Page 4
The information contained in this manual may contain printing errors and is subject to change without notice according to product upgrade. HANA TECH shall not be liable for errors contained herein or for incidental or consequential damage in connection with the furnishing, performance, or use of this material.
Page 5
If the unit is damaged or fails to operate according to the specifications, contact your local distributor or the manufacturer, HANA TECH CO LTD., Hana bldg. 80-1 Songjung-dong, Gumi-shi, Kyung-buk Republic of Korea 730- 090. In the unlikely event the equipment requires shipping back to the manufacturer, please use the original packing material.
Page 6
HANATECH CO., LTD. Safety guideline In order to ensure proper operation and satisfactory performance, observe the cautions listed below. & DANGER This equipment is designed to comply with IEC61 01 1 safety standards, and has been tested for safety prior to shipment. Excessive high voltage measurement or improper operation could result in personal injury, as well as damage to the equipment or the vehicle.
Page 7
For DeN Scanners 11. SAFETY PRECAUT10NS ----------------------- DANGER When an engine is running, keep the workshop area WELL VENTILATEO or attach a building exhaust removal system to the engine exhaust system. Engines produce carbon monoxide, an odorless and poisonous gas that causes slower reaction time and may lead to serious injury or death.
Page 8
The warning messages aboye and the safety messages contained hereinafter cover situations Hana Tech is aware of. Hana Tech cannot know, evaluate or advise you as to al! of the possible hazards.
Page 9
If the product found defective during this period, the product can be returned to Hana Tech and will be repaired or replaced free of charge Freight and repair Cost For the repair of head unit, Hana Tech covers the freight...
Page 10
Warranty Void Even in the effective warranty period, if the problem is found to be caused by any of the followings, Hana Tech charges the cost for round trip freight and actual cost for the service to the customer, and the...
SPECIFICATION ANO PARTS SPECIFICATION ....11. PART LlST ....A.
Page 14
_ _ _ _ _ _ B_H_A_N_A_T_E_C_H_C_O_",_LT_D_"_--' _ _ Specification and Parts S p ec on ----------------------------- ------ Hardware 16bit, 33MHz RAM: 1 Mbyte (SRAM) Program Cartridge Memory: 128Mbytes Flash Memory 16M bytes cards for optional packages Display: 320 240 Monochrome Graphic LCD with Back Light Key Pad: 24 membrane keys, embossing type Serial Port: RS232 Printer: General PC printer...
Page 15
For DCN Scanners C. Oscilloscope Specification (DCN-PRO only) 4 Channel Voltage Division 0.1V - 20V Div Time Division: Normal 25/.15 - 20sec Sampling Rate: 500KHz /2 channel Measurable Voltage: ±150V D. Multi-meter Specification (DCN-PRO only) Voltage: OC 30V Max Frequency: 100KHz Out y Cycle 99.9%...
_ H_A_N_A_T_E_C_H_C_O_.,_U_D_. ___________ 11. Part List ----------------------------------------- Head unit and basic supplies 1. Head Unit (P/N. 1000-0005) Made of strong ABS resin, each unit has passed internal impact test before shipment. As the inner surface coated with anti- electromagnetic interference material neither interferes...
Page 17
Scanners 3. Carry Case (P/N 3003-0003) Provides convenient transportation and the protection of the head unit and other components from outer physical impact during transportation and storage. Carry case provided when purchasing head unit and at least software package together. Includes keys dial...
Page 18
removable by unscrewing for the fuse replacement. It may become loose over repeated use, therefore, it is highly recommended to check if it is tightly screwed frequently. A set of plunger parts are included in the basic supplies Refer to spare parts section hereinafter.
For DCN Scanners Basic supplies for DCN-PRO l. 4 Channel Oscilloscope Adapter (P/N. 3000-0007) Collects and delivers electrical signal from the probes head unit oscilloscope, multimeter and ignition pattern analysis functions. Refer to the manual book further information 2. Probes (P/N.
Page 20
~... _-----8--H-A-N-A-T-E-C-H-C-O-o,-L-T-D-o - - - - - - DANGER Note that the probe has a needle while the Secondary Ignition Probe does no!. These probes with needle get electrical signal directly from the wire therefore, extending them to high voltage lines is extremely dangerous Probe with needle Probe without needle Secondary Ignition Probe...
Page 21
Scanners 5. Ground Cable (P/N 3000-0006) Used for circuit ground while using Scope, Multi-meter and Ignition Pattern functions to get more stable and accurate test result. Highly recommended to extend this cable to the (-) terminal of the vehicle battery always when using these functions Chapte...
:_---------~--. -H-A-N-A-T-E-CH--C-O-.,-U-D-.--~~- Diagnostic Adapters Oiagnostic adapters are sold separately, therefore check if all the adapters you ordered are included in the package upon delivery. There are two types of adapters capsulated and wired types Most of OCN adapters are capsulated for better durability and storage however, sometimes it is difficult or almost impossible to connect the capsulated adapter to vehicle side OLC when it is located deep inside beneath the dashboard...
Page 23
For DeN Scanners 3. Toyota/Lexus 17Pin Semi-circular Adapter (P/N. 3001-0012) Also used the diagnosis of Toyota Lexus generation . . ' ... vehicle side is generally found 1;-. .-. . . beneath the dashboard. Refer to the following warning message -~-- ..
Page 24
ca., HANATECH LTD. --------------------------------------------~ 5. Mitsubishi and Hyundai 12Pin Adapter (P/N. 3001-0001) Used for the communication with Mitsubishi and Hyundai cars of OBO generation 1. A wire type adapter is provided as the connecting difficulties of capsule type adapter in quite a Hyundai cars were...
Page 25
For DeN Scanners WARNING The appearances of this adapter and Toyota 17Pin SEMI-CIRCULAR adapter are exactly same, however, the internal wiring and circuit are different. Check the engraved name and the body color of the adapter carefully before use Improper adapter connection may result serious malfunction of either control system and DCN head unit 8.
Page 26
---------~---H-A-N-A-T-E-C-H-C O- . , L-T-D-.--~~-- • • Kia 20Pin Adapter (P/N. 3001-0004) Used for the communication with Kia cars of OBO generation 1. read & erase and data stream functions are available for the cars with this type of adapter. Refer following warning...
Page 27
For DeN Scanners Holden 6 Pin Adapter(P/N. 3001-0023) Used Australian Holden of OBO generation 1. Japanese cars such as Toyota and Nissan assembled Australia with Holden built engines may have this type of adapter, Vehicle side OLC is generally located beneath the glove box to the...
Page 28
ca., HANA TECH ------------------------------------------~ 17. OBD2 SAE 11850 Cornmunication Module (P/N.3001-0025) To be used with Ford and Austral Holden software packages. Enables communicate with 0802 compliant Ford and Holden Gen 111 for vehicles using SAE J 1850 communication protocols including VPW and PWM 18.
Software Cartridge Contains vehicle information and operating software for DCN scanners The appearance and measurements for DCN cartridges complies with standard PCMCIA, however, inner circuits are of Hana Tech's own designo Therefore, you neither use it with the other equipment nor...
iII'" _ - - - - - B - - H - A -N-A-T-E-C-H-C-O- .,-L-T-D-. _ _ _ _ _ _ E. Spare Parts 1. DeN-seAN Extra fu ses (P/N 3008-0003) For the replacement of the fuse located inside t h e _ cigarette lighter power cable.
Scanners Optional Supplies l. Current Ampere Meter Clamp (P/N 3000-0008) Sold separately for measuring current ampere Made by Summit, Korea 2. Printer Cable (P/N 3000-0009) To be connected between head unit RS232 port and printer to enable direct interface with a PC printer. Compatible with the printers that support PCL mode, and Hewlett Packard ®...
Page 32
OPERATING DeN-PRO GETTING STARTED ..".o Head unit PCMCIACard C. Main OLC Cable Power Supply Contrast 11. CONTROL KEYS ... . B.
For DCN Scanners B. PCMCIA card WARNING Insert or remove PCMCIA card when DCN-PRO power is turned OFF Serious damage to head unit and PCMCIA card may occur in case of insertion or removal of PCMCIA card while DCN-PRO is operating Inserti on Slowly insert the PCMCIA card into the slot and press firmly until it icks into...
