Advertisement
Deleting Data
Delete data in the Recall Mode. The actual procedure you should use to
delete data depends on the type of data it is.
To delete auto memory data
The following procedure deletes an entire set (from start measurement to end
measurement) of auto memory data.
Important!
Auto memory
You cannot delete data while an auto memory
measurement indicator
measurement is in progress ("AUTO" flashing
on the display).
A
B
AUTO
1. In the Recall Mode, display the start data
RECALL
C
m
2. To clear the data, hold down A until the
A
C
D
( Auto Memory Start Display )
To delete manual memory, maximum, and minimum data
1. In the Recall Mode, display the data that you want to delete.
2. To clear the data, hold down A until the watch emits a beep (and until
"CLR" stops flashing on the display).
ERROR WARNING FUNCTION
This watch is designed to automatically stop taking measurements when
there is a sensor malfunction, when battery power drops below a certain
level, or when battery voltage is decreased below a certain level due to very
cold temperatures.
Sensor malfunction
During Barometric Pressure
Measurement
C
hPa mb
P
ERROR
ERROR
Low battery
During Barometric Pressure
Measurement
C
hPa mb
P
BATTERY
BATTERY
Important!
If the sensor is malfunctioning when it comes time for an barometric
pressure measurement to be taken, the barometric pressure value appears
as "– – – –" on the display and the corresponding point on the barometric
pressure graph is left blank.
There may be cases where the "ERROR" or "BATTERY" message is
cleared once you change modes. In this case, you can continue using the
watch normally unless the error warning message reappears.
Whenever there is a sensor malfunction, be sure to take the watch to an
authorized CASIO distributor or Service Center as soon as possible. If the
appearance of the "BATTERY" message is caused by extremely low
temperature, the message should clear from the display when normal
temperature returns. It is recommended, however, that you still have the
watch checked by an authorized CASIO distributor or Service Center.
of the set of auto memory data that you
want to delete.
watch emits a beep (and until "CLR" stops
flashing on the display).
During Altitude Measurement
AUTO
ALTI
C
m
P
ERROR
During Altitude Measurement
AUTO
ALTI
C
m
P
BATTERY
ALARM FUNCTIONS
Mode indicator
When the Daily Alarm is on, the alarm sounds
Alarm on
for 20 seconds at the preset time each day.
indicator
Press any button to stop the alarm after it
starts to sound.
A
B
When the Hourly Time Signal is on, the watch
beeps every hour on the hour.
A
C
D
Hourly time signal
Hour
on indicator
Minutes
To set the alarm time
1. Use C to enter the Alarm Mode.
2. Hold down A until the hour digits flash on the display. The hour digits
flash because they are selected .
• At this time, the alarm is automatically switched on.
3. Press C to change the selection in the following sequence.
Hour
4. Press D to increase the selected digits. Holding down D changes the
selection at high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you
select for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the
time correctly as morning (A) or afternoon (P).
5. After you set the alarm, press A to return to the Alarm Mode.
To switch the Daily Alarm and Hourly Time Signal on and off
Press D while in the Alarm Mode to change the status of the Daily Alarm and
Hourly Time Signal in the following sequence.
[Alarm ON Indicator / Hourly Time Signal ON Indicator]
Both OFF
Both ON
To test the alarm
Hold down D while in the Alarm Mode to sound the alarm.
STOPWATCH FUNCTIONS
Mode indicator
The Stopwatch Functions let you record
elapsed time, split times, and two finishes.
A
B
The range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
Stopwatch functions are available in the Stop-
watch Mode, which you can enter using C.
C
D
1/100 second
Hours
Seconds
Minutes
(a) Elapsed time measurement
D
D
D
Start
Stop
Re-start
(b) Split time measurement
B
D
B
Start
Split
Split release
(c) Split time and 1st-2nd place times
D
B
D
Start
Split
Stop
First runner
Second runner finishes.
finishes.
Record time of first runner.
1675-6
Minutes
Hourly Time
Daily Alarm only
Signal only
D
B
Stop
Clear
D
B
Stop
Clear
B
B
Split release
Clear
Record time of
second runner.
Advertisement
