Emerson 1F95-1291 Installation And Operating Instructions Manual page 7

Screen
SS1 HP1 Press
Reference
key
MS2 HP2
Number
33

34

35 
36 
37

38  
39
 
40
 
41  
42  
43  
44  
45  
46
 
47
 
48  
49  
1. This control can be configured for:
MS2 – Multi-Stage System (2 heat/2 cool)
HP1 – Heat Pump with one stage of compressor (2
heat/1 cool)
HP2 – Heat Pump with two stage compressor or two
compressor system, Gas or Electric backup; (Dual Fuel
see screen reference number 33) (4 heat/2 cool)
SS1 – Single Stage System (3 wire zone see wiring
diagrams.
2. GAS or Electric (ELE) fan operation. If the heating
system requires the thermostat to energize the fan, select
ELE. Select GAS if the heating system energizes the
fan on a call for heat. Note: Resetting the thermostat
switches the option to GAS.
3. O/B Terminal selection – Selects the operation of the
reversing valve (when item 1 is set to HP1 or HP2 only).
When set to "O" the changeover valve will be energized
in COOL to accommodate the majority of heat applica-
tions. If the heat pump requires the changeover valve to
energize in HEAT, select "B".
4. Programs per week – This control can be configured for
7 independent day or 5+1+1 day programming or non-
programmable modes. Default is 7-day mode. The display
indicates "7 Days" as default. Other options "5 Days" or
"0 Days" can be selected. If "0 Days" is selected for non-
programmable mode, the step for EMR will be skipped, as
this feature will not be available in this mode.
5. Program Steps per day – Not available if configured for
non-programmable. This control can be configured for 4
or 2 program steps per day. Default is "4 PS" and can be
toggled between 4 PS and 2 PS.
CONFIGURATION MENU
Displayed
Press or
Factory
to select from
(Default)
listed options
(35) dF -5 - 50
(05) dF 0 - 09
(60) Cd 0-99
(80) AO -5 - 79
(80) bP 79-20
(OFF) Hd On
Humidity 00 -20 LO
(Room Humidity) 20 HI
(OFF) HR LO, HI
(OFF) AH H, C, A
(OFF) CH On
OC (0) od, OFF
(OFF) Change On
UV Lamp
350 Days 25-1975
(OFF) On
Change Pad
100 Hrs 25-1975
OFF On
Change Filter
200 Hrs 25-1975
INSTALLER/CONFIGURATION MENU
Comments
Selects Dual Fuel setpoint (°F), dF selected On with outdoor sen-
sor available.
Selects Dual Fuel setpoint (°F), dF selected On with no outdoor
sensor.
Selects compressor off delay in seconds, dF selected On
Selects Auxiliary Heat cut out temperature. This item appears
if HP1 or HP2 is selected and outdoor sensor is installed and
enabled.
Selects Blower balance point. Selection of 80 disables this feature.
This item appears if HP1 or HP2 is selected and outdoor sensor is
installed and enabled.
Selects Humidity Display alternate with time.
Selects Humidity Display adjustment.
Selects Auto Humidity reduction.
Selects Automatic Humidification.
Selects Cycle Humidifier.
Selects Optimum Comfort or Optimum Dehumidification or Off.
Selects Change UV Lamp feature.
Change UV Lamp duration days.
Selects Change Humidifier Pad feature.
Change Humidifier Pad duration hours.
Selects Change Filter feature.
Change Filter duration hours.
6. System Switch Configuration (MS2/SS1) – This ther-
mostat is configured for Heat and Cool with Auto change-
over default (Cool-Off-Heat-Auto). It can be configured as
Heat & Cool (Cool-Off-Heat), or Heat Only (Off-Heat), or
Cool Only (Cool-Off).
When the control is in heat pump configuration (HP1/
HP2), the system switch configuration will have an
additional mode, Em for Emergency.
7. Energy Management Recovery (EMR) – (this step is
skipped if configured as non-programmable). When set
to "On" causes the thermostat to start heating or cooling
early to make the building temperature reach the program
setpoint at the time you specify.
Example: The heating program is 65°F at night and 70°
at 7 AM. If the building temperature is 65°F, the difference
is 5°F. Allowing 5 minutes per °F rise, the thermostat set-
point will change to 70° at 6:35 AM. Cooling allows more
time per °F, because it takes longer to reach temperature.
8, 9 & 10. Cycle Rate Selection – The factory default setting
is fast cycle (FA Cr) in all modes (Heat, Cool, Em). To
change to slow cycling (SL, Cr), press touch keys
toggle between FA & SL. The cycle rates are below:
Mode Med
Heat 0.6°F
Cool 1.2°F
Heat Pump 1.2°F
Emer Heat 0.6°F
11. Select Compressor Lockout (CL) – Selecting (CL On)
will cause the thermostat to wait 5 minutes between cool-
ing cycles. This is intended to help protect the compressor
from short cycling. Some of the newer compressors have
Option
Selected
Slow
1.5°F
1.7°F
1.7°F
1.7°F
or
7