Page 36
_---- _H_A_N_ A_T_E_C_H_C_O_.,_L_T_D_ . _ _ 2. Removal Press the eject buUon to release the PCMCIA card from the tight connection with the inside frame and pins Hold the PCMCIA card gentiy and pul! it slowly out of the slot. Chapter...
Page 37
For DCN Scanners C. Main DLC Cable Connection to the head unit The male connectors in both ends of the main OLe cable are exactly same and you can connect any of them to the head unit. Press the main OLe cable connector into the head unit 15 pin female connector, and...
2 __ ----8--H-A-NA-TE-C-H-C-O-.-' L_T_D_. _ _ _ D. Power supply l. Power supplied through DLC adapter 12V battery power is supplied through all OLC adapters except GM/Oaewoo 1 OPin and Mitsubishi/Hyundai 12Pin adapters 2. Cigarette hghter Use the cigarette lighter cable when power is not supplied through the OLC adapter.
Page 39
Scanners 3. Vehicle battery Since the head unit must be placed in the engine compartment when using multimeter, oscilloscope or ignition pattern analysis function, it is necessary to get the power from the vehicle battery. Connect the alligator clips of the battery power cable to the battery terminals of correct polarity.
:_-----8 _H_A_N_A_T_E_C_H_C_O_.,_L_T_D_. - - - - - - ' _ Contrast display is sensitive to the temperature It becomes too faint when it is cold and too dark when it is hot. If the screen is too faint or too dark to read, you can adjust the contrast by turning the contrast dial in the right side of the head unit.
Scanners Keys ----------------------------------- Control A. Keypad keypad is made of chemistry proofing material that prevents contamination damage from hazardous oily workshop environment. membrane keypad designed tested to maintain normal operation over million time key press for each. Each is raised for better tactile feel The keypad has total 24 keys...
Page 42
:_-----~-H-A-N-A-T-E-C-H-C-O-.,-LT-D-.---'- 2. Arrow keys Page Up/Down Seroll Up/ Down Seroll up and down the highlighted bar in the menu by pressing Up/Down arrow keys and press the [ENTER] key to eonfirm theseleetion If the menu has more than 12 items, you may have to seroll up or down the pages to make seleetion You do not have to pound on Up/Down arrow keys to seroll the whole page.
Page 43
For DeN Scanners [-:9:- ] 2. Back light LCD module of DCN-PRO has an illuminating back panel for better legibility in dark or shady places Press this button to turn the back light ON and OFF. 3. ESC Used to abort an operation of DCN-PRO or move to the upper level menu 4.
2003.04 SSANGYONG VEHlC V.550 2003 SAMSUNG VEHICLE V.550 2003.04.21 Should you get any update files from your local distributor or from Hana Tech website, please compare the version number and last update date to check if the update is necessary.
Scanners B. System Test You can test the proper operation of keypad and LCD display. 1. Keypad test A test screen will appear as below when you select [1. Keypad Test] from the menu Press each key of the keypad and check if the color of the corresponding key on the screen turns inverted Following is an example when the [ENTER] key is pressed...
Checks the LCO screen for any defective display. When [2. TEST] is selected, HANA TECH logo appears and you will see the display gradates black and white in and outward as shown below: Should you see any dot, line or blank pixel, please contact your local distributor/.
Page 47
English and Spanish languages are available for selection as of May, 2003. Hana Tech is translating the menu and messages of DCN-PRO to various local languages such as Russian Arabic and Chinese for convenience of non-English speaking customers, and the each language will be provided as an update when the translation is completed.
Page 48
DCN-PRO FUNCIIONS ..... DIAGNOSTIC TROUBLE CODE DTC Read DTC Erase C. DTC Help Tips ..... 11. CURRENT DATA Pulse Signal Type Serial Communication Type C. Data Freeze D. Data Graph Help Tips ..... 4 - 11 111. ACTUATION TEST 4 -14 IV.
HANATECH CO., LTD. DeN-PRO Functions The functions you can choose when all the test vehicle details are selected properly are explained in this chapter of the manual. The actual list of available functions may be différent according to the vehicle you want to test. Diagnostic Trouble Code--------------------- A.
Page 51
For DeN Scanners through the adapter. • e as belo w: nsert Diagnostic Connector. Vchicle Ignit 3. Read Oash Lig~t No OTC: May be blir.king inking 4. In digit DTC ü (~NTERJ PRESS OTC: I72r~ You have to count the MIL flashing on the dashboard and manually input the DTC number to DeN-PRO...
Page 52
:_-----8- _H_A_N_A_T_EC_H_C_O_" _LT_D_, Others Generally DCN-PRO reads DTC pulse signal from diagnostic adapter and shows the DTC number, title and details automatically. 2, Serial Cornmunication type Most of the cars built in 1990's or later support serial communication with a scanner, and the DTC is read by bi-directional communication. DCN-PRO sends a command to the control module to reply with the DTC numbers stored...
For DCN Scanners B. DTC Erase (Clear fault code) l. Pulse signal type Pulse signal type does not support bi-directional serial communication, therefore, a scanner is unable to send a command to the control module to erase the DTC information from memory.
Page 54
HANA TECH LTD. C. OTC Help tips Help tips are provided when you press the [HELP] key after locating the highlighted bar on one of the detected trouble code(s) This function is available when DCN -PRO detects one or more trouble code(s)
For DCN Scanners Current Data ----------------------------------- (= Data Stream, Live Data, Service Data) A. Pulse Signal Type Data stream is not generally supported for this type of old cars because the speed of pulse signal communication is too slow to read the data stream variables Some of old Toyota cars using 17 -pin rectangular adapter exceptionally support data readings as the system supports relatively high speed pulse...
------_~--_H_A_N_A_T_E_C_H_C_O_.,_L_T_D.----~ C. Data Freeze The [Data Freeze] function places the selected data stream variable on top of the LeO screen so that the user can check and compare desired sensor values continually without having to scroll up and down. This function is different from 'Freeze Frame Data' function of Generic OBD2 Step One [~][ ~ and the [A][T] keys...
For DeN Scanners SERVICE DlITr, 02 SE NSOR ------------- ~8:nV 9/J 6 SENSOR ------------ INJECTIO:-¡ TIHE ---- O.2mS ENGINE ----- p :~ "7 SHORT TERM FUEL TRIM LONG RM FL:E:" TRIM SWITCH ------ • ?OW ER STEERI NG SWITCH - lIIR CONCITINER SWI TCH - INJECTION TIME --------...
Page 58
------~--_H_AN_A_T_E_C_H_C_O_.,_~_D_.--~~ ____ For ea eh sensor data graph, the name of the sensor and its eurrent value will be simultaneously displayed together. ehange the sensor, go baek to the previous Serviee Data display by pressing the [Ese] key, and then ehoose other sensors. To halt the graph output, press the [ENTER] key.
Scanners E. Help tips When you press the [HELP] key after locating the highlight bar on a certain data stream variable the help message will be displayed. This works the same for detected Trouble Codes in [Self Diagnosis] function Detailed information including conditional standard range on the selected sensor will be displayed as shown below.
:_-----8- _H_AN_A_T_E_C_H_C_O_.,_LT_D_._----'_ 111. Actuation Test --------------------------------- The actuation test is a very helpful function that temporarily activates or stops a certain actuator such as an injector, a motor or a solenoid by force, so that the user can evaluate the system's condition or the part's normal operation by observing its reaction Signals from various sensors...
Page 61
For DeN Scanners A. Menu Selection Choose [ACTUATION TEST] from the function Selection Menu The name of the actuator to be tested test method and the test condition are shown in the display. Available actuators, test methods conditions may differ in each vehicle B.
Page 62
-- B H-A-N-A T-E-C-H-C-O-.,-L T - D - . - - - In the example below, the injector will stop injecting fuel for 6 seconds while engine is idling, and it will make engine stall or unstable. Testing a fan or an injector is easy to check the proper reaction as it generates distinctive changes in vehicle condition such as fan whining or unstable idling However,...
