Page 6
17.1 Connecting the VMS4.1™ to your PC .................................. 44 Setup ............................................ 46 Cleaning ..........................................47 Crossfader Replacement ...................................... 48 20.1 Replacing How-To ....................................... 48 ROHS – A Contribution to the Conservation of Environment ..........................49 WEEE – Waste of Electrical and Electronic Equipment ............................50 Specifications ........................................
5. U NPACKING Every VMS4.1™ has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your system for any damage and be sure all equipment necessary to operate the system has arrived intact.
UPPORT American Audio® provides a toll free customer support line to provide set up help and to answer any questions, should you encounter problems during your initial set-up or operation. You may also visit us on the web at www.AmericanAudio.us for any comments or suggestions.
10. S 10.1 C HECKING THE ONTENTS Be sure your VMS4.1™ was shipped with the following: VMS4.1™ Controller Operating Instructions (This Booklet) USB Cable 5V Power Adapter Virtual DJ Software Warranty Card 10.2 I NSTALLING THE NITS Place your unit on a flat surface or mount it in a secure rack mount case.
Page 21
ONNECTIONS Use a 1/8” mono (not stereo) mini plug cable to connect your VMS4.1™ to a mini jack connection (A or B) on a compatible American Audio® or American DJ® “Fader Q Start” mixer. (This will enable the Fader “Q” Start function - see chapter 12.3.1 Outputs (33-38) on page 32).
Page 27
When no Cue sources are selected, these indicate the volume level on the Master Output. When one or more Cue sources are selected, these indicate the volume level on all of the Cue sources combined. At power-on, these indicate the VMS4.1™ firmware version. If the left side lights up 1 LED and the right side lights up 3 LEDs, the firmware version is 1.3.
Page 28
(14) Jog Wheel – This wheel has three functions: Attention: Make sure that NOTHING is touching or resting on the jog wheels when you power on the VMS4.1™. The wheel works as a pitch bend during playback. Turning the wheel clockwise can increase the pitch percentage up to 100%, and turning the wheel in the counter-clockwise direction can decrease the pitch percentage down to -100%.
IXER ONTROLS The VMS4.1™ can be used as a MIDI control, a stand-alone mixer, or combination giving you maximum control of your music collection whether it be on vinyl, digital CDs or Computer DJ software (Virtual DJ LE included). (24) USB/Analog Switch – These will switch the corresponding channel from USB audio stream or analog audio input. USB will route the software assigned ASIO audio channel thru the corresponding MIDILOG channel.
Page 31
(26-28) NTERFACE The VMS4.1™ can be used as a MIDI control, a stand-alone mixer, or combination giving you maximum control of your music collection whether it be on vinyl, digital CD's or Computer DJ software (Virtual DJ LE included). (26) 4 OUT: 4 OUT X 4 IN USB – Sets MIDILOG channels 2 & 3 to receive audio from software with ASIO outputs and sends audio or control tones from the channel 2 &...
(31) Headphones Jack – Connect your headphones to this jack. The headphone signal is controlled by the controls described previously. 12.3 R ANEL (32) Power Switch – This switch will turn the VMS4.1™ on/off. Attention: Make sure that NOTHING is touch or resting on the jog wheels when you power on the VMS4.1™. 12.3.1 O...
Page 33
RCA outs at the same time; this may affect your output. To set your desired volume, use the Master Volume Knob. (37) Booth Outputs – The VMS4.1™ offers a secondary output usually used to monitor your mix or to route to an outboard recording device. This output has independent volume control Booth knob.
13.1 - 4 O The VMS4.1™ can act like a 4x4 audio interface. Your USB audio is routed through the VMS4.1™'s MIDILOG Ch. #2 and #3 inputs. If you wish to route the inputs via USB for software play-through or Timecode Control, set your desired VMS4.1™ Channel to the USB setting and the channels' Line/Phono Selector Switch (41) to the correct setting.
Normal Mode has a MIDI Latency of 10 milliseconds, this is the default mode. Turbo Mode has a MIDI latency of 1 millisecond. To set the VMS4.1™ to Turbo Mode, proceed as follows: Before powering on, press and hold the CUE, Play, and Pause buttons on the left side.
EQ M In Pre EQ Mode, the USB audio signal is affected by the VMS4.1™ EQ. Pre EQ Mode is the default EQ. In Pre EQ Mode the ASIO Driver will list the VMS4.1™ device number, the first number in the sequence will be a "0". Please see the window below.
To toggle the Post EQ Mode on and off, proceed as follows: Before powering up the VMS4.1™, press and hold the PFL Cue (4) on the 4th channel MIDILOG and then power on the unit. Release the button, your computer may reinstall the VMS4.1™ as a new device, please allow 10-20 seconds for the change to take place.
PDATE The included version of Virtual DJ includes a Firmware update utility. It is necessary to install this. To update your VMS4.1™, proceed as follows: Please check your computer audio setting and ensure that the VMS4.1™ is not set as a default playback, playback recording, or MIDI device.
You may receive some error windows like you see below: Select proper device in device select window. Please check your computer audio setting and ensure that the VMS4.1™ is not set as a default playback, playback recording, or MIDI device. This will interfere with the update and software applications.
TO YOUR Connect the VMS4.1™ to your PC by using the USB ports located on the rear of the VMS4.1™ and your PC. Connect the supplied USB cable to the USB port on the rear of the VMS4.1™, and the other end connects to the USB port on your computer.
Innofader model which comes with the VMS4.1™ plate cover to protect the Innofader from damage during handling of the VMS4.1™. If you upgrade to the Innofader, please make sure the power is off before upgrading to limit the chance of damage to the Innofader and/or VMS4.1™ during installation.
As manufacturers of products of the brands of AMERICAN AUDIO®, AMERICAN DJ®, ELATION Professional and ACCLAIM Lighting, we are obligated to comply with the ROHS directive. Therefore, as early as two years prior to the directive coming into force, we started our search for alternative environmentally friendly materials and manufacturing processes.
(Registration in Germany: DE41027552) That means that products of AMERICAN DJ® and AMERICAN AUDIO® can be left in the collection points free of charge and they will be used in the recycling program. Products of ELATION Professional, which are used only by professionals, shall be handled by us. Please send Elation products directly to us at the end of their lifetime so that we can professionally dispose of them.
23. S PECIFICATIONS 23.1 G ENERAL Model American Audio® VMS4.1™ - PC Media Controller Dimensions 482(L) x 325(W) x 40(H) mm 19"(L) x 12.75(W) x 1.5"(H) Installation Place on flat surface or mount in flat case Weight 13 Lbs. / 6 Kg...
Need help?
Do you have a question about the VMS4.1 and is the answer not in the manual?
Questions and answers