GLOVIEW 3D TOUCH INTERACTIVE WHITEBOARD MANUAL Introduction Gloview 3D Touch Interactive Whiteboard is attached with Projector/LCD and turns any flat surfaces into interactive and collaborative workspace. It is an inexpensive Interactive Solution. Key Features 1, Remote Writing with Laser Pen;...
Page 4
GLOVIEW 3D TOUCH INTERACTIVE WHITEBOARD MANUAL Package Includes Calibration Device 8m USB Cable Hardkey Infrared Pen (short style) Laser Pen Extra Power Ceiling Mount Battery size for infrared pen: 2 pieces, AAA (non included) Battery size for laser pen: 1 pieces, CR2032, 3V (non included)
Install the Calibration Device to the ceiling with the mount and the distance to the front of the projection screen / surface (based on 80’’ Projection Screen) should be approximately 2.5- 3m (for Long Throw Model LP1O) or 1.2m (for Short Throw Model SP1O).
Calibration Software Calibration Step 1: Place the small software CD-ROM into the CD drive and copy the “Gloview Calibration Software’’ and “Gloview Application software’’ folder in the CD-ROM onto your PC’s hard disk drive. Please Note: do not RUN the software from the CD.
Page 7
GLOVIEW 3D TOUCH INTERACTIVE WHITEBOARD MANUAL Next, please connect USB with computer again and keep adjusting the location or angel of calibration device or move any strong light until there is no green dot or box in the viewing window. Please note: If there is any green box in this red screen, calibration will not work.
Page 8
GLOVIEW 3D TOUCH INTERACTIVE WHITEBOARD MANUAL Step 4: Make sure the whole projection image/LCD image should be able to be involved in the viewing window (see Picture 7) Picture 7 Step 5: Manual Calibration Open “Operation”—Choose “Manual Calibration”, and complete the total 9/36 calibration points to finish...
Page 9
GLOVIEW 3D TOUCH INTERACTIVE WHITEBOARD MANUAL Picture 10 Picture 11 Automatic Calibration “Operation”—Choose “Automatic Calibration” and it will automatic complete the calibration within 4 seconds (see Picture 12) Picture 12...
Page 10
GLOVIEW 3D TOUCH INTERACTIVE WHITEBOARD MANUAL Step 6: After Automatic Calibration finished, Viewing Window will be Minimized in the right corner of the computer. Step 7: To make the device run with system start. Please right click the Icon . And select “Auto Run At System Startup”...
Step 3: Open the folder “Gloview IWB Application Software’’ and run , There will be a icon of tBoard on the desktop. Now the Application software of “tBoard” is installed. Step 4: Open the “Gloview IWB Application software’’ and install “Handwriting Recognition’’.
GLOVIEW 3D TOUCH INTERACTIVE WHITEBOARD MANUAL tBoard Software Manual Double click the icon of tBoard from the desktop. Start Menu Introduction Click the menu , then the tool list will pop up, click the option according to the different needs.
Page 13
GLOVIEW 3D TOUCH INTERACTIVE WHITEBOARD MANUAL Start Previous Insert Text Zoom Undo、 Select Desktop Menu Tools Page & Next Shape Option In/Out Width Redo New File Hard Pen、 Insert Fill Move Pen and Eraser Expansion Brush Pen Image Tools Screen...
Page 14
GLOVIEW 3D TOUCH INTERACTIVE WHITEBOARD MANUAL Step 2: Using the Handwriting Recognition in Word file, Excel file and tBoard. In Word and Excel file Open the Word and Excel file from computer procedure and you will use it as like the Picture 1 and 2.
Page 15
Step 1: Open the “Handwriting Recognition’’, then click the virtual keyboard in the toolbar. Step 2: The soft keyboard could be used in the Word file, Excel file and IE, etc Multi-writing Trial Version Before making multi writing demo, please Find the folder “Gloview Calibration Software’’ and run...
GLOVIEW 3D TOUCH INTERACTIVE WHITEBOARD MANUAL Tips 1, The range of light Sensitivity should be 5-8. If too high, the mouse will be out of control. If too low, the pen may not response well with operation. 2, The distance between Calibration Device to the screen (based on 80’’ screen): Around 2.5-3m (for Model LP1O)