Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ovislink AirLive ePhone-1000
Summary of Contents for Ovislink AirLive ePhone-1000
- Page 1 AirLive ePhone – 1000 VOIP IP Phone User’s manual...
- Page 2 Safety Instructions Safety Instructions Do not attempt to service the product yourself. Any servicing of this product should be referred to qualified service personal. To avoid electric shock, do not put your finger, pin, wire, or any other metal objects into vents and gaps. To avoid accidental fire or electric shock, do not twist power cord or place it under heavy objects.
-
Page 3: Safety Notices
Safety Notices These are the safety considerations for using the AirLive ePhone-1000. Read these notices before installing or using the phone. Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. - Page 4 Warning This product relies on the building's installation for short-circuit (over current) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors). Warning The device is designed to work with TN power systems.
-
Page 5: Table Of Contents
Front Panel ..............................9 Rear and Back Panel ..........................10 Function Keys ............................11 HARDWARE INSTALLATION 12 CONFIGURING THE AIRLIVE EPHONE-1000 WITH THE KEYPAD Configuring Network Settings....................... 14 Configuring for DHCP ............................14 Configuring for Static IP............................14 Configuring for PPPoE ............................15 Protocol Settings ............................ - Page 6 PROTOCOL PARAMETERS PHONE PARAMETERS AUDIO PARAMETERS OTHER PARAMETERS SAVE/REBOOT PARAMETERS 37 Registration Message..........................38 USING AIRLIVE EPHONE-1000 To make a phone call ..........................39 Review call record ..........................39 Speed Dial..............................39 Mute ................................40 Hold ................................40 APPENDIX 41...
-
Page 7: Product Specifications
Product Specifications Voice Call Control Protocol SIP (RFC-3261) or H.323 V4 Voice Compression G.711 A/µ -Law, G.723.1, G.729A/B/AB Echo Cancellation G.165 16ms Delay (Point to Point) < 100ms Average Bandwidth Requirement 10-12k bit/s Network Protocol RTP/RTCP, UDP/TCP Support Silence Suppression 、VAD, CNG、Acoustic Echo Cancellation、Jitter Buffering DTMF tone detection E.164 Dial plan... -
Page 8: Package Contents
Package Contents The AirLive ePhone-1000 Series VoIP phone package contains: • One AirLive ePhone-1000 VoIP phone • One power adaptor • One RJ-45 Ethernet cable • Quick Installation Guide • Installation CD - 8 -... -
Page 9: Airlive Ephone-1000 Functions
AIRLIVE EPHONE-1000 Functions Front Panel - 9 -... -
Page 10: Rear And Back Panel
Rear and Back Panel Power Jack 10 Base T Ethernet RJ-45 Jack Microphone Jack Earphone Jack Wall Mount Handset Cord Jack Microphone - 10 -... -
Page 11: Function Keys
With handset hung, press the IP key to get local IP address of the phone. Mask With handset hung, press the Mask button to get the subnet mask of the AirLive ePhone-1000. GATE IP With handset hung, press the GATE IP button to get the gateway IP address in LAN. -
Page 12: Hardware Installation
Hardware Installation Plug the power cord into the Power jack of the AirLive ePhone-1000 VoIP Phone. Plug the RJ-45 Ethernet cable into the Ethernet jack. Plug the other end of other cable into the HUB, Router, ADSL Modem, or other broadband device. -
Page 13: Configuring The Airlive Ephone-1000 With The Keypad
Configuring the AIRLIVE EPHONE-1000 with the Keypad AirLive ePhone-1000 can be configured with its keypad or on a web page. The table below illustrates Configuration Function keys: Keys Function SPD./HOLD Change Settings REDIAL/MUTE Main Menu Options Vol - Next Page... -
Page 14: Configuring Network Settings
DHCP is the default setting for the AirLive ePhone-1000. This setting enables internet connections with any DHCP environment. If either PPPoE or Static IP are used, change the default network setting of AirLive ePhone-1000 to one of these network environments. -
Page 15: Configuring For Pppoe
Configuring for PPPoE Connect the power adaptor to the AirLive ePhone-1000. Connect the PPPoE network to the AirLive ePhone-1000 to its RJ-45 port. Press1, 2, 3, 4, # (Hold the “#” key) enter a [Password] Press 1, 2, 3, 4 and Enter→ the Network Settings option appears. -
Page 16: Protocol Settings
Press SPD/Hold Enter the IP address of the STUN server (XXX*XXX*XXX*XXX) and press Enter. To Configure the AirLive ePhone-1000 Registration Type At the [protocol settings] prompt, press Enter once Press Vol. + (the volume up button) multiple times→ [local type] appears... - Page 17 Enter. • Press “1” and Enter. Continue with step 7 and 8. To Configure the AirLive ePhone-1000 server account number At the [protocol settings] prompt press enter multiple times→ [account] appears Press SPD/Hold→ input server account number (XXX) and then press Enter To Configure the AirLive ePhone-1000 server Account Password At the [protocol settings] prompt press Enter multiple times→...