For DCN Scanners IV. Black Box -------------------------------------- Just like the 'Black Box' or a 'flight recorder' of an aircraft, DCN -PRO can 'record' data stream during the vehicle drive test and the recorded data can be 'retrieved' later for intensive analysis of vehicle's condition This Black function is available with Korean cars only as of May 2003 and scheduled to expand its appl icable range to all car makes befo re the end...
Page 64
:_----8-' _H_A_N_A_T_E_C_H_C_O_.,_L_TD_. B. Memory Check DCN-PRO checks its internal memory befo re it starts recording Black data If the memory is insufficient, DCN-PRO will suggest deleting one or more previously recorded Black Box data sequences DO EC nlem record ¡~ ~!·._ A'o/ eJe :.t!
Page 66
: _ - - - - - 8 H-A-N-A-T-E-C-H-C-O-., _LT_D _. _ - - - - ' _ M ODE:L VEHICLE MOTOR HYllNDAI BOX RECORD B~ACK LOAD/~RJ,SZ E:;TE A list of recorded Black Data will follow for your selection BOX E CORD LOl,D/ ER!\ SALeN 2.
Page 67
For DeN Scanners E. Loaded Blackbox data The loaded black box data has basically the same format the [Service Data (Data Stream)]. See the illustration below. l. Data format In the lower part of the display, the total number recorded frames, frame number before and after...
Page 68
:_---------~-- -H-A-N-A-T-E-CH--C-O-.,-~-D-.--~~ keys. The dotted line indicates from which frame the sensor values are being displayed move it left and right with the keys. The frame number is indicated at the bottom ..SENSOR ",,"' .., • .inrn •• no THR OTILE ON SENSOR·...
Scanners Connector Location --------------------------- The vehicle side OB02 adapter is easy to find as the location is quite regular - under the dash, however, the old vehicle side OLC adapters of OBO generation 1 are located quite randomly and sometimes it is very difficult to find OCN-PRO has the vehicle side adapter location maps for each car make to aid the user in locating the adapters.
Page 70
: _ - - - - - 8 - '-H-A-N-A T-E-C-H-C-O-",-LT-D-"---'- The maps are provided in the order of most frequently found location. Press Up or Oown to view the next or previous map Press the [ESC] key to return to vehicle selection menu ' ¡'I Location maps for Korean cars are based on Left Hand Orive vehicles,...
Page 72
GENERle OBD2 ..... LITERAL DEFINITION OF 08D2 ..... MORE PRACTICAL NOTES A. Technical meaning of OB02 Generic and Enhanced OB02 ..... DCN-PRO and 08D2 111.
Page 74
:_----~-. _H_A_ N_A_T_E C_H_C 0_,_, L_T_D_ ______ _ Generic OBD2 Literal definition of OBD and OBD2------- OBO is an abbreviation for On Board Oiagnostics. OBO-1 is'in reference to Title 13 California Code 1968 titled "Malfunction and Oiagnostic System for 1988 and Subsequent Model Year Passenger Cars, Light-Outy Trucks, and Medium-Outy Vehicles with Three-Way Catalyst Systems and Feedback Contro!."...
Page 75
Scanners JI. More practical notes -------------------------- A. Technical meaning of 0802 l. Standardization For the technicians and scan tool engineers, OB02 has its technical meaning as bringing the standardized methods of vehicle diagnosis to the chaotic aftermarket where dozens of car make different diagnostic adapters and communication protocols their own.
Page 76
:_-----8- _H_A_N_A_T_EC_H_C_O_.,_LT D _ . _ - - - " _ 8. Generic 0802 and Enhanced 0802 1. Generic OBD2 OB02 was implemented for the emission control. Therefore, the standardization is limited to powertrain system that, is directly related to emission control.
Page 77
Scanners much different from OBO generation 1 but only the appearance of diagnostic adapter. This is so called MOBO or manufacturer's OBO In DeN-PRO MOBO communication is supported for all car makes that are included in the coverage list. Chapter 5 -...
Page 78
:_----8- _H_A_N_A_T_E_C_H_C_O_,,_LT_D_, _ _ III. DeN-PRO OBD2 ------------------------ A, Generic 0802 in DeN-PRO 1, General OBD2 You will find General OBD2 category in the top of the car make selection menu in each PCMCIA card of OC N-PRO as shown below, APPLlCATION GENERAL OBD2...
Page 79
Scanners OTAGNOSTTCS OSD 11 DIAGNOSTICS TEST 6Kbp s PWM DETERMINE COMWJNICATION INTERFACE DETERMINE COMMUNICATION INTERFACE OSD TI DIAGNOSTICS DIAGNOSTICS TEST TS09H DETERMINE COMMUNICATION INTERFACE DETERMINE COMMUNICATION INTERFACE When succeeded in communicating with the control module with these standard protocols, DeN -PRO reports successful establishment of communication and waits for your comm and...
Page 80
:_-----8--H-A-N- A -T -H-C-O-.,-L-T- D .-~--- iI!' . . AGNOSTICS l. SELF DIAG RESU~T (D.T.C) OIAG FORMAT C~EAR CCRRE NT Ol\TI, . FREEZ E FRIÜ'1E DJI.T READ NESSS 6. 82 SENSO TEST <... 0VF: case control module does not respond after trying OBD2...
Page 81
Scanners In Europe, EOBD has become mandatory from January 1, 2001, and all the cars built in Europe since then on must have been generic OBD2 compliant. You may select General OBD2 of DCN-PRO for the diagnosis of these brand new European cars for the powertrain system Chapte...
Page 82
JAPANESE CARS TOYOTA and LEXUS 11. HONDA 6 -20 111. NISSAN 6 - 31 IV. MITSUBISHI 6-39 V. MAZDA 6- 52 VI. SUBARU 6- 58...
Page 84
=_-----B--H-A-N-A-T-E-C-H-C-O-,,-LT-D-,----'- Japanese Cars DCN-PRO software package for Japanese cars is provided separately in a 16MB flash memory PCMCIA cardo A few selected international regions have both Japanese and Korean car makes features together in one PCMCIA card The Japanese car PCMCIA card contains a software packag\3 comprising of the following software groups TOYOTA / LEXUS USA or TOYOTA / LEXUS NON-USA HONDA...
Scanners TOYOTA and LEXUS ----------------------- Toyota and Lexus cars share the same scanner communication methods from a scanner's viewpoint. DCN-PRO does not separate Toyota and Lexus in the car make menu beca use the detailed menu selection procedure and other features are exactly same for both marques You can select either Toyota or Lexus in the next step...
Page 86
:_----8--H-A - N-A-T-E-C-H- C -O-.,-LT .-~- 2. Select Model Name You can select between Toyota and Lexus this stage. Toyota non-USA version is applicable to all Toyota cars outside North America. It covers 32 different model variants SELECT VEHICLE MODEL SELECT VEHICLE MODEL l.
Page 87
For DeN Scanners 4. Select model year and other detailed model specifications DCN-PRO may ask for your selection for a few more steps including mod el year, manufacturing plant and the existence of 02 sensor or immobili system to specify the exact vehicle details for precise and accurate results.
Page 88
_~e.I_" _ _ - - - B - H - A N -A-T_EC_H_C_O_.,_LT B. Why so complicated fCA~ When lecting a Camry MCV10 MCV20 with model code MCV20 SXV11 SXV20 VCV10 produced by TMC Product Toyota Motor Compa Others Europe Europe Others Before Aug...
Page 89
For DeN Scanners l. The difference of Toyota from the other apanese cars Japanese cars with the exception of Toyota and Nissan have ID check system. A scanner communicates with an ECM to get the ECM ID number to identify the test vehicle.
Page 90
_--.J_ :_-----B--H-A-N-A-T-E-C-H-C-O-., _LT_D_. 2. How to get the detailed specifications Model Code (Chassis number) Open the engine hood and find the model code stamped into the vehicle specification tag, attached to firewall on the drivE;lr's side Model year and manufacturing plant Model year and manufacturing plant information contained Vehicle Identification Number.
Page 91
Scanners 4. Incorrect Adapter No match in the list Despite detailed vehicle selection procedure of DCN-PRO, you may encounter a situation where you cannot find the correct vehicle details in the list. If you select a similar vehicle model code or other details from the menu an incorrect adapter may be suggested For example...
