Monitor Send Section; Aux Master Section; Modifications; Mon/Aux Sends > Post-Eq - Behringer Xenyx XL1600 User Manual

XENYX XL1600/XL2400/XL3200
SOLO
Press the SOLO switch to listen in on the effect signal on the head-
phones/speakers as well as see it on the monitor meter 1/2. The
corresponding LED lights up when the solo function is activated.
FX RETURN
The FX return fader adjusts the volume level of the returned effect
signal in the main mix and subgroups (this depends on the routing
switch you have pressed).
5.8

Monitor send section

The monitor send section merges the
monitor signals of all channels. Then the
mix is sent to the monitor outputs. The
monitor fader provides precise adjust-
ment and optical control of the monitor
output signals.
SEND
The SEND faders control the output level
of the monitor buses. Each fader is 60 mm
long and features 10 dB headroom.
MUTE
Each monitor send has a MUTE switch
and MUTE LED.
SOLO
For acoustic control of the stage sound,
use the SOLO switch to feed the monitor
signal to the headphone and speaker out-
put. If you connect the speaker output to
a monitor that is identical with the monitor
speakers on stage, you can tell how the
stage sound is perceived.
5.9

AUX master section

This section is split up in an aux send section (left side) and an
aux return section (right side). The aux send paths 1 and 2 can
individually be switched from pre-fader to post-fader depending on
whether you want to use them as monitor or effect signal paths. As
with all outputs, both aux master outputs feature 10 dB headroom
as well as a MUTE and SOLO switch.
In the aux return section, you can adjust the signals of the de-
vices (CD player, effects unit, submixer, etc.) connected to the aux
inputs which are then routed to the monitor buses and the main
mix.
PRE/POST
This
i s t h e
global
PRE/
POST
switch
for the
aux
buses.
For utmost flexibility, each AUX bus can individually be switched
from pre-fader to post-fader.
AUX SEND
The Master AUX SEND controls 1 and 2 adjust the signals' volume
level of the respective aux send connector. This way you adjust the
sum of the AUX 1 and AUX 2 signals on the input channels.
MUTE
The MUTE switch mutes the aux outputs.
SOLO
The aux send signals can individually be listened to using the
SOLO function.
14
MON
A signal sent from AUX RETURN can be added to the stage mix
using the MON control.
AUX RETURN
The AUX RETURN controls adjust the volume level of the aux
return signals in the main mix.
6.

Modifications

+ These modifications require soldering. Attempt only if
you are experienced in using an iron on PCBs. Other-
wise, refer to qualified personnel. After modification the
warranty becomes void.
We wish to be absolutely clear that BEHRINGER cannot
+
be held responsible after you start disassembling your
XENYX. If you make much of your warranty privileges,
think again.
Links should not be threaded into the holes on the PCB,
+
but are to be soldered to the tinned areas around the
holes. Bend the links a little upwards.
6.1 Mon/Aux sends > post-EQ
Pre-fader switched monitor sends and aux sends are tapped off
before the equalizer. Do you prefer post-EQ? What are you wait-
ing for? You don't have to look far—the necessary information is
found on the bottom side of the unit.
Make sure to turn off the mixer and disconnect it from
+
the mains before removing the cover.
1) Strip the PRE EQ lead.
2) Solder a POST EQ link into place.
3) Make these modifications to as many channels as required
(does it have to be all of them?).
6.2 Direct Out > pre-fader
If you prefer to use the Direct Out pre-fader than post-fader, the
signal needs to be tapped off before the fader and not after the
fader. To perform this modification, find the label "DIR-OUT" on
the circuit board.
Make sure to turn off the mixer and disconnect it from
+
the mains before removing the cover.
1) Strip the POST FADER lead.
2) Solder a PRE FADER link into place.
3) Make these modifications to as many channels as required.
Modifications