Advertisement
Quick Links
Advertisement
Related Manuals for Laney Richter R1
Summary of Contents for Laney Richter R1
- Page 1 Laney Richter Bass Amplification R3/R3H R4/R4H User manual...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following. Read all safety and operating instructions before using this product All safety and operating instructions should be retained for future reference Obey all cautions in the Operating instructions and on the back of the unit All operating instructions should be followed This product should not be used near water, i.e.
- Page 3 INTRODUCTION Congratulations on your decision to purchase a Laney amplifier. Laney products are designed with ease of operation as a primary objective, however to ensure you derive the best from your new amplifier, it is important you take time to read this user manual and to familiarise yourself with the control functions and facilities available.
- Page 4 Laney R1 front ASS MPLIFIER QUALISATION ORMAL CTIVE CTIVE OWER REQUENCY EVEL D.I. NPUTS NHANCE REBLE OLUME OWER R1 Rear T2A L T2A L 115V 115V ARNING O REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE...
- Page 5 Laney Laney Selects the MID-frequencies to be cut or boosted in 6.Paramid frq: conjunction with the PARAMID GAIN control (7). To access LO mid-frequencies turn the FREQUENCY control anticlockwise, to access HI mid frequencies turn the FREQUENCY control clockwise. Sets the level of boost or cut applied to the frequency set 7.Paramid Level:...
- Page 6 Laney This control is used to set the level of gain present in the 2.Gain: pre-amp. The higher the level of gain, the more the signal will clip producing distortion. The GAIN control should be used in conjunction with the VOLUME control (10) to produce the desired signal characteristics.
- Page 7 Laney Laney 14.Ext Speaker This socket should be used to connect an extension-cabinet. socket: The impedance of the extension-cabinet must not be less than 8 Ohms. Connecting cabinets that have a lower impedance than 8 Ohms will result in the amplifier overheating .
- Page 8 Laney Laney The ENHANCE control provides an increased definition at the 4.Enhance: low-end of the frequency spectrum giving you a tighter, punchier sound. The ENHANCE control does this by providing a dip in the frequency-response of the amplifier at approximately 200hz.
- Page 9 Laney Laney 15.Ext Speaker This socket(s) should be used to connect an extension- socket: cabinet. The impedance of the extension-cabinet must not be less thean 8 Ohmsfor the R3, or for the R3H a Minimum 4 Ohms. Connecting cabinets that have a lower impedance than 8 Ohms will result in the amplifier overheating.
- Page 10 Laney Laney 1.Inputs: Normal and High inputs are provided for connection of bass guitars. High output basses, either Active or Passive should be connected via the High socket. Low output basses should be connected using the normal input. High output basses may also be placed in the Normal input if pre-amp overloading is desired.
- Page 11 Laney Laney R5 Front ASS MPLIFIER QUALISATION ORMAL IMITER REQUENCY REQUENCY CTIVE EVEL EVEL CTIVE CTIVE OWER D.I. NPUTS NHANCE O ARA I ARA REBLE OLUME OWER R5 Rear T6.3A L T6.3A L 115V 115V AUTION O REDUCE THE RISK OF ELECTRIC SHOCK DO NOT ERIAL UMBER T3.15A L...
- Page 12 Laney Laney Selects the LO MID-frequencies to be cut or boosted in 6. Lo Paramid frq: conjunction with the LO PARAMID LEVEL control (7). To access low LO mid-frequencies turn the FREQUENCY control anticlockwise, to access higher LO MID frequencies turn the FREQUENCY control clockwise 7.Lo Paramid Level:...
- Page 13 Laney Laney Power Output 120W 165W 165W 300W 300W 300W Maximum Power Consumption 120W 240W 300W 300W 450W 450W 450W 50/60Hz Input Impedance Normal/Hi 1M Ohm 1M Ohm 1M Ohm 1M Ohm 1M Ohm 1M Ohm 1M Ohm Input Sensitivity Norma/Hi...
- Page 16 Laney Amplification Newlyn Road, Cradley Heath, West Midlands B64 6BE United Kingdom. WWW.laney.co.uk...