Page 92
: _ - - - - - 8 - HA-N-A-T-E-C-H-C-O-.,-L-TD-.-.-...-J- Functions l. 17 Rectangular and Semi-Circular Adapter Diagnostic Trouble Code DTC readout is provided in Flash code pulse signals all systems when using this adapter. This old communication type does not allow bi-directional communication between scanner and the ECM simply...
Page 93
For DeN Scanners Supported systems Rectangular Adapter: Generally only Engine and SRS systems are supported with this type of adapter. For the other systems such as ABS, TCS and Cruise Control, only the flash code manual reading is available by counting the relevant Malfunction Indication Lamp blinking when the adapter is connected to the vehicle side DLC.
Page 94
:_-----B-H-A-N-A-T-E-C-H-C-O-o,-LT-D- - - - D. Diagnostic Adapter Location The OLC adapter location drawings are purely from the experience of Hana Tech and provided for your reference only. SELECT VEHICLE MODEL The drawings are based on Right Hand TOYOTA Orive cars, therefore...
Page 96
:_-----8- · _H_AN_A_T_E_C_H_C_O_",_LT_D_ "_ - - - . J _ E" Vehicle Coverage Refer to the following coverage list. (In Alphabetic order) TOYOTA CODE Supported System MODEL KZN185 ENGINE CONTROL RZN180 SRSAIR BAG RZN185 ANTI LOCK BRAKE SYSTEM 4RUNNER VZN130 POWERTRAIN CONTROL MODULE VZN180 IMMOBILlSER...
Page 97
For DeN Scanners AT180 AT200 ST182 ST184 POWERTRAIN CONTROL MODULE ST185 IMMOBILlSER CELlCA ST202 SRSAIR BAG ST204 ANTI LOCK BRAKE SYSTEM ST205 ZZT230 ZZT231 ENGINE CONTROL AIR SUSPENSION CENTURY GZG50 CRUISE CONTROL SYSTEM IMMOBILlSER SRS AIR BAG, BODY CONTROL BB50 POWERTRAIN CONTROL BB58 COASTER...
Page 98
iII'- • :_-----8-H-A-N-A-T-E-C-H-C-O-",-LT-D-"------- AT190 AT210 AT220 POWERTRAIN CONTROL MODULE CT220 ANTI LOCK BRAKE SYSTEM CORONA ST171 IMMOBILlSER ST191 AIR BAG ST210 ST220 ENGINE CONTROL ANTI LOCK BRAKE SYSTEM CRESSIDA CRUISE CONTROL SYSTEM POWERTRAIN CONTROL MODULE CRUISE CONTROL SYSTEM GS151 ANTI LOCK BRAKE SYSTEM JZS1 , ECT,...
Page 101
Scanners POWERTRAIN CONTROL MODULE EMPS ANTI LOCK BRAKE SYSTEM PRIUS SRSAIR BAG CRUISE CONTROL SYSTEM IMMOBILlSER POWERTRAIN CONTROL MODULE SXA10,11 SRSAIR BAG RAV4 ACA20 ANTI LOCK BRAKE SYSTEM ZCA25,26 IMMOBILlSER RAV4 EV SRSAIR BAG ENGINE CONTROL SOLUNA(AFC) AL50 ENGINE CONTROL SPACIO AE111 SRSAIR BAG...
Page 103
For DeN Scanners 1I()~l))\ ---------------------------------------- A. Features of Honda S/W l. Cornmunication Start-up Honda has the ECM ID check system Complicated menu selection procedure as in Toyota is not necessary for Honda cars The user is simply required to check the adapter type of the vehicle to select the adapter and the desired system to test.
Page 104
HANATECH CO LTD. 2. Performance DCN-PRO HONDA software is applicable to all Honda cars regardless of regional market and covers up to 4,000 different system lOs when counting the Engine control system only. Total 7,000 lOs are included in the database for all Honda car systems DCN-PRO Honda software provides original equipment level reliability and accuracy for Honda cars up to 2003 model year.
Page 105
Scanners B. Menu Selection 1. Select HONDA/ACURA Select HONDA /ACURA from the car make menu. APPLlCATION 1. Enhnnced GENERAL OBD2 Generic MULTI- seAN 0802 METER TOYOTA!LEXUS V26C 9¡ J§I.t M NlH V240 NISSANjI NFINITI \12.50 MITSUBI V240 Ml\ZDA SUBARU \'110 s eOPE 5.IGNITION CONFIG...
Page 106
. . . HANATECH CO., LTD. 3. Select Test System Select the system you want to test. SELECT DEVICE ENGINE CONTROL 2.AUTO TRANMISSION 3.SRS AIRBAG 4.ANTI LOCK BRAKE SYSTEM 1- : MOVE ENTER: SELECT Chapter 6...
Page 107
For DCN Scanners Adapters l. 2-Pin Connector 2-pin adapter is generally found together with the 3-pin adapter, however, some old cars may have this adapter only. Uve data (Data stream) is not available for all systems when using this 2-pin adapter. Only reading the flash signal in the dash panel is available with this adapter and bi-directional serial communication with a scanner is not available.
Page 108
iII'· • :_-----8-H-A-N-A-T-EC-H-CO-.-, L_T_D_. _ - - " ' _ _ each adapter is assigned to different systems in the caro You are recommended to try to test the system with 3-pin adapter first, and then try with 2-pin adapter in the event communication using 3-pin adapter fails.
For DCN Scanners D. ECM RESET function Following ECM replacement, fault code erasing or when you feel the necessity to reset ECM adaptation due to poor engine performance, you activate this function It cleans up the ECM memory and makes the ECM ready for self-adaptation. l.
Page 110
:_----8- ~... _H_A_N_A_T_ E_ C_H_C_O_. D_. _ _ _ _ _ _ _ _ _ • Adapter location The location drawings are purely from the experience of Hana Tech and provided for your reference only. The drawings are based on Right Hand Orive cars, therefore, you may have to consider the mirror image for any Left Hand Orive cars.
Page 111
For DCN Scanners F. Vehicle Coverage The vehicle coverage listed below is limited to the cars that supports live data (Data stream Service data) with 3-pin or 16-pin adapter Older cars with 2-pin adapter are not included JAPANESE DOMESTIC 1999 2002 Lagreat Model Name...
Page 112
:_-----~--H-A-NA-T-E-C-H-C-O-.,-L-TD-.----.J- NORTH AMERICAN EUROPEAN Model Name From Until Accord 1994 2002 Accord 1994 2002 Accord V6 1998 2002 Accord 1995 2002 Civic 1992 2002 Acura 1.6EL 1997 2000 Civic Aero 1998 2000 Acura 1.7EL 2001 2002 Civic Coupe 1994 2002 Acura 2.2CL 1997...
:_---------~---HA-N-A-T-E-C-H-C-O- -L-T-D.---~ 111. NISSAN ---------------------------------------- A. Features of Nissan S/W l. Communication Start-up Nissan has neither the ECM ID check system like Honda nor the complicated menu selection system like Toyota. After system selection, the scanner sends a set of commands to the ECM for all data listings available within the vehicle, and then communicates with the ECM for the available items only.
Page 115
For DeN Scanners The system check commands and communication details have been constant without change for both 14-pin and 16-pin diagnostic adapters. Therefore, a scanner does not need to know the ID number or detailed v ehicle pecification Simply s elect t he dapter t ype a nd...
Page 116
ca., HANATECH LTD. Select the adapter type Find the diagnostic connector in the referring to the connector location drawings hereinafter and select the connector type found SELECT CONNECTOR l. 14PIN Connector Connec 3. CONNECTOR LOCATl 1 ..:MOVE ENTER: SELECT Select test system Select system...
Page 118
:_-----8- · ~... A_NA_T E_C_H_C_O_ " L _ T D _ " _ _ _ _ _ _ _ • B. Adapters 14-pin and 16-pin adapters are being used for Nissan cars In North America, Nissan cars of 1995 model year or later usually have 16-pin 0802 adapter while the older cars have 14-pin adapter.
