Important Safety Instructions; Removal Of Old Unit - Waste King FOOD WASTE DISPOSER Owner's Manual

IMPORTANT SAFETY INSTRUCTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO
PERSONS. SAVE THESE INSTRUCTIONS.
WARNING – When using electrical appliances, basic
precautions should always be followed, including the
following:
1. Read all instructions before using the appliance.
2. To reduce the risk of injury, close supervision is
necessary when an appliance is used near chil-
dren.
3. Do not put fingers or hands into a waste disposer.
4. Turn the power switch to the off position before
attempting to clear a jam or remove an object
from the disposer.
5. When attempting to loosen a jam in a waste dis-
poser, use a long wooden object such as a wooden
spoon or the wooden handle of a broom or mop.
6. When attempting to remove objects from a waste
disposer use long-handled tongs or pliers. If the

1. REMOVAL OF OLD UNIT

TYPICAL INSTRUCTIONS, YOUR MODEL MAY VARY.
Before starting this step, turn off electrical power at
the circuit breaker or fuse box.
If your old mount is the same as the mount on your
new disposer, just reverse the assembly instructions
found in section 3. If your new mount system is differ-
ent, follow these instructions:
A. Use a pipe wrench to disconnect drain line where
it attaches to disposer discharge tube (see 1A).
B. Remove disposer from sink flange by turning
mount ring to the left clockwise (see 1B). If you
are unable to turn the mount ring, tap on one of
the extensions from the ring with a hammer.
Some mounting systems have tubular extensions.
Inserting a screwdriver into one tube will provide
additional leverage for turning the mount ring
(see 1B). Some disposers may require the removal
or loosening of nuts from the mount screws (see
1C). Some disposers may require the removal of a
clamp.
Caution: Be sure to support the disposer
while performing this step or it may fall
when the mounting ring is disconnected
from the mounting assembly. If your dis-
poser is hard wired (metal shielded cable
not utilizing a wall plug), complete
steps C and D. If you utilize a plug-
in cord, go on to step E.
C. When disposer is removed, turn up side
down and remove electrical cover plate
(see 1D).
D. Use screwdriver to remove green ground
wire. Remove wire nuts from black and
disposer is magnetically actuated, non-magnetic
tools should be used.
7. To reduce the risk of injury by materials that may
be expelled by a waste disposer, do not put the
following into a disposer: clam or oyster shells;
caustic drain cleaners or similar products; glass,
china or plastic; large whole bones; metal, such as
bottle caps, tin cans, aluminum foil or utensils;
hot grease or other hot liquids; whole cornhusks.
8. When not operating a disposer, leave the stopper
in place to reduce the risk of objects falling into
the disposer.
9. DO NOT operate disposer unless splash guard is
in place. (Does not apply to the Top
Control/Batch Feed units.)
10. For proper grounding instructions see the ELEC-
TRICAL CONNECTION portion of this manual.
white power wires and separate disposer wires
from power cable wires. Loosen screws on cable
clamp and separate cable from disposer.
E. To remove remaining mount system from the
sink, loosen mount screws, push mount ring up.
Under it is the snap ring. Use screwdriver to pop
off ring (see 1E). Remove mount ring, protector
ring and gasket from sink flange. Some mounts
will require the unscrewing of a large ring holding
the sink flange in place. Pull sink flange up
through sink and clean off old putty from sink.
IMPORTANT: Unless you have a new
home, this is a good time to clean out the
trap and drain lines by running a drain
auger or plumber's snake before installing
your new disposer.
1C
1A
1D
1B
1E