Table of Contents
Advertisement
OPERATING INSTRUCTIONS (Continued)
START
1.Push in and rotate the Control Knob counter-clockwise to
"ON" position to light burner, continue cycle clockwise -
counter-clockwise rotation of Control Knob until burner
lights. This rotation may need to be repeated several times.
2. Continue to depress the Control Knob for 30 seconds when
burner is lit, then release.
3. If the burner doesn't stay lit, turn Control Knob clockwise to
"OFF" immediately, wait 5 minutes then repeat the
instructions above to light burner.
If burner doesn't light after several tries, consult us by
calling toll-free at 1-888-619-7060 or e-mail us at
technicalservice@allproheater.com for assistance
and advice.
HEAT ADJUSTMENT
1. Turn Control Knob to desired heat setting, anywhere from
HIGH to LOW to get desired heat comfort level.
SHUTDOWN
1. Turn Control Knob clockwise to "OFF" position to shut down
the heater.
2. Unscrew propane cylinder counter-clockwise and remove
when the heater is not in use.
3. Do not relight heater for 5 minutes after the propane cylinder
has been removed.
RESTART
1. Turn the Control Knob clockwise to "OFF" position.
2. Wait 5 minutes.
3. Restart following "START" procedure.
WARNING: FOR YOUR SAFETY
If you smell gas*:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. If odor continues, immediately call
your gas supplier.
*See fuel safety precautions on page 2
of this manual for more information.
STORAGE
1. Allow 45 minutes for the heater to cool down after using,
remove cylinder.
2. Store the propane cylinder in a cool, dry and well-ventilated
area.
3. Store the heater upright in a sheltered area away from
inclement weather and dust.
4. If desired, cover the heater after the heater is cool.
Models
SPC-21PHTTS
MAINTENANCE
To obtain the best performance from your heater, make sure
you perform the following maintenance activities on a regular
basis:
a)
Keep exterior surfaces clean. Use warm soapy water
for cleaning. Never use flammable or corrosive
cleaning agents. Be sure to keep the area around the
burner and control assembly dry at all times.
b)
Air flow must be unobstructed. Spiders and insects
can nest and live in outdoor appliances, especially in
the burners and orifices. This can be a very dangerous
situation. The heater must be inspected for insect
infestation of the burner and orifice annually, or when
one of the following occur:
1) Gas smell along with predominate yellow tipping of
the burner flames.
2) Heater does not reach temperature.
3) Uneven burner glow.
4) Burner makes popping noises during normal use,
other than during shutdown.
c)
Carbon deposits may create a fire hazard. Clean dome
and emitter with warm soapy water if required.
d)
Check your heater for signs of damage or wear and
replace components as necessary.
A hazardous condition may result if a heater is used that has
been modified or is not functioning properly. When the heater is
working properly:
* The flame is contained within the heater.
* The flame is essentially blue with perhaps some yellow
tipping.
* There is no strong disagreeable odor, eye burning or other
physical discomfort.
* There is no smoke or soot internal or external to the heater.
* There are no unplanned or unexplained shut downs of the
heater.
The parts lists show the heater as it was constructed. Do not
use a heater which is different from that shown. In this regard,
use only the regulator cylinder connection supplied with the
heater. Do not use alternates. For this heater, the regulator
must be set as shown in "specifications". If there is any
uncertainty about the regulator setting, have it checked.
A heater which is not working right must be repaired, but only by
a trained, experienced service person. To find the service center
closest to you, visit our website at www.scheuco.com. or call
(888) 619-7060.
You may also obtain in-warranty or out-of-warranty service by
taking the product to your local service center. In-warranty
products will be repaired with no charge for either parts or labor.
Please include a brief statement indicating date, place of
purchase, the nature of the problem and proof of purchase.
Out-of-warrranty products will be repaired with a charge for
parts and labor.
SERVICING
Page -6-
Advertisement
Table of Contents