Page 119
Scanners Select IVMS from the system menu as shown above, then DCN-PRO will attempt communication to the IVMS control module If the car has the IVMS system, then DCN-PRO will show you the IVMS item listing If the "Communication Error" message is displayed the system is either not fitted to the vehicle or does not feature self-diagnostics 2.
Page 120
:_---------~---H-A-N-A-T-E-CH--C-O-.,-~-D-.--~~ D. Adapter location The location drawings are purely from the experience of Hana Tech and provided for your reference only. The drawings based Right Hand Orive cars, therefore, you may have to consider the mirror image for any Left Hand Orive...
Page 121
Since the communication protocol for Nissan cars is quite stable with few variations, vehicle coverage is meaningless to list in detail as for Toyota or Honda. The followings are the examples of Nissan models that Hana Tech or its worldwide partners have tested and confirmed its successful communication 200SX,...
:_-----8- ~__.._HA_N_A_T_E_C_H_C_O_.,_LT_D_ _ _ _ _ _ _ _ _ • IV. MITSUBISHI ---------------------------------- A. Features of Mitsubishi S/W Communication Start-up Mitsubishi has the ECM ID check system similar to Honda. Complicated menu selecting procedure as for Toyota is not necessary for Mitsubishi cars The user is simply required to check the adapter type of the vehicle and to select the adapter and the desired system to test.
Scanners 2. Perfonnance Mitsubishi original equipment has various regional versions that cover the Mitsubishi cars in each regional market. DCN-PRO Non-USA version comprises Japanese domestic, Australian, Malaysian and European regional versions. Mitsubishi software covers up to 1,500 different system lOs when counting the Engine control system only.
Page 124
--8--H- A- - C-H-C-O-,- L_T_ D_ 2, Select the adapter type Search for the diagnostic connector in the car referring to the connector location drawings hereinafter and select the connector type you fou MITSUBISHI 1, 12PIN Connector 16Pln Connector Connector 4.
Page 125
For DCN Scanners C. Adapters l. 12-Pin Connector 12-pin adapter is widely used for all Mitsubishi cars of OBO generation It provides the same level of data readings as the OB02 adapter. Read Erase of fault codes, actuation test and data stream are available for all systems except ETACS This adapter is also used for Korean Hyundai and Malaysian Proton cars...
Page 126
HANA TECH CO., LTD. 2. 12+ 16 Pin Connectors Many of Mitsubishi cars manufactured in mid 90 s have both the 12-pin Mitsubishi adapter and OBD2 16-pin adapter. Many Mitsubishi control modules with MELCO system communicate using its conventional protocol, which is not OBD2 compliant even though the vehicle has the OBD2 standard adapter.
Page 127
For DeN Scanners 3. 16 Pin connector 16-pin adapter equates 08D2 standard adapter. Uve data is supported for all systems except ETACS and some early transmissions AII systems in the control system selection menu are covered with this adapter when it is found alone in the vehicle. Chapter 6...
Page 128
__ - ___ 8 __ HA_N_A_T_E_C_H_C_O_.,_LT_D_ _ _ - This page is left blank on purpose Chapter 6...
Page 129
For DeN Scanners O. Unidentified system ID l. System ID Check As explained herein OCN-PRO automatically checks the system ID when you select a control system and sets up the communication with the control module thereupon OCN-PRO Mitsubishi software contains thousands system ID for various regional market specifications, however, it is still possible that you may encounter Mitsubishi cars of which system ID is not...
Page 130
:_----8- • iII!~.. _H_A_NA_TE_C_H_C_O_o_, L_T_D_o _ _ _ _ _ _ 30 Possible incorrect values This is based on the concept that the closest system lOs share the majority of system characteristics with the least differences However, we cannot guarantee the accuracy of data values when choosing an alternative ID.
Page 131
For DCN Scanners E. Communication Error SELECT DEVICE 1. Menu ENGINE CONTROL DCN-PRO always shows 7 control 2. AUTO TRANSMIS I ON SRS AI Bl\.G ANTI LOCK BRl\.KE SYST systems in the menu as shown in ELECTRONI CONTROL SUSPENS TRACTION CONTROL the illustration, however, it doesn't AUTO SYSTEM...
Page 132
=_-----8-' --~.. _H_A_N_A_T_E_C_H_C_O_.,_LT_D_. _ _ _ _ • F. Power supply l. l2-pin adapter Mitsubishi 12-pin adapter has no lights: pin for power supply. You have to use the cigarette lighter power cable to supply power to DCN- PRO head unit when you are -------) using this...
Page 133
Scanners Adapter location • The location drawings are purely from the experience of Hana Tech and provided for your reference only. • The drawings are based on Right Hand Orive cars, therefore, you may have to consider the mirror image for any Left Hand Orive cars •...
Page 134
Toyota or Honda is almost meaninglesso • The following are the examples of Mitsubishi model names that Hana Tech and its worldwide partners have tested and confirmed its successful communication 3000 GT, Carisma, Diamante, Eclipse, Expo, Galant, Lancer, L200, Mirage, Legnum, Libero, Montero, Pajero, Shogun, Space Wagon, etc.
Page 135
Scanners rvi)\~l))\ ---------------------------------------- A. Features of Mazda S/W l. Communication Start-up Mazda has no ID check system like Honda or Mitsubishi. Since the communication protocol is quite simple with few variations, complicated menu selecting procedure as Toyota is not necessary, either. The user is simply required to check the adapter type of the vehicle and to select the adapter and the desired system to test.
Page 136
------_~_' _ H_A_N_A_T_E_CH--C_O_.,_U_D_.--~~-----~.. • Adapters l. Mazda/Kia 6-pin adapter Only the pulse signal type DTC reading function for Engine control system is available when using this type of adapter. MAZDA SELECT DEVICE 6PIN Coonectol 6r:N) (K~a l. ENGINE CONTROL 8PIN nector 1PIN nnector...
Page 138
:_---------~---H-A-N- E -CH--C-O-.,-~ D-.--~~-----~.. • are available for the "B series" trucks Only Powertrain and ABS are available for other models B-SERIES S-SERIES V~HIC¡~S VEHICLE EXCEP~ PCM - CTRL MOD:;:"E PCH - pmIER':RAIN CTRL MODULE PO~IER7RAIN !\NTI ::'C'C BrZ1\KE MOCULE GEM - GEN~RIC ELEC TRO...
Page 139
For DCN Scanners Adapter location • The location drawings are purely from the experience of Hana Tech and provided for your reference only. • The drawings are based on Right Hand Orive cars, therefore, you may have consider the mirror image for any Left Hand Drive cars •...
Page 140
ID check, detailed vehicle coverage like Toyota or Honda is meaningless. • The following are the examples of Mazda model names that Hana Tech and its worldwide partners have tested and confirmed its successful communication 323,626,929 MX3, MX6 Miata Protégé, RX7...
Page 141
For DeN Scanners VI. SUBARU --------------------------------------- A. Features of SUBARU S/W 1. Cornmunication Start-up SUBARU has the ECM ID check system like Honda Mitsubishi. Complicated menu selection procedure as in Toyota is not necessary for Subaru cars. The user is simply required to check the model year and then select system to test.
Page 142
~ HANA TECH ca., LTD. 2. Perfonnance DeN-PRO SUBARU software was engineered and developed in Australia and New Zealand for the cars in this regional market where DeN-PRO provides more than 90% of the original equipment coverage DeN-PRO SUBARU softwBre covers SUBARU cars from 1994 model-...
Page 143
For DeN Scanners B. Menu Selection 1. Select SUBARU Select SUBARU from the car make menu APPLICATION Enhonced 2. Generic MULTI· GENERl\L OBD2 '/201 • seAN OBD2 METER TOYOTA! LEXUS \'26C EONDA/ACURl\ V24C (ú V2SC SSlIN/INFINITI éJi MITSUD IS!H EJCC MAZDA V24C 7.
Page 144
:_-----8--H-A-NA O - . , L-TD-.-----rr-- Select Test S ystem Select the system you want to test SUBARU l. ENGINE CONTROL 2. AUT ISSIO ANTI SKI 4. " P,AG :MOVE ENTER: SELECT z lre s be gr,l ri oll é lclory L() l~l' Ullct...
