Do you have a question about the Brush Master and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for GXi Outdoor Power Brush Master
Page 1
Chipper/Shredder with 2-Way Feed Owner’s Manual This manual contains important safety instructions for Chipper/Shredder models: CH6, CH8 READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS CAREFULLY SAVE THESE INSTRUCTIONS. Do not return this unit to the store! For product questions or service, CALL 1-919-550-3221 or go to www.beastpowerequipment.com When you call the help-line you will need to have the following information: Date of Purchase: _______________________ Location of Purchase: _______________________...
Specifications table pg 2) in the limb chute. Do not deflector has been installed properly. deposit branches larger than 1/4 inches into the leaf funnel. DO NOT force the branches into this machine, allow the machine to automatically feed through. Rev: 4.5/15/12 Brush Master™ Chipper/Shredder with 2-Way Feed ...
This bag contains the owner's manual, assembly hardware, tools, safety glasses and oil fill funnel If you are missing any parts, please complete the form on the next page and fax it to us at: 919-550-3277. Rev: 4.5/15/12 Brush Master™ Chipper/Shredder with 2-Way Feed ...
If emailing, please scan in your proof of purchase. Refer to parts diagram and part list on page 5 and 6 for part numbers. This will expe- dite the process. Rev: 4.5/15/12 Brush Master™ Chipper/Shredder with 2-Way Feed ...
Read them carefully. If a label pants and shirts. Loose fitting clothing or jewelry can comes off or becomes hard to read, contact your GXi be caught in movable parts. Wear leather work gloves Outdoor Power dealer for a replacement.
19. Keep children, bystanders, and pets 75 feet away. wet vegetation, or long 20. Use only manufacturer approved accessories/ branches such as attachments. Weeping Willows as they may clog the cutting chamber. Rev: 4.5/15/12 Brush Master™ Chipper/Shredder with 2-Way Feed ...
45mm long bolts, 26 flat washers, 4 locking washers and 11 nylon locking nuts Bolt Identification: Figure 2 20mm 30mm 45mm Place top of bolt head here Actual Size Rev: 4.5/15/12 Brush Master™ Chipper/Shredder with 2-Way Feed ...
Page 14
Third fasten the components together with the remaining 8 30mm bolts fasten here fasteners. Each bolt should have two flat washers and a nyloc nut. 9. Re-connect the spark plug wire 10. Add oil and fuel. Rev: 4.5/15/12 Brush Master™ Chipper/Shredder with 2-Way Feed ...
Refuel in a well ventilated area with the engine stopped. Fuel vapors are extremely flammable and may ignite after the engine has started. Make sure that any spilled fuel has been wiped up before starting the engine. Rev: 4.5/15/12 Brush Master™ Chipper/Shredder with 2-Way Feed ...
To accomplish this, remove the handle. Let the rope rewind slowly. Repeat the previous discharge chute and the flail screen out of the discharge steps until engine fires. chute. Rev: 4.5/15/12 Brush Master™ Chipper/Shredder with 2-Way Feed ...
The governor controls the discharge chute and the flail screen out of the discharge maximum safe operating speed of the engine. chute. 5. Maintain or replace safety and instruction labels, as necessary. Rev: 4.5/15/12 Brush Master™ Chipper/Shredder with 2-Way Feed ...
Removing and Sharpening the Limb Chute Blades The chipper was shipped with two blades attached spare blades are sold in sets from GXi (Part Number LCSSP11-018) 1. Disconnect the spark plug wire and ground against the engine.
Page 19
Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc. Rev: 4.5/15/12 Brush Master™ Chipper/Shredder with 2-Way Feed ...
Call GXi Parts & Service (919)-550-3221 NOTE: For repairs beyond the minor adjustments listed above, contact GXi Parts and Service (919)-550-3221 for support over the phone or getting setup with your nearest authorized service dealer. Rev: 4.5/15/12 Brush Master™...
To Qualify for this Warranty: The product must be purchased in the United States from a dealer authorized by GXi Outdoor Power, LLC to sell the product. This warranty applies to first retail purchaser/owner during the applicable warranty time period. No warranty registration is necessary to obtain warranty on BRUSH MASTER products.
Need help?
Do you have a question about the Brush Master and is the answer not in the manual?
Questions and answers