Kyocera KYO110 Quick Start Manual

Bluetooth Headset
A complete user guide can be found at http://www.kyocera-wireless.com/support.
G
ETTING TO KNOW YOUR
AC C J
1 harger ack
E
2 arhook
M F
3 ulti unction Button /
LED I
ndicator
M
4
icrophone
V A
5 olume djust Button
E
6 arpiece
Kit Contents: Bluetooth Headset
Quick Start Guide , and Warranty Card.
C B
HARGING THE ATTERY
Note: The battery must be charged for at least 2 hours prior to use. Once
charged, it provides up to 6 hours of talk time. A tone will sound when the
battery is low.
a. Insert one end of the AC Charger into the AC Charger Jack on
your headset.
b. Plug the opposite end of the AC Charger into a wall outlet.
Note: The LED Indicator will illuminate red while the headset is
charging, and turn off when charging is complete.
c. Unplug the AC Charger from the headset when charging
is complete.
P H
AIRING THE EADSET WITH
Note: Ensure your headset is powered off, and your cell phone is
powered on.
a. Press and hold the Multi Function Button for 6 seconds until the
LED Indicator flashes red and blue. A tone will sound indicating your
headset is in pairing mode.
b. Activate the Bluetooth connection from your cell phone. Execute the
search function to search for Bluetooth devices. When the search
completes, a list of supported devices will be displayed on your cell
phone screen.
Note: The headset will not be detected unless first placed in
pairing mode.
QuickStart Guide
KYO110
82-R2010-1ES, Rev. 001
B H
LUETOOTH EADSET
KYO110
KYO110
, AC Charger,
Y C P
OUR ELL HONE
c. To start the pairing process, select KYO110 from the device list.
d. When prompted select 0000 as the passkey.
Note: Depending on your cell phone, pairing operations may
execute automatically. Please consult your phone user guide if
specific pairing operations are needed.
P B F
ERFORMING ASIC UNCTIONS
P O
OWER N
Press the Multi Function Button for 4 seconds. The LED Indicator will
flash blue.
P OFF
OWER
Press the Multi Function Button for 5 seconds. The LED Indicator will
flash red.
V A
OLUME DJUST
Press the Volume Adjust Button up or down to increase or decrease
call volume.
A A C / E A C
NSWER ALL ND ALL
Press the Multi Function Button.
R A I C
EJECT N NCOMING ALL
Press and hold the Multi Function Button for 3 seconds.
T C
(headset to cell phone / cell phone to headset)
RANSFER A ALL
Press the Multi Function Button for 3 seconds.
R L N
EDIAL AST UMBER
Press the Multi Function Button 2 times. A high tone will sound once a
connection is established.
V D (
phone dependant feature)
OICE IALING
To activate voice dialing, press and hold the Multi Function Button for 3
seconds. To cancel voice dialing, press and hold the Multi Function Button
for 3 seconds.
Note: Review your cell phone user guide for detailed voice
dialing instructions.
FCC N
OTICE
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
C
AUTION
The user is cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void the warranty and users' authority to operate the equipment.
N
OTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/
TV technician for help.
F R E S
CC ADIATION XPOSURE TATEMENT
To comply with the FCC RF exposure compliance requirements, this device must not be
co-located or operating in conjunction with any other antenna or transmitter.
Kyocera is a registered trademark of Kyocera Corporation. The Bluetooth word mark and logos
are owned by the Bluetooth SIG, Inc. and any use of such marks by Kyocera Wireless Corp. is
under license. All other marks are held by their respective owners.
Copyright © 2007, 2008 Kyocera Wireless Corp. All rights reserved.