Page 145
For DCN Scanners C. Adapters l. 9 Pin Connector SUBARU 9 pin adapter is widely used for most of SUBARU cars Trouble code read, erase and data stream are all available through this adapter. 2. l6-pjn OBD2 connector A standard adapter used for relatively new SUBARU cars Trouble code read and erase,...
Page 146
H-A-N -A T -E-C-H-C -O-.,-L-TD-.- - - ' - SRS airbag diagnosis It is said that the manufacturer has designed the system without scanner communication for safety reasons. You are recommended to check the trouble codes manually referring to the following information is al so recommended NOT to test SRS system when using diagnostic equipment for the other systems such as Engine and Transmission.
Page 147
For DeN Scanners and detailed information Function selection menu follows when the [ENTER] key is pressed as shown below: D.T.e CODE LIST ¡ . FA'-:LT con¡:; ¡:;XTRACT 10\1 COD¡:; F.RASURF. NNF.CTOR 1 ..:MOVE ENTER: SELECT Fault code list When selected, DCN -PRO shows the DTC descriptions of Subaru airbag...
Page 148
HANATECH CO., LTD 3. Connector A separate connector is used for airbag system check. When the [4. CONNECTOR] is selected the illustration as shown below follows. Locate the separate 6-pin harness for the SRS airbag under the dash panel referring to the aboye illustration The 6 pins of the connector are numbered as shown below: 61~16...
Page 149
Scanners manually observing the instructions displayed on DCN-PRO screen. Instructions for manually reading DTC of Subaru airbag system are from Hana Tech's experienees only. It is reeommended to refer to th factory manual to extract correet fault eode(s). There are two types of fault code extraction procedu re, and you...
Page 150
:_-----B--H-A-N-A-T-E-C-H-C-O-" _LT_D_, _ - - - - ' _ Turn the ignition key ON without starting engine. Bridge terminal 1 of the 6-pin connector and earth. The SRS warning lamp will begin to flash Long flashes (1 .2 sec) indicate the [Tens] of the DTC, and the short ones (0.3 sec) indicate the [ones(units)] Long signal Short signal...
Page 151
6-pin separate connector manually observing instructions displayed on DCN-PRO screen Instructions for manually reading DTC of Subaru airbag system from Hana Tech's experiences only. It is recommended to refer to the factory manual to extract correct fault code(s).
Page 152
HANATECH CO., LTD. among these two in the menu that follows as below: D.T.e: ALL !XCEPT 2.2L (EJ22) LID~R~Y L13E~T~ (::: ,122 MOVE ENTER: SELECT ALL EXCEPT LlBERTY 2.2L (EJ22) Select this item from the menu to erase fault code(s) Subaru cars except Liberty...
Page 153
Scanners ON and OFF on regular intervals. LlBERTY 2.2L (EJ22) Select this item from the menu to erase fault code(s) of Subaru Liberty 2.2L(EJ22). Following instruction will appear. Swi tch ignition OfF. move Fuse One Minute. Turn the ignition key OFF. Remove Fuse #25 for one minute.
Page 154
When DeN-PRO encounters a system ID that is not included in its data base, it shows the detected system ID and communication features If you encounter these systems, contact your local distributor, and the system ID will be relayed to Hana Tech for a future update. Chapter - 71...
Page 155
For DeN Scanners F. Adapter location The location drawings are purely from the experience of Hana Tech and provided for your reference only. The drawings are based on Right Hand Orive cars, therefore, you may have to consider the mirror image for any Left Hand Orive cars.
Page 156
KOREANCARS ..... BACKGROUND ..... 11. REGIONAL DIFFERENCES ..... 111. HYUNDAI ..... 7 -16 IV. KIA ..... 7 -28 V. DAEWOO VI. SSANGYONG 7 -40 VII. SAMSUNG...
From a scanner's viewpoint, the genealogical chart of Korean cars is very much complicated and it is difficult to provide sufficient coverage Hana Tech, the manufacturer of DCN -PRO has been developing aftermarket scan tools from the very beginning of the fuel injection history of...
For DCN Scanners JI. Regional differences -------------------------- Hyundai and Kia, the best selling Korean car makes, are manufacturing the cars differently to meet the emission related regulations of regional markets According to the target markets, cars of these two companies are categorized into three groups: Korean domestic, North American and Non-USA exports Daewoo, Ssangyong and Samsung cars do not have such regional variations.
Page 160
HANATECH CO., LTD. D. Used cars A real problem is in developing countries where Korean secondhand cars share big market portion In these countries, the user may have to try all three regional versions unless he knows where the car is originated E.
Scanners 111. HYUNDAI ------------------------------------- A. Vehicle Model Selection l. Korean Domestic In export markets, Hyundai has kept using a constant model name for certain model quite long identifying the details by the model year. To the contrary, in Korean domestic market, Hyundai has named the same model differently after applying a slight change in design system.
Page 162
HANA TECH CO., LTD. Since the model names are so diversified, you do not have to select a model year when you are testing a Hyundai of Korean domestic version. It is directly followed by the system selection. APPLICATION GENERAL...
Page 163
For DeN Scanners 2. USA NON-USA Exports As explained above, in export market, Hyundai and Kia maintained the same model name quite long, therefore, it is necessary to specify the model year and other details to successfully establish communication with the control module A detailed model name and model year listings are provided for your selection, and followed by the system selection.
Page 164
HANA TECH CO., LTD. 3. Model name comparison chart <Based on Non-USA Exports> Domestic Model Name Export Model Name ATOS ATOS GETZ CLlCK ACCENT 2003 NEW VERNA ACCENT 2000-2002 VERNA ACCENT or ECXEL 1995-1999 ACCENT EXCEL 1990-1994 EXCEL SCOUPE 1-1996...
Page 165
Scanners B. System Selection l. Select test system When the model name and model year selections are made, DeN-PRO proceeds to system selection menu. DeN-PRO shows all possible systems that are available with the selected vehicle The menu generally has multiple Engine types for selection Any system shown in the menu does not mean that DeN-PRO confirms actual existence of the system in the...
Page 166
ca., HANATECH LTD. 2. Engine type When an engine control system is selected, another engine specification selection menu follows as shown below: :';t.~ '.A') ¡. L2:Af; ALL . UN LEAD E080 UNLEAD 080-11 t ..: MOVE ENTER : SELECT There is a variety of engine specification according to the engine size, model year, fuel type and regional emission regulations.
Page 167
For DeN Scanners 3. Uncertain details Trial and error is easy to know the engine size, model year and fuel type, however, identifying the applied emission regulations is difficult for independent workshop technician. The other control systems such as ABS and SRS also may ask your further detailed selection as below:...
Page 168
HANATECH LTD. CO., 4. Irnmobilizer DCN-PRO supports following functions for immobilizer system of Hyundai and Kia cars. Diagnostic Trouble Code Data stream Password Record/Change Master Key Record/Change Master Key Delete Neutral Mode Immobilizer Reset It is highly recommended to get the authorization for the access...
Page 169
For DCN Scanners C. Functions Refer to the previous chapter for the details of following functions of Hyundai software Diagnostic Trouble Code Current Data (Data Stream) Actuation Test Help Tips / Repair guide Black box (Flight record) Chapter...
Page 170
HANA TECH LTD. D. Diagnostic Adapter Location The DLC adapter location drawings are purely from the experience of Hana Tech and provided for your reference only. The drawings are based on Left Hand Drive cars, therefore, you may have to consider the mirror image for the Right Hand Drive cars.
Page 171
Scanners Atos, Elantra('96-), Sonata('99-), Export XG, Accent(2000-), Matrix, Trajet, name SataFe, Centennial, H-1 Truck Atos, Avante, Avante Domestic Sonata, Sonata, ¡::> • <::: name Grandeur XG, Verna, Lavita, Trajet Santa Fe, Equus, Libero '<;¿ Adapter type: 0802 16-pin Adapter Sorne of Avante (Elantra 96-00) have 12-pin adapter.
Page 172
HANA TECH CO., LTD. E. Coverage Al! Hyundai cars Chapter 7 -...
Page 173
Scanners l\!. lCIJ\---------------------------------------------- A. Vehicle Model Selection Model Name Kia's model naming practice is no less complicated than Hyundai names most of their cars differently in export domestic market And th ey even name a same car differently according to the target market. This brings about confusion in...
