92646_Guide:92646_Guide 4/27/10 10:01 AM Page 1 IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS Owner’s Use and Care Guide for Owner’s Use and Care Guide for Whirlpool Baths Hydromassage Baths With with Installation Instructions Installation Instructions SAVE THESE INSTRUCTIONS...
92646_Guide:92646_Guide 4/27/10 10:01 AM Page 2 INTRODUCTION Thank You for choosing us. The perfect tub for your remodeling and building needs. Before Using Before using your Hydromassage Bath Tub, please read the IMPORTANT Before using your Whirlpool Bath Tub, please read the IMPORTANT OPERATING, SAFETY, MAINTENANCE, and INSTALLATION INSTRUCTIONS OPERATING, SAFETY, MAINTENANCE, and INSTALLATION in this manual.
The water temperature in the whirlpool bath should not exceed 104 degrees F (40 deg C). Hot whirlpool baths can put certain stresses on the body, as does degrees F (40 deg C). Hot hydromassage baths can put certain stresses on the any hot bath or shower.
92646_Guide:92646_Guide 4/27/10 10:01 AM Page 4 INSTALLATION INSTRUCTIONS ATTENTION INSTALLER: PLEASE READ THE FOLLOWING IMPORTANT CONSIDERATIONS! READ ALL INSTRUCTIONS CAREFULLY AND FOLLOW ALL LOCAL PLUMBING AND ELECTRICAL CODES. 1. Before installation, make sure proper access is made to the final connections. 2.
92646_Guide:92646_Guide 4/27/10 10:01 AM Page 6 FRAMING SUNKEN UNITS 1. Construct a framing pocket which allows for the insertion of your particular model. (Check all dimensions against the unit to be installed.) For pump access. A 17” high by 27” wide minimum opening is needed to the integral pump. Then install the supply and drain piping and connecting fittings for the unit.
92646_Guide:92646_Guide 4/27/10 10:01 AM Page 7 ELECTRICAL CONNECTIONS WARNING – When using electrical products, basic precautions should always be followed, including the following: A licensed electrician should make all service connections. 1. DANGER RISK OF ELECTRIC SHOCK. Connect only to a circuit protected by a ground-fault circuit-interrupter.
92646_Guide:92646_Guide 4/27/10 10:01 AM Page 8 OPERATING INSTRUCTIONS CAUTION: READ IMPORTANT SAFETY INSTRUCTIONS FIRST. ˚ 1. Fill unit with a water level of 2” to 3” (5 to 7.5 cm) above the highest jets (100 or less recommended). NOTE: Failure to fill water to proper level before operating your unit may damage the pump and void the warranty.
92646_Guide:92646_Guide 4/27/10 10:01 AM Page 9 CARE AND CLEANING Units are easy to keep clean and sparkling. Simply use warm water and a leading liquid cleaner. Never use abrasives as this will dull the surface of the unit or leave scratches.
LIMITED WARRANTY 92646_Guide:92646_Guide 4/27/10 10:01 AM Page 10 92646_Guide:92646_Guide 4/27/10 10:01 AM Page 10 The Manufacturer warrants to the original retail purchaser (herein “Original purchaser”) that the unit (herein “the unit”) to which this warranty is affixed is free from hidden defects in materials and workmanship under normal use and service for (3) LIMITED WARRANTY LIMITED WARRANTY...
92646_Guide:92646_Guide 4/27/10 10:01 AM Page 11 TROUBLESHOOTING GUIDE WARNING–This guide is meant for a general aid only. All electrical problems should be corrected by a qualified electrician or authorized service representative. For warranty service contact your dealer, wholesale WARNING–This guide is meant for a general aid only. All electrical distributor or write: problems should be corrected by a qualified electrician or authorized ATTN: Consumer Affairs...
Page 11
92646_Guide:92646_Guide 4/27/10 10:01 AM Page 12 The manufacturer represents that the product to which this label is affixed (a) duplicates samples independently tested by NAHB Research Center, and certified to conform to the requirements of HUD UM Bulletin No. 73a and the appropriate ANSI Z124 standard and (b) has been manufactured under quality controls deemed appropriate by the manufacturer and periodically...