Do you have a question about the Trimline 1600.1 and is the answer not in the manual?
Questions and answers
Pat Hobbs
February 3, 2025
Seems like my motor died and I need a replacement for a 3300
1 comments:
Mr. Anderson
February 10, 2025
To find a replacement motor for a Hebb Trimline 1600.1, identify the correct motor part number from the parts list. For the Trimline 1600 model, the drive motor part number is KK-2070, and the elevation motor part number is KK-2129. Contact Hebb Industries using the provided phone numbers (903) 534-3832 or (800) 499-4322, or email service@hebbindinc.com to inquire about availability and ordering.
This answer is automatically generated
Jess
February 10, 2025
Does the 1600.1 model fold up for easier storage?
Summary of Contents for Hebb Trimline 1600.1
Page 1
HEBB Industries, Inc. Manufacturers of Fitness Equipment SERIAL NO:________________________ DATE OF PURCHASE: ______________ Write the serial number in the space above for reference. SERIAL NUMBER DECAL ’ ’ ’ ’ ASSEMBLY • USE • MAINTENANCE WARRANTY • PART ORDERING CAUTION: Exercise of a strenuous nature, as is customarily done on this equipment, should not be undertaken without first consulting a physician.
Please complete the warranty registration card included in this manual, and return it as promptly as possible following the purchase. If you would like to speak to a factory representative (800) 499-4322 or email service@hebbindinc.com call: HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 3
If the power cord is damaged, it must be replaced by a power cord from Hebb Industries, Inc. Please contact your dealer or Hebb Industries, Inc. Position treadmill so that the wall plug is visible and accessible.
(we suggest on the end cap by the rear roller). Snap hex wrench into clip. Refer to maintenance instructions for hex key use. ⁄ ˝ Shoulder Washer YLOCK HEBB Industries, Inc. Manufacturers of Fitness Equipment...
“K” or “M” appears in the speed window. If no “M” or “K” appears in the speed window, use the following procedure: remove the console and manually move the switch on the back of the electronics to “KM” or “MILES”. HEBB Industries, Inc. Manufacturers of Fitness Equipment...
POWER button. 10. To stop the treadmill at any time, press the POWER button or pull out the safety pull pin. CAUTION: THIS WILL STOP THE TREADMILL RATHER ABRUPTLY. HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 7
6. To pause the program, follow step 8 under Manual Mode Operation. 7. To stop the treadmill, follow step 9 or 10 under Manual Mode Operation. HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 8
Press to shut off for power to come on; Please clip also inputs weight. Raises and workout lowers target heart rate during the rope securely to your clothes during workout. heart rate program. HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 9
SPEED or INCLINE buttons. The override will last until the end of the current interval. 4. To pause the program, follow step 10 under Manual Mode Operation. 5. To stop the treadmill, follow step 11 or 12 under Manual Mode Operation. HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 10
5. The target heart rate may be adjusted at any time during the workout, using the incline keys. 6. To pause the program, follow step 10 under Manual Mode Operation. 7. To stop the treadmill, follow step 11 or 12 under Manual Mode Operation. HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 11
• If you are in the miles per hour mode, you will see POWER button. a “bri” in the time section when the safety pull pin Press POWER button again. You are now in is inserted. kilometers per hour. HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 12
Program P8-Hill Jogger Program P8–Hill Jogger Program P3-Advanced Walker Interval Interval Speed Grade Speed Grade Program P4-Mountain Walker Program P4–Mountain Walker Program P9-30 Minute 5K Program P9–30 Minute 5K Interval Interval Speed Grade Speed Grade HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 13
This page intentionally left blank HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 14
Telco, 6-pin Limit Switch Heart Rate Chest Strap Handrail, Right Rubber Grip On/Off Switch Elevation Switch Upright Assy. Knob Rheostat Harness Handrail, Left Assembly Switch Cord Elevation Motor Cover Motor Switch Cord Model 1600 HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 15
Power Supply Rear Cross Tube Flywheel Fan, 4” Motor, Drive Motor Controller or Mount Controller/ Fan, 6” Assy Power Supply Motor, Elevation Motor Pivot Rod Elevation Assy. Wheel Bottom Pan Circuit Breaker Power Cord HEBB Industries, Inc. Manufacturers of Fitness Equipment...
J-Bolt assembly. Nut may need to be tightened 2-3 turns. 4. With motor cover still off treadmill, plug treadmill in and test drive belt for slippage. 5. If tension is adequate, reinstall motor cover. If further adjustments are needed, repeat step #3. HEBB Industries, Inc. Manufacturers of Fitness Equipment...
(800 877-3486 or www.jadfitness.com) or your local specialty fitness dealer. • NAPA 8300 Silicone Spray, available at most NAPA Auto Parts stores. • Pyroil Silicone Spray Lubricant, available at most auto parts stores. HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 19
2. Out of calibration. (Models 2600, (See Operation Guide) 3600, 4600) 2. Recalibrate electronics. (See Calibration Instructions) 11. Treadmill squeaks when walked 1. Pivot points need lubrication. 1. Lubricate pivot points. HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Page 20
The belt will somewhat slow down. Use the SPEED UP and SPEED DOWN buttons to set the actual speed displayed in the SPEED window with the desired speed in the CALORIES window. When the two speeds are equal, press POWER. The calibration is complete. HEBB Industries, Inc. Manufacturers of Fitness Equipment...
Need help?
Do you have a question about the Trimline 1600.1 and is the answer not in the manual?
Questions and answers
Seems like my motor died and I need a replacement for a 3300
To find a replacement motor for a Hebb Trimline 1600.1, identify the correct motor part number from the parts list. For the Trimline 1600 model, the drive motor part number is KK-2070, and the elevation motor part number is KK-2129. Contact Hebb Industries using the provided phone numbers (903) 534-3832 or (800) 499-4322, or email service@hebbindinc.com to inquire about availability and ordering.
This answer is automatically generated
Does the 1600.1 model fold up for easier storage?