Page 174
HANA TECH CO., LTD. Model Name Export Domestic Rio SF DeN-PRO Model selection Non-USA / USA Domestic Rio / Rio SF Model Name Export Domestic Sephia Sephia Sephia 11 Mentor DeN-PRO Model selection Non-USA / USA Domestic Sephia / Sephia 11...
Page 175
Scanners Model Name Domestic Export Shuma 11 Spectra Wing Spectra DCN-PRO Model selection Domestic Non-USA / USA Spectra Shuma Model Name Export Domestic Carens Carens DCN-PRO Model selection Domestic Non-USA Carens Carens Model Name Domestic Export Sportage Sportage DCN-PRO Model selection Domestic Non-USA Sportage...
Page 176
HANATECH CO., LTD. Model Name Export Domestic Optima Optima Magentis Optima Regal DeN-PRO Model selection Non-USA Domestic Optima Optima( Magentis) Optima Regal Model Name Domestic Export Elan Elan (Lotus) DeN-PRO Model selection Domestic Non-USA Elan Elan Model Name Domestic Export Potentia Potentia DeN-PRO Model sel ection...
Page 177
Scanners Model Name Domestic Export Sedona Carnival Carnival DCN-PRO Model selection Non-USA / USA Domestic Carnival Carnival(Sedona) Model Name Domestic Export Military 4WD Retona KM42 Series DCN-PRO Model selection Domestic Non-USA Retona Retona Model Name Domestic Export Carstar Joice DCN-PRO Model selection Domestic Non-USA Carstar...
Page 178
HANA TECH CO ., LTD. Model Name Domestic Export Bongo Truck Frontier Bongo Frontier K2700 DCN-PRO Model selection Non-USA / USA Domestic Frontier Frontier Model Name Domestic Export Sorento Sorento DCN-PRO Model selection Domestic Non-USA / USA Sorento Sorento...
Page 179
Scanners B. System Selection Select test system When the model name and model year selection is made, DeN-PRO proceeds to system selection menu SELEC7 VEinCLE MODEL O?TIMA{MAGENTIS) i?HIDE 2000 - 200 [-¡ VISTO 2002 I\VELLI\ 3. 2003 MY SSPHIA :-H.; !·~l\ CM'.SNS SPC"TlIGS...
Page 180
HANA TECH CO., LTD. 2. Engine type When an engine control system is selected, another engine specification selection menu follows as shown below: ENGiNE L4-S011C l. UNL:::AD Gi;N "j '.r; ¡ P.l. UNLEA F~ ~-~ UNi.:=-:¡, }-o. t ... :...
Page 181
It is highly recommended to get the authorization for the access to th immobilizer system from the car manufacturero HANA TECH is not liable for any damage or loss caused by misdirected improper use of immobilizer functions by the unauthorized personnel.
Page 182
HANATECH CO., LTD. Functions Refer to the previous chapter for the details of foliowing functions of Kia software Diagnostic Trouble Code Current Data (Data Stream) Actuation Test Help Tips / Repair guide Black box (Flight record) Chapte...
Page 183
For DeN Scanners D. Diagnostic Adapter Location The DLC adapter location drawings are purely from the experience Hana Tech and provided for your reference only. may have to The drawings are based on Left Hand Drive cars, therefore consider the mirror image for the Right Hand Drive cars.
Page 184
HANATECH CO., LTD. Export Ford Festiva, Captial, Concord name Domestic Pride, Avella, Capital, Concord name <:: Adapter KIAlMAZDA 6-pin Adapter type: Type Carens, Potentia, Credos (Clarus), Sportage, Shuma (Sephia), Elan, Export Carnival (Sedona), Rio, name Retona (KM42), Enterprise Sephia 11 Shuma 11, Sorento, <:: Optima (Magentis)
For DeN Scanners l)j\~~()() ------------------------------------- A. Vehicle Model Selection Regional Variation Differently from Hyundai or Kia, Daewoo has no regional variations. Korean domestic version software compatible with export models, too. Therefore, DCN -PRO Korean car software package includes Daewoo domestic version codes only. APPLICATION E:<J\:' f:YU~': JI\...
Page 186
HANATECH CO., LTD. Cielo Daewoo renamed Lemans to Cielo after face-lifting. Cielo was al so manufactured in their overseas plants in India and Uzbekistan Both of "Cielo" and "Heaven" were used for export models Lemans and Cielo were replaced by Lanos in 1997. Ssangyong cars Ssangyong cars once had be en sold through Daewoo dealer networks few years in late 90's, and most of Ssangyong...
Page 187
For DeN Scanners B. System Selection 1. Menu Selection A system selection menu promptly follows the model name selection. DCN- PRO Daewoo software does not require you to make selections among complicated model codes and applied emission regulations. A simple engine size and model year selection menu follows when [Engine control] system is selected.
Page 188
HANATECH CO., LTD. 3. Supported systems and coverage Model Name ENGINE .,¡ LEMANS (RACER) .,¡ .,¡ .,¡ ESPERO .,¡ .,¡ NEW PRICE / SALaN .,¡ .,¡ .,¡ CIELO (HEAVEN) .,¡ .,¡ .,¡ NEXIA .,¡ .,¡ .,¡ .,¡ LANaS 1/11 .,¡ .,¡...
Page 189
For DeN Seanners D. Diagnostie Adapter Loeation The OLe adapter location drawings are purely from the experience of Hana Tech and provided for your reference only. The drawings are based on Left Hand Orive cars, therefore, you may have consider the mirror image for the Right Hand Orive cars. view these drawings on the OCN-PRO screen by selecting [3.Connector Location] after selecting [OAEWOO VEHICLES] from the...
ca., HANATECH LTD. Model Name Damas Labo • <:: DAEWOO 12-pin Adapter type: Model Name Matiz DAEWOO 12-pin Adapter type: Lemans(Racer), Espero Model Name Price Salon Cielo(Heaven), Nexia Tico Lanos, Nubira DAEWOO 12-pin Adapter type :¡ E. Coverage Al! Daewoo cars Refer to the [8 Supported Systems Coverage] for further information...
For DeN Scanners VI. S SAN G Y O N G -------------------------------- A. Vehicle Model Selection l. Regional Variation Ssangyong has no regional variations Korean domestic version software compatible with export models Therefore, DeN-PRO Korean car software package includes Ssangyon domestic version codes only.
Page 192
HANA TECH LTD. SE:,ECT VEHICLE ~IODF;T, KORf.,NDO CHAIKMAN RF.XTON t .-.. D!TER SHEeT MOVE Chap 7 - 35...
Page 193
For DeN Scanners B. System Selection A system selection menu promptly follows the model name selection DCN-PRO Ssangyong software does not require you to make selections among complicated model codes system version and applied emission regulations at this stage. When a system is selected a detailed specification menu follows.
Page 194
HANATECH CO. LTD. Supported systems Model Name TCCU MUSSO ISTANA(MB100) KORANDO CHAIRMAN REXTON D. Function Selection Daewoo cars support DTC read / erase and data stream fun ction ease refer to the previous chapter for detailed operation ch function TCCU system may support DTC reading function onl Chapte 7 - 37...
Page 195
For DeN Scanners E. Diagnostic Adapter Location The OLC adapter location drawings are purely from the experience of Hana Tech and provided for your reference only. The drawings are based on Left Hand Orive cars, therefore, you may have to consider the mirror image for the Right Hand Orive cars.
Page 196
HANATECH CO., LTD Model Name Chairman 14-pin circular Adapter type: You have to remove the plastic cover Model Name Istana (MB100) 14-pin circular Adapter type: This drawi is based passenger have access adapter through engine compartmen for this kind of van. Model Name Musso, Rexton...
Scanners VII. SAMSUNG A. Background Renault-Nissan-Samsung Samsung motor company's official name is Renault-Samsung motor company, and is a family of Renault-Nissan network, and manufactures knockdown models of Nissan cars in the assembly plant in Korea Samsung has two models of SM5 and SM3 which the same Nissan Maxima and Bluebird.