-
Page 18: Audio Settings
Press 1, 2, 3, 4, # (Hold the “#” key) → Press Vol.+ 3 times→ [Audio Settings] appears. To Configure the AirLive ePhone-1000 voice compression Codec Type: At the [audio settings] prompt press Enter once→ [audio type] appears → press SPD/Hold •... -
Page 19: Other Settings
Other Settings To Access the Other Settings Menu Press 1, 2, 3, 4, # (Hold the “#” key) → [Password] appears Press 1, 2, 3, 4 and press Enter→ Network Settings appears → Press 1, 2, 3, 4, # (Hold the “#” key) →Press Vol.- multiple times→ [other settings] appears To Change the User Password At the [other settings] prompt press Enter once→... -
Page 20: Speed Dial Settings
Press SPD/Hold to select the first speed dial number and press Enter Press Enter again→ [number1] appears Press SPD/Hold Enter the first set of telephone numbers and press Enter. Repeat step 2 to store more numbers. The AirLive ePhone-1000 can store up to 100 speed dial phone numbers. - 20 -... -
Page 21: Revert Back To Factory Default
Revert Back to Factory Default Press 1, 2, 3, 4, # (Hold the “#” key) → [Password] appears Press 1, 2, 3, 4 and press Enter→ Network Settings appear Press 1, 2, 3, 4, # (Hold the “#” key) →Press Vol.- multiple times→ [Default Settings] appears Press Enter→... -
Page 22: Storing Settings
Storing Settings When all settings have been entered to configure the AirLive ePhone-1000 you will want to store them. Press 1, 2, 3, 4, # (Hold the “#” key) → [Password] appears Press 1, 2, 3, 4 and press Enter → Network Settings appears Press 1, 2, 3, 4, # (Hold the “#”... -
Page 23: Editing Settings
Editing Settings To change or add settings you have stored you can load and review each of the parameters that have been set and edit them. Press 1, 2, 3, 4, # (Hold the “#” key) → [Password] appears Press 1, 2, 3, 4 and press Enter → Network Settings appears Press 1, 2, 3, 4, # (Hold the “#”... -
Page 24: Saving Settings
Press Redial/Mute until [save settings] appears on the screen→ press Enter→ Are You Sure? Press Enter for Yes and the AirLive ePhone-1000 will reboot and save the new settings. Press Redial/Mute again for No, to not save settings and return to Keypad settings. -
Page 25: Web Configuration
WEB Configuration As an alternate to Keypad configuration, the AirLive ePhone-1000 series VoIP Phone can also be configured with a web browser. The AirLive ePhone-1000 Web configuration page is accessed by entering an assigned URL, or by pressing the “IP” button from the VoIP Phone keypad to display the IP address. - Page 26 You can enter all the configuration parameters for the AirLive ePhone-1000 on this web page. Each of the parameters and its options are described in the tables that follow. Enter all of the required parameters and select Save/Reboot to complete the configuration.
-
Page 27: Network Parameters
With PPPoE or modem selected in the iptype drop down list, enter the password in this ppp pin field. With Static selected in the iptype drop down list,, enter the IP address of the AirLive local ip ePhone-1000 in this field. -
Page 28: Protocol Parameters
To make point to point calls to another voice gateway: leave this option unchecked and enter the voice gateway’s IP address in the Service Addr. field. To make calls by dialing IP addresses of other AirLive ePhone-1000 or H.323 devices (such as Netmeeting) in the same network segment, leave this option unchecked and leave the Service Addr. - Page 29 STUN helps the SIP traverse the NAT and locates a public IP address and the type of NAT service for the AirLive ePhone-1000. If this option is selected, enter the IP address of the STUN server in the nat addr field.
