Fisher & Paykel E522BRXFD2 Installation Instructions page 2

trim installation
8
The bottom trim is designed to cover the front edge of the
floor base panel of the cabinet. This trim can be installed
on a raised toe kick (diagram 1a) or toe kick below the
refrigerator (diagram 1b)
Remembering that if this trim is to be used with the
refrigerator at floor level the cut out dimensions will need
to have 16mm (5/8") added to its height to allow for the
bottom trim to be fitted. Note this trim is optional on this
type of installation. If used with a raised toe kick the 16mm
packer should be part of the base (diagram 5). Therefore
16mm is not required to be added to the height dimension.
1. If used place the 16mm (5/8") piece of plywood or
with bottom trim fitted into the cavity (diagram 5 or 6).
Note the piece should be the same size as the base of
the cavity.
2. Remove protective coating film from surround trim.
3. To install the surrounds, first clip in the top surround.
Ensure the locator strips at the rear of the top brackets clip
into the rear of the top trim.
4. Clip both side trims into place starting from the front
cabinet edge.
kit Part numbers and Cut out dimensions table
10
Refrigerator Model
1 x 635
807
(25") LH
635
1 x 635
807
(25") RH
635
2 x 635
1467
(25")
635 635
1 x 680
852
(26 3/4")
LH
680
1 x 680
852
(26 3/4")
RH
680
2 x 680
1557
(26 3/4")
680 680
16mm (5/8 inch)
plywood or MDF
board insert
Part of base
Diagram 5
Kit Part Numbers Cut Out Dimensions
Plus
Brushed Iridium Width Depth
Joiner
Stainless Stainless A B*
Kit
821351 821361 807mm 700mm
31 13⁄16"
27 9/16"
821352 821362 807mm 700mm
31 13⁄16"
27 9/16"
821353 821363 819264 1467mm 700mm
57 3/4" 27 9/16"
821354 821364 852mm 700mm
33 9⁄16"
27 9/16"
821355 821365 852mm 700mm
33 9⁄16"
27 9/16"
821356 821366 819264 1557mm 700mm
61 5/16" 27 9/16"
moVe into CaVity
9
If installing two refrigerators/
freezers side by side a joiner
kit is required. Refer to these
instructions and fit joiner kit
before pushing refrigerator into
place, see diagram 6.
Plug refrigerator into electrical
socket, run water connection
to refrigerator if required
(Ice & Water models only).
Gently install refrigerator into
cabinetry making sure it is
centred within the surround trim.
The front of the refrigerator
door should be flush with the
front of the cabinetry to obtain
an integrated look.
Ensure the front leveling feet are
adjusted to take the load of the
fridge and keep it in place.
Refrigerator Model
Height
C**
1790mm 1 x 790
962
(31 1/8")
70 1/2"
LH
790
1790mm 1 x 790
962
(31 1/8")
70 1/2"
RH
790
1790mm
2 x 790
1777
(31 1/8")
70 1/2"
790
1790mm
1 x 900
1072
(35 7/16")
70 1/2"
900
1790mm 1 x 790
962
(31 1/8")
70 1/2"
790
1790mm
* Depth is a minimum requirement
70 1/2"
**Height is without 16mm MDF packer
***For refrigerators / freezers where the hinge is not concealed
by the door refer to spare parts for the correct kit number.
820413 D should list non concealed number kit.
Before you call for service or assistance ...
Check the things you can do yourself. Refer to the installation instructions, your User Guide – in particular
the troubleshooting section and check that:
1 your product is correctly installed.
you are familiar with its normal operation.
2
If after checking these points you still need assistance or parts, use the link at
www.fisherpaykel.com for regional service providers.
821996 NZ AU GB AE HK SG IE US CA EU CN IN 03.12
Diagram 6
Kit Part Numbers
Plus
Brushed Iridium
Joiner
Stainless Stainless
Kit
821357 821367
821358 821368
821359 821369 819264
790
821360 821370
837315 837316
Concealed Hinge
Optional
Cut Out Dimensions
Width Depth Height
A B* C**
962mm 700mm 1790mm
37 7/8" 27 9/16" 70 1/2"
962mm 700mm 1790mm
37 7/8" 27 9/16" 70 1/2"
1777mm 700mm 1790mm
70" 27 9/16" 70 1/2"
1072mm 700mm 1875mm
42 ¼" 27 9/16" 73 13/16"
962mm 700mm 1790mm
37 7/8" 27 9/16" 70 1/2"
Non Concealed Hinge