Specifications; Special Functions - Sanyo CE28WN5-B Instruction Manual

TV Specifications
Common specification
Power source
Television system
Colour system
Channel coverage
Aerial input impedance
AV terminal
21-pin terminals AV1: CENELEC Standard with RGB
AV2: CENELEC Standard with S-inputs
Front AV terminals AV3: RCA Terminal, Video and
Audio(L/R) Input
Sound output Main L/R 10 x 2 (28" and 32" models)
(Continuous) (watts)
CE28WN5-B
Picture tubes 28
(inches)
Dimensions 779 x 524 x 511.5
(W x H x D mm)
Weight (kg) 32.5
Specifications subject to change without notice.
Pin Signal function
Pin 1 Audio output (right channel)
Pin 2 Audio Input (right channel)
Pin 3 Audio output (left channel)
Pin 4 Audio earth
Pin 5 Earth (blue)
Pin 6 Audio Input (left channel)
Pin 7 Blue (B) input
Pin 8 Remote switch input
Pin 9 Earth (green)
Pin 10
Pin 11 Green (G) input
Pin 12
Pin 13 Earth (red)
Pin 14 Earth
Pin 15 Red (R) or C(chrominance) input
Pin 16 Fast blanking
Pin 17 Earth(video)
Pin 18 Earth
Pin 19 Video output
Pin 20 Video/sync *1 or Y (luminance) input
Pin 21 Connector shield
20
SPECIFICA TIONS / SPECIAL FUNCTIONS
SPECIFICA TIONS / SPECIAL FUNCTIONS
AC 220~240V 50Hz
System I
PAL/NTSC4.43
(PAL/NTSC4.43/NTSC3.58 in
AV mode)
UHF: 21-69
75 ohm
CE32WN5-B
32
880 x 577.5 x 567
46.3
Scart Specifications
Level
0.5V/ 1 K ohm
0.5V/10 K ohm
0.5V/ 1 K ohm
0.5V/10 K ohm
0.7Vpp/75 ohm
L:0-2V H:10-12V
M: 4.5-9.5V -> 16:9 mode
0.7Vpp/75 ohm
0.7Vpp/75 ohm
L:0-0.4V H:1-3V
1 Vpp/75 ohm
1 Vpp/75 ohm

Special Functions

This TV set allows you to set up the following special functions.
Prohibition of presetting, CS key entry
ITEM-1 SET 0 NO
SET 1 YES
Start up programme position
ITEM-2
Presets the programme position when the set is switched on.
SET -> 0 Last programme position start
SET -> 1 Programme position "1" start
SET -> 2 Programme position "2" start
SET -> 3 Programme position "3" start
SET -> 4 Programme position "4" start
SET -> 5 Programme position "5" start
SET -> 6 Programme position "6" start
SET -> 7 Programme position "7" start
SET -> 8 Programme position "8" start
SET -> 9 "AV1" start
SETTING PROCEDURE
1 . To enter the special function mode,
press and hold the
the Remote control handset and then
press the P button on the TV set.
2 . To select the "Item" number, press the
F/OK button on the remote control handset.
3 . To select the "Set" number, press the
4 . To return to the normal TV mode, press the
The setting conditions of all items can be confirmed.
Special functions are not cancelled if the TV set is switched off
or the mains disconnected.
AV1
*
Red input
*TV output
*
Video/sync-input
Sets prohibition of presetting and
CS key entry.
?
button on
ITEM-1 SET -> 0
or button repeatedly.
?
button.
AV2
*
monitor out
*
monitor out
*
C-input
*
monitor output
*
Video/Y-input