- Page 30 If MGCP or SIP protocol is used, there is no specific request for this port. You can enter any number. ※If many AirLive ePhone-1000s are active on the NAT at the same time, each AirLive ePhone-1000 cannot be configured to the same port.
- Page 31 Account Use account authentication to login. Enter the account name and password into the account and pin fields. H.235 account With H.323 protocol used, if the Gatekeeper supports H.235 protocol, please choose this option. Please also fill up the account name and password into the account and pin fields.
-
Page 32: Phone Parameters
Phone Parameter Values Fields Description The use dialplan parameter sets how the AirLive ePhone-1000 dials up., either by a dial plan or by a dial number. The options below set the dial method. disable Select disable to not use either dial plan or dial number. - Page 33 If enable or dialnum is selected, enter a long distance call prefix according to E.164 dddprefix dial rules. For example 00. Enable/disable multi-settings by selecting disable or enable from the dropdown list. 000 You can save a maximum of 5 settings. disable: disables multi-settings, the phone will call out using the current setting.
- Page 34 Audio Parameter Values Fields Description Select the audio type of the phone by selecting an option from the drop down list. audio type The options are g.711u, g.711a, g.723.1, g.729, g.729a, g.729b and auto. Sets the audio frames in the RTP package. If the G723 audio codec used, set it as 1; audio frames If the G729 audio code is used, set it as 2.
-
Page 35: Audio Parameters
Audio Parameters Sets the audio frames in the RTP package. If the G723 audio codec used, set it as audio frames 1; If the G729 audio code is used, set it as 2. If g.723.1 selected in audio type, enable/disable g.723.1 high rate (6.3K) by g.723 high rate checking / unchecking this option. -
Page 36: Other Parameters
Output: Sends operation information, such as register input. to the phone window, debug Output all: Sends all bug information and data to a test window Remote debug: Saves bug information in SDRAM of AirLive ePhone-1000. No check: Disables checks. IP address of the time server here. sntp ip Enables/Disables daylight savings time by checking /unchecking this option. -
Page 37: Save/Reboot Parameters
Save/Reboot Parameters After you enter all the configuration values, press Save/Reboot. AirLive ePhone-1000 will save the settings and reboot. If the webpage returns to the login page, login and configure again. Phone Book Click on Phone Book to access the AirLive ePhone-1000 phone book page. -
Page 38: Registration Message
SIP proxy IP or Domain nat traversal：Select disable Registration Message When the registration for AirLive ePhone-1000 is successful, Ready for Call will appear on the screen. If the registration is not successful hand Log fail or Wait Log will appear. -
Page 39: Using Airlive Ephone-1000
Using AirLive ePhone-1000 To make a phone call When dialing a call with the AirLive ePhone-1000, press “#” after the phone number. Review call record Press the “Miss” button to review any missed calls. Press “#” to return a missed call. Press Vol.+ to view the next entry and Press Vol.- to view the previous entry. -
Page 40: Mute
Mute Press the “Redial/Mute” button during a conversation to mute the microphone. Hold Press “SPD/Hold” button during a conversation to hold a call. - 40 -... -
Page 41: Appendix
＃ ７ ８ ９ ． ０ ：∕@ ；∕－ ’∕＆ Space Switch to upper/lower case H.323 sample web setting When the AirLive ePhone-1000 is operating using H.323 protocol, please change the below parameters. Other settings remain the same. - 41 -... - Page 42 （Contact your service provider for detail information） use service：Please check the box service type：Select common unless specified. service addr： nat tracersal：Select citron unless specified phone number：Enter the phone number provided by the service provider account：Enter your account number provided by the service provider（H.323 ID） pin：Enter pin number provided by the service provider Register port：1719 unless specified.
-
Page 43: Frequently Asked Questions
Check if the RJ-45 cable is connected properly and also confirm to see LCD shows Wait if the AirLive ePhone-1000 has successfully obtained an IP address. Logon or Logon If an IP address is not obtained check to see if there are errors for Failed network and account settings. - Page 44 The AirLive ePhone-1000 Phone Tree Type Menu （administration） - 44 -...
- Page 45 - 45 -...
- Page 46 - 46 -...
Need help?
Do you have a question about the AirLive ePhone-1000 and is the answer not in the manual?
Questions and answers