REVELL P-51D Mustang Assembly Manual

REVELL P-51D Mustang Assembly Manual

P-51d mustang
Hide thumbs Also See for P-51D Mustang:

Advertisement

Quick Links

North American Aviation created the
P-51D Mustang in response to a British
requirement in 1940. Originally powered
by an Allison V-1710 engine, then later
by a Rolls Royce Merlin engine which
greatly increased performance at high
altitudes. Additional improvements that
appeared on the P-51D included a
bubble canopy on a cut down fuselage
spine, and six .50 caliber machine guns.
The P-51D was the final Mustang variant
to see combat during World War II, and
it was considered to be one of the most
successful fighters of that era.
There are two sets of markings provided
with this kit of the P-51D. One is the
Beautiful Doll flown by Lt. Col. John
D. Landers awhile he was assigned to
the 84th Fighter Squadron. The second
aircraft, Miss Marilyn II, was assigned to
the 343rd Fighter Squadron. It was flown
by 1st Lt. Robert Welch.
* REPEAT SEVERAL TIMES
REPEAT PROCEDURE
*
` `
* A REPETER PLUSIEURS FOIS
* REPETEZ LE PROCEDE
REaD tHIs BEFORE YOu BEgIn
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (H) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before cementing
in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECaL appLICatIOn InstRuCtIOns
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
nOtE: Decals are compatible with setting
solutions or solvents.
If you have any questions or comments, call our hotline at:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85524110200), part number, description, your return address and phone number.
KIT 5241
p-51D Mustang
* DECAL
* OPTIONAL PARTS
`
`
* DECAL COMANIE
* PIECES EN OPTION
LIRE CE QuI suIt aVant DE COMMEnCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (H) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente
peu concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECtIVEs D'appLICatIOn DEs autOCOLLants
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son support
en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMaRQuE: Les autocollants sont compatibles avec les
solutions de fixage ou les solvants.
or, please write to:
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
* CEMENT TOGETHER
* ASSEMBLY CAUTION
`
`
* A COLLER
*ATTENTION D ASSEMBLEE
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
this paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Aluminum
Aluminium
Brass
Laiton
Brown
Brun
Chromate Green
Vert chromate
Chromate Yellow
Jaune chromate
Flat Black
Noir mat
Flesh
Chair
Gray
Gris
Vert
Green
Khaki
Ocre
Olive Drab
Gris olivet
Red
Rouge
Silver
Argent
Steel
Acier
Yellow
Jaune
White
Blanc
(800) 833-3570
85524110200
* DO NOT CEMENT
* NE PAS COLLER

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the P-51D Mustang and is the answer not in the manual?

Questions and answers

Summary of Contents for REVELL P-51D Mustang

  • Page 1 If you have any questions or comments, call our hotline at: or, please write to: Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007 Be sure to include the plan number (85524110200), part number, description, your return address and phone number.
  • Page 2: Cockpit Assembly

    COCkpIt assEMBLY COMPLETED ASSEMBLY INSTRUMENT PANEL RADIO GEAR SEAT FLAT BLACk wITh whITE INSTRUMENT DETAILS AND ChROMATE GREEN ChROMATE GREEN (whITE BELTS wITh SILVER BUCkLES) SILVER SwITChES FLAT BLACk CONTROL COLUMN FLAT BLACk ChROMATE GREEN OLIVE DRAB COCKPIT FLOOR ChROMATE GREEN PILOT'S ARMOR (PAINT ShADED AREA BROwN) FLAT BLACk...
  • Page 3 FusELagE assEMBLY COntInuED LEFT FUSELAGE PAINT ShADED AREA ChROMATE GREEN (PAINT DETAILS FLAT BLACk) ChROMATE yELLOw LEFT SHROUDED ExHAUST STEEL LEFT UNSHROUDED TAIL WHEEL ExHAUST STEEL STEEL (FLAT BLACk TIRE) HOT AIR ExHAUST RAMP ChROMATE yELLOw INTERIOR ChROMATE yELLOw Kit 5241 - Page 3...
  • Page 4: Wing Assembly

    wIng assEMBLY TOP DOOR CUT OFF AND CUT TOP DOOR OFF IF PLACED ON TOP OF THE WING IT IS TO BE DISPLAYED IN THE OPEN POSITION. GUN BAY DOOR PLACE IT ANYWHERE ON (OPEN POSITION) THE TOP OF THE WING. GLUE OTHER TWO DOORS IN THE OPEN POSITION ALONG THE LEADING...
  • Page 5: Landing Gear Assembly

    LanDIng gEaR assEMBLY RIGHT LANDING GEAR OUTER RIGHT MAIN GEAR DOOR RIGHT INNER GEAR DOOR ChROMATE yELLOw INTERIOR TIRE FLAT BLACk WHEEL HUB STEEL RIGHT MAIN GEAR STRUT STEEL PAINT INTERIOR OF whEEL (PAINT ShADED AREA SILVER) wELLS ChROMATE yELLOw LEFT LANDING GEAR LEFT INNER GEAR DOOR ChROMATE yELLOw INTERIOR...
  • Page 6: Airframe Assembly

    aIRFRaME assEMBLY LANDING GEAR DETAILS OMITTED FOR CLARITY PITOT PROBE SILVER LANDING LIGHT SILVER wITh A CLEAR LENS FLAT BLACk RIGHT HORIzONTAL TAIL AIR SCOOP LEFT LOWER ENGINE HORIzONTAL COMPLETED WING COVER TAIL ASSEMBLY pROpELLER assEMBLY COWL PLATE PROPELLER FLAT BLACk wITh yELLOw TIPS SPINNER BACK COMPLETED ASSEMBLY SPINNER FRONT...
  • Page 7 CanOpY anD pILOt assEMBLY CANOPY WINDSCREEN CLEAR CLEAR GUN SIGHT FLAT BLACk CANOPY FRAME PILOT'S TORSO khAkI FLIGhT SUIT wITh OLIVE DRAB hOSES, BROwN GLOVES AND BOOTS, khAkI hELMET wITh BROwN GOGGLES AND PAINT FACE FLESh PILOT'S RIGHT ARM BROwN GLOVES COMMOn DECaL guIDE H(H) F(F)
  • Page 8: Decal Placement

    DECaL pLaCEMEnt AIRCRAFT OF COL JOHN D. LANDERS, 84 FIGHTER SqUADRON, FIGHTER GROUP PAINT RED STRIPE ON COWL ON BOTH SIDES OF THE FUSELAGE ITEMS IN APPLY RED "BIG PARENTHESIS BEAUTIFUL DOLL" "( )" ARE TO FIRST. WHEN DRY BE USED ON APPLY THE BLACK OPPOSITE SIDE ONE ON TOP.

This manual is also suitable for:

5241

Table of Contents

Save PDF