Download Print this page

Perfect Water Technologies Home Master HMF1C Installation & Service Manual page 3

Advertisement

Home Master
®
Water Filter Owners Manual
Filter Change Instructions
1. For well water—shock chlorinate your well and pipes prior to removing filters.
2. Turn off the water supply to the system. Depress the red pressure release button on the top of
the filter housing cap to relieve system pressure. If your system was not equipped with a
pressure relief valve, leave open a nearby faucet. This will make removing the filter housing
possible.
3. Unscrew the housing (sump) from the cap using the filter wrench included with your system, or
a commercially available "strap" type wrench. Remove and discard old filter cartridge.
4. Scrub the sump and cap with warm water mixed with about 2 tablespoons of household bleach
using a sponge or soft rag. Wear rubber gloves.
5. A) Pour 2 cups of unscented concentrated bleach in each empty sump and close the system to
hand tight and fit snug tight with the wrench. DO NOT over tighten. B) Drain your hot water
heater. C) Open the main water supply to the system. D) Open a faucet at the furthest point
from the system and run water until you smell the chlorine. Flush the toilet. Repeat at each point
of use moving towards the filter system. E) Close the main water supply to the system. F) Open
each housing.
6. Lubricate the o-ring with clean silicon grease if needed. DO NOT USE PETROLIUM JELLY.
Insert o-ring in grove and press into place taping the o-ring all the way around. Make sure the o-
ring is seated level. Replace o-ring if damaged or stretched.
7. Remove filter packaging and insert new filter cartridge into the sump, making sure that it slips
over the standpipe in the bottom of the sump.
8. Fit the bottom of the housing (sump) into the cap and hand tighten, then use the filter wrench to
fit snug. Do not over tighten.
9.
Turn on the water supply slowly to allow the system to fill with water. Close any open valves
downstream of the system once water flows and air is purged. Inspect system carefully for
leaks. If a leak is found, first follow the shut off de-pressurization procedure and then remove
the housing to inspect the o-ring to ensure that it is seated properly. Then retighten.
10.
Flush the system by turning on a few cold-water faucets. Allow the water to run until the air and
carbon has been purged. Water may be cloudy initially. New activated carbon filter cartridges
may contain loose carbon and air bubbles after installation.
Page 6
Customer Service Hotline 1-877-693-PURE
Installing The Whole House Filtration System
Tools Required
Safety glasses
Towels
Flat head screwdriver
Medium Crescent wrench
Monkey wrench
Parts required (not included)
(2) shut off valves
(2) hex nipples or pipe nipples
(2) pipe unions
(1) ground jumper cable
(2) pipe hangers
USE A LICENECED PLUMBER TO INSTAL THIS PRODUCT
Preliminary Notes
This installation guide provides a step by step, start to finish procedure
for installing your Home Master® water filter.
All steps provided herein are for typical installations only. You application
may be different.
Pre-Installation
For well water - SHOCK CHLORINATE your well and pipes immediately
prior to installation and every filter change.
Filter should be protected from freezing, direct sunlight, extreme
temperatures, kept dry and level.
Make a list of all the plumbing fittings and tools you will need to
completely install the system according to your application.
Turn the water off to your house while installing the system.
Turn off the electricity to your electric water heater during installation.
After the system is installed and pressurized, turn on a few hot and cold-
water faucets, and let them run until there is no more air in your lines,
then turn the electricity back on to your water heater.
Use Teflon tape on threaded fittings.
Be sure to note inlet and outlet markings. The sediment filter is the first
stage of the water filter.
Customer Service Hotline 1-877-693-PURE
Home Master
®
Water Filter Owners Manual
hacksaw
Soldering iron or torch
Power drill
Teflon tape
bypass valve (s) (optional)
pressure gauge (s) (optional)
pressure regulator (as needed)
Page 3

Advertisement

loading

This manual is also suitable for:

Home master hmf2sdgcHome master hmf2sdgcckdf85Home master hmf3sdgfecHome master hmf3sdgncckdf85Hmf-cyoHome master hmf-cyo