Page 198
HANATECH CO., LTD C. Diagnostic Adapter Location Samsung cars use 14-pin Nissan adapter found in only one location. • 14-pin Nissan adapter Model Name (SQ5), 14-pin Nissan Adapter type: Ch<Ipter 7 - 41...
Page 200
GAS ANALYSER INTERFACE ..... SETUP Power Supply Cabling C. Power supply to DCN-PRO ..... OPERATION Remote Control Mode Data Stream Mode...
Page 202
---------~ CO_._,_~_D_. _H_A_NA __ TE_C_H __ Gas Analyser Interface DeN-GAS 4/5 G Analyser The interface between the scanner and the gas analyser is available between DCN -GAS 4/5gas analyser IM-2400 and DCN-PRO or SCAN scanner. HOST- PRO optional package is al so necessary to add the real-time PC interface features.
Scanners l. Set up ------------------------------------------- A. Power supply Refer to DCN-GAS analyser manual when using the analyser alone without interfacing with the scanner. This chapter explains the operation when the gas analyser is used in the vehicle interfaced with the scanner. Connect the cigarette lighter power cable to the cigarette lighter...
lB iII'" : _ _ _ _ _ _ B_,_HA_N_A_T_E_C_H_C_O_o,_L_TD_o _____ Cabling -- - l . . printer • '-----1 Scanner Gas analyser interface Connect the 15-pin male connector of gas analyser split cable DCN-PRO RS232C adapter, Connect the 9-pin female connector to the gas analyser.
Page 205
Scanners 2. Adding Printer to the network You may print the actual measurements of gas reading as well as the scanner data stream values any time when the two equipments are interfaced by pressing the [PRINT] key of DCN-PRO Connect the printer cable that is supplied as an optional part of DCN- PRO to the 15-pin female adapter of the split cable.
Page 206
. . . ca., HANATECH LTD. Connect the USB cable to the PC 9-~pi_n ~~ Split car-b_le _ _ _ _ _ _ _ _ _ Gas Analyser I~Ui 15-pin~ <®> 15-pino USB(-) .. - ~.~---------~ USB Module USB Cable L -_ _ _ _ ---l HOST-PRO is also supplied as an optional package for DCN-PRO If a printer is installed to the PC, you can print out the measurements...
Page 207
For DCN Scanners C. Power supply Connect one end of the secondary power cable that is supplied with the gas analyser to the auxiliary power socket of cigarette lighter plug, and the other end to DCN-PRO. apte...
TE_C_H_C_O_. _ ,_~ ___________ ___ H A_NA __ ____ Operation --------------------------------------- There are two ways you can get the gas readings using scanner interface: Remote control mode DCN-PRO works as a remote control module. AII screenplays of the gas analyser are transferred to DCN-PRO and you can control the operation of...
For DeN Scanners A. Remote control mode Basically, all the functions and screenplays are the same as when using the gas analyser alone. You can simply regard that the front control panel af the gas analyser has transformed ta DeN-PRO l.
___________ ___ H_A_N_A_TE C _H .,_LT _D_. _____ B. Data Stream Mode DeN-PRO works as a data receiver. Gas readings are provided as a part of data stream You can view both of scanner data stream information and gas measurements at the same time with DeN-PRO Gas readings are listed in the last part the scanner data str~am...
Page 211
For DeN Scanners With or without gas readings When you select [Service Data (=data stream, live data)] from the function menu following query follows when the gas analyser is interfaced with DCN PRO. In case these two machines are not interfaced, DCN-PRO will skip this menu selecting procedure.
Page 212
. . . ca., HANA TECH LTD. ------------------------------------------------~------ 2. Data stream with gas readings Gas readings are available only when the gas analyser is properly interfaced with DeN-PRO and ready for data transmission Refer to the gas analyser manual for further information You can find the gas readings in the end of data listing Use [.Á.] and [ ..
Page 213
For DeN Scanners 3. Data Freeze Graph You can place up to 5 sensor or gas readings on the top of the screen by pressing the [ENTER] key after locating the highlighted bar on the item The selected items remain in the top of the screen while you are scrolling up and down the screen to view other data readings •...
Page 214
_ H_A_N_A_T_E_C_H_C_O_ _ ~_D_ ___________ 4. Black Box Record You can download both of scanner data and gas readings to DCN-PRO memory using this function Black function of DCN-PRO scanner works the same in the gas analyser interface mode, too Refer to [Chapter 4.
Page 215
For DeN Scanners 5. Host-Pro By utilizing HOST-PRO realtime PC interface optional package, you can view the live data stream and gas readings on your PC screen also replay the saved balckbox data. Refer to the separate HOST-PRO manual for further information of the functions and features Data Stream...
Page 216
TROUBlE SHOOTING OCN would not turn on when the power key is pressed Power automatieally turns off after turned on Power doesn't turn off even the power key is pressed Improper response to key input LCO sereen problems 1 LCO sereen problems 2 System failure System breaks down after showing DCN logo Continuous beep sound and erratic display...
Page 218
HANATECH CO., LTD. Trouble Shooting This part of manual presents you the instant actions to be taken for the most frequently reported troubles The purpose of this troubleshooting guide is to minimize the loss of time and cost caused by disputing of troubles that can be simply sol ved by the user himself.
Page 219
Scanners DeN would not turn on when the Power key is pressed Check the power cable connection properly connected YESo The cable is firmly connected Reconnect power cable firmly still does not Check if red LED's on both ends of power cable are 80th LED's Only...
HANATECH CO., LTD . . . Power automatically turns off after turned on Check if the user pressed Power key continually sound stupid, but actually happens there. the user presses the "Power" key too long, recognizes the long input signal as a turning off command Press the Power key shortly to turn on YESo...
Scanners Power doesn't turn off even the Power key is pressed Check if the user pressed Power key shortly the you press the "Power" key too short, DCN does not recogni the key input signal as a turning off command Keep pressing the Power for more...
HANATECHCO., LTD. Improper response to Key input Keypad Test case trouble with the keypad operation, please do keypad test. Press Irom the initial m enu go to the conliguration menu Choo ypad test] unction. Reler to Chapter 3. Some of the keys are not working AII keys working properly...
Page 223
For DeN Scanners screen problems The display is too dim or too dark Adjust the contrast using the contrast wheel on the right side of DeN scanner stands for Liquid Crystal Display, is very sensitive to temperatu re. you have placed scanner a cold or hot place,...
Page 224
HANATECHCO, LTD ..screen problems When you press the [Backlight] button marked [ the backlight must turned-on with faint ticking sound. Please contact your !ocal distributor for furlher assistance if the key doesn't work Report to your local disributor Your local distributor must check...
Page 225
For DeN Scanners System fails promptly after showing the DeN logo System fails with continuous BEEP sound and erratic display Remove power then turn ON again il doesn'l work. slops aga in. Remove power. Remove the cartridge from slot then Turn power ON hing differen!.
HANATECHCO.,LTD. ' " "INVALlO NANO FLASH" Error n an error message appears as be low as soon as turning head unit. ERROR! INVALlO NANO FLAS CANNOT REAO ROM INFO CHECK PROGRAM CARO Turn the power off, Remove the cartridge and insert it again firmly Ensure that the upper side of the...
Scanners "This card needs scope upgrade" Error When an error message appears as below as soon as lurning Ihe head unil. THIS CARO NEEOS SCOPE UPGRAOE PRESS [ENTER] ANO CONTINUE UPGRADE This error message is saying Ihallhe cartridge's software is very old and has never been upd aled a long lime.
Page 228
HANATECH CO., LTD .."Card Rom Version is different" Error When following error message appears as 500n as turning the head unit CARO ROM VERStON IS OIFFERENT YOU WANT RELOAD? Update internal ROM memory These errors occur when the software version interna...
For DeN Scanners Broken characters and erratic display When illegible unknown symbolic characters or erratic dots or lines appear on screen after ding a program Check the same symptom with the other cartridges AII cartridges have the same prob Only one cartridge has the problem Choose "2.
H A N A T E C H C O . , L T D . ' " Communication Error Check the cable connection Check the followings The DCN main data link cable is firmly connected DCN main unit correct adapter is firmly connected to the DCN main data link cable adapter...