Advertisement
Advertisement
Table of Contents
Related Manuals for PurePower 700
Summary of Contents for PurePower 700
- Page 1 PurePower User’s Guide and Warranty Information PurePower 100/110/120 Volt models...
-
Page 2: Table Of Contents
Contents Table of Contents About the PurePower APS Safety Warnings Installation Inspecting the Equipment PurePower Preparation Activating Up Your PurePower Operation PurePower Maintenance Specifications Troubleshooting Service and Support | 01 Audio/Video Power Supply • www.purepoweraps.com... -
Page 3: About The Purepower Aps
• The APS improves amplifier performance by ensuring full wattage and improves signal component output quality by removing noise and distortion. • The PurePower APS design allows any of our high quality, full contact receptacles to supply digital, analog or amplifier components. -
Page 4: Safety Warnings
Safety Warnings Safety Warnings Read the following precautions before you install the APS. IMPORTANT SAFTEY INSTRUCTIONS - SAVE THESE INSTRUCTIONS. This manual contains important instructions that you should follow during installation and main- tenance of the APS and batteries. Please read all instructions before operating the equipment and save this manual for future reference. -
Page 5: Installation
The PurePower package includes: PurePower APS Quick Start Guide Input line cord with an IEC female connector to fit the PurePower input connector and a Nema 5-15P (700 and 1050) or Nema 6-20P (2000) plug. Rack mount bracket kit This manual... -
Page 6: Purepower Preparation
Rack-Mount The APS can be installed in 19 or 23-inch racks and needs only 2U of rack space for 700 adn 1050 models, 3U for the 2000. Mounting rails or a rack shelf are recommended. - Page 7 AV system that is otherwise isolated from surges arising in the AC power lines by the PurePower APS. It is intended to prevent a back door attack that would circumvent the PurePower protection.
- Page 8 If your PurePower 1050 is not equipped with a Power Pack connector and you wish to add one or more Power Packs, the unit can be factory retrofit. Please contact PurePower service for details.
-
Page 9: Activating Up Your Purepower
The APS will operate in Bypass mode for a few seconds, then turn on its inverter out- put - indicated by the LCD Display. The PurePower APS is now in Normal mode and ready to sup- ply power to your system. Turn on the components, ensuring that the total load does not exceed the capacity of the PurePower APS. - Page 10 "Output" LED illuminates. The LCD display will indicate "bypass" for a few seconds and then indicate "Line Normal" mode and display the output voltage. Starting the PurePower APS on battery To turn on the APS when utility power is unavailable, press and hold the On/Off button until the blue "Output"...
-
Page 11: Operation
Operation Operation The PurePower unit indicates the APS status through the LCD Display. Pressing the "Display" button on the control panel will cycle through the 5 information displays. The display presents data on 2 lines. The top line indicates the current operating mode:... -
Page 12: Bypass Mode
Operation Bypass Mode In the event of an extended APS overload or internal failure, the APS transfers your system to util- ity power. Battery mode will not be available, however the utility power continues to be passively filtered by the APS. The LCD display will indicate "Bypass" when bypass mode is engaged. The APS switches to Bypass mode when: ·... -
Page 13: Test Mode
APS or a possible internal problem. Unplug each load in turn. If the problem continues after all loads have been removed the message may indicate a problem with the APS itself. Please notify PurePower Service for further instructions. Over Load When the APS detects an overload condition its behavior varies with the amount and duration of the overload. -
Page 14: Purepower Maintenance
"Line Normal" mode . The unit will switch to battery mode for 10 seconds to test the batteries. If the test indicates a battery fault, contact PurePower or your PurePower dealer to order new batteries. The average battery life is aproximately 5-7 years. -
Page 15: Specifications
Specifications Specifications This section provides the following specifications for the PurePower APS · Electrical input and output · Weights and dimensions · Environmental and safety · Battery Model List Model List VA/Watts VA/Watts VA/Watts Weight Lb (Kg) Weight Lb (Kg) - Page 16 Specifications Environmental and Safety Environmental and Safety Operating Temperature Operating Temperature Operating Temperature 0°C to 32°C (32°F to 90°F) 0°C to 32°C (32°F to 90°F) 0°C to 32°C (32°F to 90°F) Optimal battery performance: Optimal battery performance: 21°C (72°F) 21°C (72°F) Storage Temperature Storage Temperature 0°C to 25°C (32°F to 77°F)
-
Page 17: Troubleshooting
Troubleshooting Troubleshooting your PurePower APS This section contains troubleshooting information and an explanation of APS alarm conditions. Condition Condition Possible Cause Possible Cause Resolution Resolution The LED indicator lights Power cord not connected Check connections are not on or APS won’t start... -
Page 18: Service And Support
For setup and support for your PurePower APS, please contact your authorized PurePower Dealer. For warranty service, please contact your authorized dealer or PurePower. All PurePower APS models have a two year warranty for original registered owners. If we are unable to solve a prob- lem with your APS over the phone, we’ll provide fast repair or replacement. - Page 19 Pure Power in > Pure Sound out • www.PurePowerAPS.com...
Need help?
Do you have a question about the 700 and is the answer not in the manual?
Questions and answers