Summit Pool Heat Pump Owner's Manual
  1. Manuals
  2. Brands
  3. Summit Manuals
  4. Swimming Pool Heater
  5. Pool Heat Pump
  6. Owner's manual

Summit Pool Heat Pump Owner's Manual

Pool heat pump
Hide thumbs
Table of Contents

Advertisement

Quick Links

Owner's Manual
PRINTED IN CANADA
05/2009

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Pool Heat Pump and is the answer not in the manual?

Questions and answers

Summary of Contents for Summit Pool Heat Pump

  • Page 1 Owner’s Manual PRINTED IN CANADA 05/2009...

  • Page 3: Table Of Contents

    Bonding and plumbing step-by-step instructions Using an External Controller Electrical Connections Wiring Diagram Service Analyzer Control Operation Caring for your Pool Heater Initial Startup Meaning of Display Codes Troubleshooting Requesting Assistance or Service Maintenance Winterizing Pool Heat Pump Warranty OWNER’S MANUAL...

  • Page 4: Introduction

    In general, compared to other types of pool heaters, such as gas or oil- fired, the SUMMIT pool heat pump has a lower heating capacity on a BTU/hr basis. Therefore, it needs to operate for a longer time to accomplish the desired results.
  • Page 5 Please read carefully Record your model’s information Please complete and mail in the ownership registration card provided with this guide. The return address is displayed on the front of your registration card. Simply mail it as you would a postcard. The card helps us notify you about any new information about your heater.

  • Page 6: General Safety Instructions

    General Safety Instructions We care for our customers We have provided important safety messages in this manual and on your heater. Always read and obey all safety messages. IMPORTANT The IMPORTANT sign calls attention to a note that provides important information or information essential to the completion of a task.
  • Page 7 CAUTION All electrical connections must be done by a qualified electrician and according to the local electrical codes. Always cut off the unit’s main power whenever the access panel is open or removed. Always install the machine outdoors (unless otherwise approved by the manufacturer), while respecting the minimal clearances needed for proper operation and heating.

  • Page 8: Installation Instructions

    The SUMMIT pool heat pump is designed for outdoor installation and should not be installed in a fully enclosed area, such as a shed, garage, etc., Recirculation of cold discharged air back into the evaporator coil will greatly reduce unit heating capacity and efficiency.

  • Page 9: Water Piping

    Electrical CAUTION The wiring of your SUMMIT pool heat pump should be performed by a quali- fied electrician in accordance with local requirements. A properly-sized breaker and copper wire must be used.

  • Page 10: Bonding

    Bonding CAUTION Because all metals have different electrical potentials, all metal and electrical components of the pool system must be bonded together. This includes the metal framework of the pool, the light, the pump, the filter (if made out of metal), the heater, any automatic chlorine generator, and any other metal or electrical equipment.
  • Page 11 Bonding and Plumbing diagram Fig. 2 SUMMIT Fig. 3 OWNER’S MANUAL...

  • Page 12: Using An External Controller

    Using an External Controller To connect the electronic board in order to control it remotely, use the P_S terminals on the right side of the board. Next, access the P_S menu and select the desired mode. In internal mode, POOL or SPA mode can be adjusted by using this menu.

  • Page 13: Electrical Connections

    Electrical Connections WARNING The installation of the SUMMIT pool heater should be performed by a certi- fied electrician. To connect the electricity, you must unscrew the five screws of the front panel, then slide the electric cable in the hole located on the left or the right side of the base, and then insert it in the control box.

  • Page 14: Wiring Diagram

    Wiring Diagram COMPRESSOR COMPRESSOR OWNER’S MANUAL...

  • Page 15: Service Analyzer Control

    Service Analyzer Control The control panel is factory set to display the temperature in Fahrenheit degrees. Celsius or Fahrenheit mode Heating mode Compressor ( ) Temperature or fan ( ) running and parameter display Heating mode To raise the desired temperature or to Access to change parameters...

  • Page 16: Operation

    Operation To increase the temperature Push the SET key until you see POL or SPA. The programmed temperature will be displayed. Press the UP arrow to increase the temperature setting one degree at a time. To lower the temperature Proceed as explained above using the down arrow To select the pool or spa mode The unit can keep two temperature settings in memory: one for pool mode (max: 95°F/35°C), and the other for spa mode (max: 104°F/40°C).

  • Page 17: Caring For Your Pool Heater

    Caring for your Pool Heater How to protect your pool heater OWNER’S MANUAL...

  • Page 18: Initial Startup

    Initial Startup IMPORTANT Before starting the pool heater for the first time, it is important to verify that the breaker is in the ON position. Also make sure that the water circulates freely and that the pool pump is activited. Then, you will need to set the water temperature you desire.

  • Page 19: Meaning Of Display Codes

    Meaning of Display Codes Service Analyzer Codes Most problems will be detected by the service analyzer and a code will be displayed on the digital display of your heater. Display Meaning of codes The desired programmed temperature point is lower than 60°F (15°C).

  • Page 20: Troubleshooting

    Troubleshooting The pool heater is not running. Heat pump control set to OFF. Raise temperature set point above 60°F (15°C). Desired water temperature Unit will automatically restart is reached. when the water temperature goes below the set point. Main breaker is tripped. Reset it.
  • Page 21 Ask your electrician to verify your heat pump’s power supply by checking over the L1 and L2 connections in the unit’s service box. There is water around the unit. While your SUMMIT pool heater To check if the water really is a is in the heating mode, a large...

  • Page 22: Requesting Assistance Or Service

    Requesting Assistance or Service IMPORTANT All service will be handled by an Authorized Service Center. Warranty may be voided if service is not done by an Authorized Service Representative. Do not return the heater to your dealer as they do not provide service. Before calling for assistance or service, please check the “Troubleshooting”...

  • Page 23: Maintenance

    Maintenance Dirt can accumulate on the evaporator. You can easily remove it by using a water spray without damaging the small aluminum fins. The cleaning of the plastic cabinet can be done with the help of a brush and soap. Winterizing First, you must turn the breaker off.

  • Page 24: Pool Heat Pump Warranty

    * The 2-year warranty applies only in Canada or within the State of Florida. In the USA, outside the State of Florida, the SUMMIT pool heat pump is warranted for a period of two (2) years for parts and one (1) year for labor.

Table of Contents

Save PDF