Advertisement
Quick Links
METERING
SPREAD LAVATORY
FAUCETS
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
TOOLS REQUIRED
Tubing Cutter
SPOUT ASSEMBLY
Install RING WASHER (1) into SPOUT (2) recess. Check
that O-RING (3) on end of SPOUT SHANK (4) is in place. Insert
SPOUT SHANK (4) into center hole on mounting surface.
Assemble RUBBER WASHER (5) and BRASS WASHER (6) and
LOCKNUT (7) onto SPOUT SHANK (4). Align SPOUT ASSEMBLY.
From underside of ledge, tighten LOCKNUT (7) to secure SPOUT
ASSEMBLY to mounting surface.
SPOUT RECESS
4
5
6
7
Installation
Instructions
1340.725
1340.825
1340.855
1340.865
Channel Locks
Turn off hot and cold water
CAUTION
supplies before beginning.
SPOUT
ASSEMBLY
2
1
3
MOUNTING
SURFACE
1340.725
1340.825
Adjustable Wrench
Plumbers' Putty or Caulking
PREPARE TUBE AND TEE ASSEMBLY
Remove COUPLING NUT (1) and FERRULE (2) from each
VALVE (3) and slide onto TUBING (4).
!
REMOVE HANDLE AND
ACTUATOR ASSEMBLY
Remove HANDLE (1) by
removing INDEX BUTTON (2)
and SET SCREW (3) with a
2.5mm hex wrench.
Pull off HANDLE (1).
Remove ACTUATOR
ASSEMBLY (4).
Remove WASHER (5).
NOTE; Washer (5) may remain
inside of Actuator Assembly.
1340.855
Certified to comply with ANSI A112.18.1M
2.5mm Hex Wrench
1
2
8"
MOUNTING
SURFACE
3
2
REMOVE
1340.865
968492
4
1
2
3
1
REPLACE
4
5
Advertisement
Related Manuals for American Standard 1340
Summary of Contents for American Standard 1340
- Page 1 Assemble RUBBER WASHER (5) and BRASS WASHER (6) and LOCKNUT (7) onto SPOUT SHANK (4). Align SPOUT ASSEMBLY. From underside of ledge, tighten LOCKNUT (7) to secure SPOUT ASSEMBLY to mounting surface. SPOUT RECESS Installation Instructions 1340.725 1340.825 1340.855 1340.865 1340.725 1340.825 Adjustable Wrench...
- Page 2 5/16'' MIN. VALVE ASSEMBLY (1340.725) For Cold or Tempered Water Supply Valve assembly is same as two handle lavatory faucets. See above instructions for assembly, (1340.725 Single Valve Faucet) is for Cold or Tempered water only. 5/16'' MIN. MOUNTING SURFACE...
- Page 3 INSTALL HANDLES Remove INDEX BUTTON (1; 2) and loosen SET SCREW (3) with a 2.5mm hex wrench. Install HANDLES (4) onto VALVE STEM (5). Tighten SET SCREWS (3) with 2.5mm Hex Wrench. Replace INDEX BUTTONS. Red (1) in Left HANDLE (4) Blue (2) in Right HANDLE (4).
- Page 4 ASSEMBLY 033757-0070A TEE MTG. KIT 6" SPOUT KIT M962394-YYY0A M962405-YYY0A METERING Center Set Faucets PRODUCT NUMBERS 1340.825 1340.725 5" GN 1340.855 6" GN 1340.865 M962399-YYY0A SPOUT KIT M962393-YYY0A 1.56 GPM AERATOR M962400-0070A TUBE & TEE ASSEMBLY (FOR 1340.725) M962394-YYY0A AERATOR 5"...