Integra RC-550M User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Using the RC-550M Remote Controller

You can use the RC-550M remote controller to control

your other AV components, including those made by

other manufacturers. To do this you can:

• Enter a remote control code for the component that

you want to control (e.g., DVD, TV, VCR).

• Learn commands directly from the other component's

remote controller (see page 6).

• Use the Macro function to learn a sequence of actions

(see page 7).

• You can also edit the remote controller modes (see

page 9).

Entering a Remote Control Code

By entering the appropriate remote control code for each

of your components, you can control each component by

selecting the relevant remote controller mode: DVD, TV,

VCR, CBL (cable), or SAT (satellite).

Look up the appropriate remote

control code for the component.

See "Remote Control Codes" on

page 2

Press and hold down the [Cus-

tom] button for more than three

seconds.

The remote controller enters Custom

mode.

Roll the scroll wheel to select

"PRGRM," and then press the

scroll wheel.

Roll the scroll wheel to select the

the remote controller mode you

want to use with the component,

and then press the scroll wheel.

The following remote controller modes

can be selected: DVD, TV, VCR, CBL,

or SAT.

Use the number buttons to enter

the 4-digit remote control code.

If the code is accepted, the following

appears on the display for awhile, and

then the normal display reappears.

If the code is not accepted, after the

message "RETRY" has been displayed,

the code entry display reappears, and

you should try entering the code again.

To cancel this procedure at any point,

press the [Custom] button.

Select the remote controller

mode, point the remote control-

ler at the component, and check

its operation.

Remote Control Codes for an Integra/

Onkyo DVD Player

The remote control code that you use with an Integra/

Onkyo DVD player depends on whether it's connected

via

, as follows:

5001: Use this code if you've connected an

and an RCA/phono analog audio cable to your

DVD player. This is the default setting, so if

you're using

Point the remote controller at the DTR-8.4 to

operate the DVD player.

5002: Use this code if your DVD player doesn't have

socket, or you're not using

the remote controller at the DVD player to

operate it.

cable

, you don't need to change it.

. Point

Table of Contents

Need help?

Do you have a question about the RC-550M and is the answer not in the manual?

Questions and answers

Summary of Contents for Integra RC-550M

Page 1: Entering A Remote Control Code
Using the RC-550M Remote Controller You can use the RC-550M remote controller to control Use the number buttons to enter your other AV components, including those made by the 4-digit remote control code. other manufacturers. To do this you can: •...
Page 2: Remote Control Codes
Using the RC-550M Remote Control —Continued Remote Control Codes CBL (cable receiver) Manufacturer Control code Manufacturer Control code When two or more codes are given, Magnavox 3014 2005, 2006, 2007, 2009 try each one in turn, and choose the Memorex...
Page 3 Using the RC-550M Remote Controller —Continued Manufacturer Control code Manufacturer Control code Akai 1002 1003, 1004, 1007, 1008, Philips 1014, 1018 Amtron 1009 Pioneer 1004, 1006 Anam National 1003, 1009 Portland 1004, 1005, 1006 1004, 1005, 1006 Prism 1012 Audiovox...
Page 4: Controlling A Satellite Receiver
] Select menu items Stop [Enter] Conﬁrm selection Rewind Number buttons Enter numbers Fast forward The following buttons control the Integra AV receiver. Pause Rec [ Record [VOL] Adjust the receiver volume [Muting] Mute the receiver The following buttons control the Integra AV receiver.
Page 5: Controlling A Cable Receiver
Select cable channels TV CH [+]/[–] Select TV channels Number buttons Enter numbers Number buttons Enter numbers The following buttons control the Integra AV receiver. [CH/Disc] Select cable channels [TV Input] Select TV or VCR input [VOL] Adjust the receiver volume...
Page 6: Learning Commands From Another Remote Controller
[Zone 2], and the scroll wheel button. want to teach a new command, • The RC-550M remote controller can learn a total of and then press the scroll wheel. 150 commands. However, the commands of some...
Page 7: Using Macros
Using the RC-550M Remote Controller —Continued Using Macros Roll the scroll wheel to select a macro, and then press the scroll With the Macro function you can program the remote wheel. controller to perform a sequence of actions with one Macros are numbered from 1 to 8.
Page 8: Running Macros
Using the RC-550M Remote Controller —Continued Running Macros Programmed macros can be run as follows. Press the [Macro] button. Macro #1 selected Roll the scroll wheel to select the macro’s number, and then press 1st character the scroll wheel. The actions in the macro are performed...
Page 9: Editing Remote Controller Modes
Using the RC-550M Remote Controller —Continued Reordering the Remote Controller Modes Editing Remote Controller Modes You can change the order in which the remote controller Adding New Remote Controller Modes modes appears when you roll the scroll wheel. The posi- tion of the AMP mode cannot be changed.
Page 10: Deleting Remote Controller Modes
Using the RC-550M Remote Controller —Continued Deleting Remote Controller Modes Assigning Remote Controller Modes You can delete remote controller modes that you don’t With this function you can assign a remote controller need, such as modes for components that you don’t have.
Page 11: Changing The Remote Controller's Transmission Signal Format (Ir/Rf)
The default setting is IR. cessfully, “OK” appears on the display. This is useful when, for example, the Integra receiver is installed in a rack or is not in line of sight of the remote controller as it allows you to use a commercially avail-...