Advertisement
Application Data
Damper Sideplate and Sleeve Dimensional Data
The drawings below illustrate the factory standard sideplate and sleeve mountings for the SSSMD-201. The standard "A"
dimensions listed in the table provide adequate space for the mounting of actuators and controls.
If space constraints are a problem the "A" dimension can be varied between 5 3 ⁄8 in. (136mm) and 12 in. (305mm).
Sideplate
LH
152mm
.
Right hand drive is show n
Left hand drive available upon re quest
A
305mm *
ML4XXX Series Honeywell
MS4XXX Series Honeywell
MS4120 Series Honeywell
ML8XXX Series Honeywell
MS8XXX Series Honeywell
MS8120 Series Honeywell
331-4551 Siemens
331-2976 Siemens
MK2-7121 Invensys
* For dampers 18 in. (457mm) or more in height these dimensions are 0 in. .
3
3
in. (mm)
All Dampers*
95mm
6 in.
When Height is
V aries
5
3
11 in. (279) or less
with OCI
RH
*With the exception of dampers 10 in. high (254mm) or less.
A
Varies
NOTE: Entire damper frame is not required to be installed
137mm
Sleeve Length
within the wall.
127mm
.
A
Sleeve Length
T*
S
B*
Actuator
Type/Model
1
1
/
in.
2
max.
3
38mm max
/
in.
4
"A" Dimension
Standard
7 3/16 in. (183)
12 (305)
/
in.
8
5 in.
127mm
Space Envelopes Required for
Actuators and Accessories
Externally mounted actuators always require space outside
of the damper sideplate or sleeve. The "S" dimension
illustrates the clearance required for various available
actuators.
On dampers less than 18 in. (457mm) high, actuators
may also require clearances above and/or below the
sideplate or sleeve. "B" and "T" dimensions are worst case
clearance requirements for some dampers less than 18
in. (457mm) high. All damper sizes under 18 in. (457mm)
high do not require these worst case clearances. If space
availability above or below the damper sleeve is limited,
each damper size should be individually evaluated.
B*
With OCI
120 Volt AC
5 1/4 in. (133mm)
3/4 in. (19mm)
6 in. (152mm)
3/8 in. (10mm)
6 in. (152mm)
3/8 in. (10mm)
24 Volt AC
5 1/4 in. (133mm)
3/4 in. (19mm)
6 in. (152mm)
3/8 in. (10mm)
6 in. (152mm)
3/8 in. (10mm)
Pneumatic (psi)
1 in. (25mm)
6 1/4 in. (159mm)
2 3/8 in. (60mm)
12 1/8 in. (308mm)
3 3/4 in. (95mm)
16 1/2 in. (419mm)
Sleeve
Maximum
12 (305)
12 (305)
152mm
.
Varies
127mm
.
A
305mm *
T*
S
With OCI
6 in. (152mm)
6 in. (152mm)
6 in. (152mm)
6 in. (152mm)
6 in. (152mm)
6 in. (152mm)
6 1/2 in. (165mm)
9 1/4 in. (235mm)
10 in. (254mm)
3
38mm max
95mm
137mm
A
127mm
Sleeve Length
Advertisement
