The new Ferrari was shown to the public
for the first time anywhere in the world at
the Detroit Motor Show in January 2004.
The presentation took place just 50 years
after the first Ferrari GT established itself
across the Atlantic. Like its predecessor
the 456M GT and GTA, the 612 Scaglietti
has a front engine located behind the
front axle, which accounts for the striking
length of the car. This position provides
an almost exact equilibrium in the axle
load distribution giving it almost perfect
handling. The Scaglietti takes just 4.4
seconds to accelerate from 0 to 100 and
15.5 seconds to 200 kph, with a top
speed of 321 kph. In the 612 Scaglietti
Ferrari have succeeded in combining high
performance with comfort and at the same
time more sports car than ever before.
* REPEAT SEVERAL TIMES
REPEAT PROCEDURE
*
` `
* A REPETER PLUSIEURS FOIS
* REPETEZ LE PROCEDE
read THis BeFOre YOU Begin
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (H) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before cementing
in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
decal applicaTiOn insTrUcTiOns
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
nOTe: decals are compatible with setting
solutions or solvents.
If you have any questions or comments, call our hotline at:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85289610200), part number, description, your return address and phone number.
KIT 2896
Ferrari 612 scaglieTTi
* OPTIONAL PARTS
* DECAL
`
`
* DECAL COMANIE
* PIECES EN OPTION
lire ce QUi sUiT aVanT de cOmmencer
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (H) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente
peu concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
direcTiVes d'applicaTiOn des aUTOcOllanTs
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son support
en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
remarQUe: les autocollants sont compatibles avec les
solutions de fixage ou les solvants.
or, please write to:
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
* ASSEMBLY CAUTION
* CEMENT TOGETHER
`
`
* A COLLER
*ATTENTION D ASSEMBLEE
(800) 833-3570
85289610200
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Aluminum
Aluminium
Flat Grey
Gris mat
Satin Dark Grey
Gris foncé satiné
Satin Grey
Gris satiné
Satin Black
Noir satiné
Acier
Steel
Satin Red
Rouge satiné
Silver
Argent
Flat Brown
Brun mat
Satin Brown
Brun satiné
Gloss Red
Rouge brillant
Gloss Blue
Bleu brillant
Transparent Red
Rouge transparent
Turn Signal Amber
Feu clignotant de
direction ambre
* DO NOT CEMENT
* NE PAS COLLER
Need help?
Do you have a question about the KIT 2896 and is the answer not in the manual?
Questions and answers