc. FIR-ULV600-DVR User Manual Page: 36/56... - Page 37 This item determines FAN stop time value. Max =255 Speed Cruise Mode SYSFAN TargetTemp value Optimal Default, Failsafe Default This item determines target FAN speed. Max =255 SYSFAN Tolerance value Optimal Default, Failsafe Default This item determines tolerance of target speed. Max =15 FIR-ULV600-DVR User Manual Page: 37/56...
-
Page 38: Acpi Configuration
Change Option General Help Load Defaults Save and Exit Exit V02.57 ©Copyright 1985-2002, American Megatrends, Inc. Options summary ACPI Aware O/S Optimal Default, Failsafe Default This item En/Disables ACPI to fit supportability of Operation System. FIR-ULV600-DVR User Manual Page: 38/56... -
Page 39: Usb Configuration
Optimal Default, Failsafe Default This item configures the mode of USB 2.0 controller. It won’t appear if USB2.0 controller is disabled. BIOS EHCI Hand-Off Disable Enable Optimal Default, Failsafe Default This item en/disables BIOS EHCI hand-off. FIR-ULV600-DVR User Manual Page: 39/56... -
Page 40: Setup Submenu: Boot
► Boot Device Priority ► Hard Disk Drives ► Removable Devices Select Screen ←→ ► CD/DVD Drives Select Item ↑↓ Change Option General Help Load Defaults Save and Exit Exit V02.57 ©Copyright 1985-2002, American Megatrends, Inc. FIR-ULV600-DVR User Manual Page: 40/56... -
Page 41: Boot Settings Configuration
This item determines the appearance of the system at start-up time. If the value is set to “Disabled,” the results of the POST (Power On Self Test) are displayed. If the value is set to “Enabled,” a Logo screen is displayed. FIR-ULV600-DVR User Manual Page: 41/56... - Page 42 This item en/disables the message. Hit ‘DEL’ Message Display Disable Enable Optimal Default, Failsafe Default This item en/disables the message. Disable Interrupt 19 Capture Enable Optimal Default, Failsafe Default This item allows option ROMs to trap int 19. FIR-ULV600-DVR User Manual Page: 42/56...
-
Page 43: Boot Device Priority
↑ or ↓ to select, then press ENTER to change it. ←→ Select Screen ↑↓ Select Item Change Option General Help Load Defaults Save and Exit ESC Exit V02.57 ©Copyright 1985-2002, American Megatrends, Inc. FIR-ULV600-DVR User Manual Page: 43/56... -
Page 44: Hard Disk Drives
Removable Devices Specifies the boot ____________________________________________________ sequence from the Drive Floppy Drive] available devices. ←→ Select Screen Select Item ↑↓ Change Option General Help Load Defaults Save and Exit Exit V02.57 ©Copyright 1985-2002, American Megatrends, Inc. FIR-ULV600-DVR User Manual Page: 44/56... -
Page 45: Cd / Dvd Drives
Specifies the boot ____________________________________________________ sequence from the Drive [LG CD-ROM CRD-8484] available devices. Select Screen ←→ Select Item ↑↓ Change Option General Help Load Defaults Save and Exit Exit V02.57 ©Copyright 1985-2002, American Megatrends, Inc. FIR-ULV600-DVR User Manual Page: 45/56... -
Page 46: Setup Submenu: Security
Setup utility. Removing the Password Highlight this item and type in the current password. At the next dialog box press Enter to disable password protection. FIR-ULV600-DVR User Manual Page: 46/56... -
Page 47: Setup Submenu: Chipset
► North Bridge Configuration ► South Bridge Configuration Select Screen ←→ Select Item ↑↓ Enter Change General Help Load Defaults Save and Exit Exit V02.57 ©Copyright 1985-2002, American Megatrends, Inc. FIR-ULV600-DVR User Manual Page: 47/56... -
Page 48: North Bridge Chipset Configuration
This item allows user to choose initiating priority of graphic adapters. Internal Graphic Mode Select Disable Enabled, 1MB~16MB Enabled, 32MB Optimal Default, Failsafe Default This item selects the amount of system memory used by Internal graphic device. FIR-ULV600-DVR User Manual Page: 48/56... - Page 49 This item selects which device to display when booting. Flat Panel Type 640x480LVDS 800x600LVDS 1024x768LVDS 24bits 1280x10240LVDS 1400x1050LVDS 1024x768LVDS 18bits Optimal Default, Failsafe Default 1600x1200LVDS 1280x1024 48bits 800x600 24bits 800x600 18bits 1024x768 36bits 640x480LVDS This item selects current LFP type. FIR-ULV600-DVR User Manual Page: 49/56...
-
Page 50: South Bridge Chipset Configuration
Optimal Default, Failsafe Default This item en/disables onboard LAN. Onboard AC’97 Audio Disable Auto Optimal Default, Failsafe Default This item en/disables onboard AC’97 Audio. Spread Spectrum Mode Disable Optimal Default, Failsafe Default Enable This item en/disables spread spectrum. FIR-ULV600-DVR User Manual Page: 50/56... -
Page 51: Setup Submenu: Power
Optimal Default, Failsafe Default This item selects which state to go when the power restores after AC power loss. Resume On Ring Disable Optimal Default, Failsafe Default Enabled This item en/disables resume on ring event. FIR-ULV600-DVR User Manual Page: 51/56... -
Page 52: Setup Submenu: Exit
Setup utility and exit the Setup utility. When the Exit Discarding Changes dialog box appears, press [OK] to discard changes and exit, or press [Cancel] to return to the setup main menu. [ESC] key can be used for this operation. FIR-ULV600-DVR User Manual Page: 52/56... - Page 53 Setup utility. Select the [OK] item to indicate yes, and then press Enter to bypass the optimal settings changes Load Failsafe Defaults Load Failsafe Default values for all the setup questions. [F8] key can be used for this operation. FIR-ULV600-DVR User Manual Page: 53/56...
-
Page 54: Appendix A Address Mapping
AGP Graphic Adapter 3E8-3EF Serial Port 3 3F0-3F7 Floppy Disk Controller 3F8-3FF Serial Port 1 Watchdog timer enable 480-48F PCI BUS 1st MB Memory Address Map Memory address Description 00000-9FFFF SYSTEM MEMORY A0000-BFFFF VGA BUFFER FIR-ULV600-DVR User Manual Page: 54/56... -
Page 55: Irq Mapping Chart
IRQ12 PS/2 mouse IRQ5 USB IRQ13 FPU IRQ6 Floppy Disk IRQ14 Primary IDE Controller IRQ7 Printer IRQ15 Secondary IDE DMA Channel Assignment Channel Function Available Available Floppy disk Available Cascade for DMA controller 1 Available Available Available FIR-ULV600-DVR User Manual Page: 55/56... -
Page 56: Appendix B Digital I/O
Output pin1: bit 1 Example: out 280, 0 set output pin 0,1 to low out 280,03 set output pin 0,1 to high Input port address: 281H Input pin0: bit 0 Example: in 281 read input pin 0 Temperature FIR-ULV600-DVR User Manual Page: 56/56...