Advertisement
Available languages
Available languages
O. PARALLEL SPEAKER OUTPUTS - Connect one of four
speaker configurations to meet the 2–ohm minimum load
requirement using any combination of 4–pole Speakon®
and 1/4" output jacks:
1) one 2–ohm speaker
2) two 4–ohm speakers
3) one 4–ohm and two 8–ohm speakers
4) four 8–ohm speakers
P. IEC POWER SOCKET - Connect only the supplied special
high-capacity power cord to a grounded AC receptacle in
compliance with the voltage and frequency ratings
specified on the rear panel of your amplifier.
Q. EFFECTS LOOP - (1) Effects Loop - Connect SEND to the
input of your effects device and the output of the effects
device to RETURN. (2) Multiple Pro™ Amps - Connect
SEND on the primary unit to RETURN on the auxiliary unit.
The primary unit controls all auxiliary units.
The 800 Pro can be mounted in racks and flight-cases
measuring from 15.5 to 22 in (39.7 to 56.3 cm) between front
and rear rails {X} using the adjustable brackets {Y} provided.
1)
TYPE:
PART NUMBERS:
POWER REQUIREMENTS:
PREAMP
INPUT IMPEDANCE:
SENSITIVITY AT FULL POWER:
NOMINAL LEVEL:
POWER AMP
INPUT IMPEDANCE:
SENSITIVITY:
POWER OUTPUT:
TONE CONTROLS
ROOM BALANCE:
BASS/TREBLE:
SEMI-PARAMETRIC EQ:
EFFECTS LOOP
IMPEDANCES:
NOMINAL LEVEL:
FOOTSWITCH:
POWER CORD PART NUMBERS:
RECOMMENDED SPEAKERS:
DIMENSIONS:
WEIGHT:
w w
w
w w
w . . f f e
e n
n d
d e
Rack and Flight Case Mounting
Remove the 2 bolts {Z} on each side of the 800 Pro and
loosely attach the adjustable brackets {Y} as shown.
PR 535
2146800000 (120V, 60Hz) USA
2146806000 (230V, 50Hz) EUR
1800W
PASSIVE:
1M ,
PASSIVE:
19mV,
PASSIVE:
145mV,
10k
1V R.M.S. (0 dBv)
1200W R.M.S. into 2 @ < 0.2 % T.H.D.
±10dB, crossover frequency: 350Hz
BASS:
± 15dB @ 50Hz
LOW FREQ:
25Hz to 150Hz
MID FREQ:
140Hz to 1.6 kHz
HIGH FREQ:
1.4kHz to 8kHz
SEND:
1k
+4dBu (adjustable with level control)
One button: EQ (0055852000)
0059652000 (120V, 60Hz) USA
0059650000 (230V, 50Hz) EUR
2217200000 (810 Pro)
HEIGHT:
3.5 in (8.9 cm)
35 lb (15.9 kg)
Product specifications are subject to change without notice.
e r
r . . c
c o
o m
m
F F
e e
n n
d d
e e
r r
®
8 8
0 0
0 0
F F
e e
n n
d d
e e
r r
8 8
0 0
0 0
R. FOOTSWITCH - Connect the included footswitch to
enable remote on/off switching of the semi-parametric
equalizer.
NOTE: When connected, the footswitch
overrides EQ ON/OFF {I} on the front panel.
S. TUNER OUT - Connect your bass tuner to enable inline
instrument tuning (see MUTE {K}).
T. GROUND LIFT - Disconnects the LINE OUT {V} ground
connection (pin-1) which may reduce noise levels.
GROUNDED (normal)
U. LINE OUT LEVEL - Adjusts the output level of the LINE
OUT jack.
V. LINE OUT - Balanced XLR jack for output to sound
reinforcement/recording equipment.
W. PRE/POST EQ - Supplies the LINE OUT jack with the
signal either before or after it is processed by the
tone/equalization circuits.
PRE (tone/EQ bypassed)
2)
Lift the 800 Pro into position and provide temporary
support until all corners are attached.
3)
Bolt the 800 Pro front panel tabs to the front rack rails.
4)
Slide the adjustable brackets {Y} to fit the rack, then
attach with bolts through the rear rails {X} as shown.
5)
Tighten all bolts securely.
S S
S S
2146803000 (240V, 50Hz) AUS
2146807000 (100V, 50-60Hz) JPN
ACTIVE:
1M
ACTIVE:
40mV
ACTIVE:
300mV
TREBLE:
± 15dB @ 10kHz
LOW LEVEL:
±15dB @ LOW FREQ setting
MID LEVEL:
±15dB @ MID FREQ setting
HIGH LEVEL:
±15dB @ HIGH FREQ setting
RETURN:
22k
0059648000 (240V, 50Hz) AUS
0059651000 (100V, 50-60Hz) JPN
2217100000/2217000000 (410 Pro ST/SL)
WIDTH:
19.0 in (48.3 cm)
w w
w
w w
w . . m
m r
r g
g e
P P
r r
o o
A A
m m
p p
l l
i i
f f
i i
e e
r r
P P
r r
o o
A A
m m
p p
l l
i i
f f
i i
e e
r r
GROUND LIFTED
POST (tone/EQ active)
p p
e e
c c
i i
f f
i i
c c
a a
t t
i i
o o
n n
s s
p p
e e
c c
i i
f f
i i
c c
a a
t t
i i
o o
n n
s s
2146804000 (230V, 50Hz) UK
0059649000 (230V, 50Hz) UK
2217300000 (Bassman 212)
DEPTH:
15.0 in (38.1 cm)
e a
a r
r h
h e
e a
a d
d . . n
7
n e
e t
t
Advertisement
